XPiQ inc PUP130-12, PUP130-13, PUP130-13-1, PUP130-14, PUP130-16 Datasheet

DESCRIPTION

The PUP80/130 Series of AC-DC switching power supplies
provide 60-130 watts of continous output power. They
are enclosed in a 94V-1 rated polyphenylene-oxide case
with an IEC320 inlet connector to mate with an
interchangable cord for worldwide use. All
models meet CISPR 22 and FCC Class B
emission limits and comply with UL,
CSA, IEC and CE requirements.

FEATURES

• Built-in EMI filter

• Overvoltage protection

• Overcurrent protection

• Auto-ranging input

• Input surge current protection

• 100% burn-in at full load

• Optional on/off switch

Output Maximum

Output

Model Vnom Imin Imax Tol. Power

PUP80-10 5V 0A 12A 2% 60W
PUP80-10-1 7V 0A 8.6A 2% 60W
PUP80-11 10V 0A 6.0A 2% 60W
PUP80-12 12V 0A 6.7A 4% 80W
PUP80-13 15V 0A 5.3A 3% 80W
PUP80-13-1 18V 0A 4.5A 3% 80W
PUP80-14 24V 0A 3.4A 3% 80W
PUP80-16 30V 0A 2.7A 2% 80W
PUP80-17 36V 0A 2.3A 2% 80W
PUP80-18 48V 0A 1.7A 2% 80W
PUP130-12 12V 0A 10.8A 5% 130W
PUP130-13 15V 0A 8.6A 4% 130W
PUP130-13-1 18V 0A 7.2A 4% 130W
PUP130-14 24V 0A 5.4A 3% 130W
PUP130-16 30V 0A 4.3A 3% 130W
PUP130-17 36V 0A 3.6A 2% 130W
PUP130-18 48V 0A 2.7A 2% 130W

OUTPUT VOLTAGE/CURRENT RATINGS CHART

NEW • UNIVERSAL INPUT

• DESKTOP POWER SUPPLIES

U

L

®

®

International Power Sources, Inc.

60-130 WATT

SWITCHING

POWER SUPPLY

98

GENERAL SPECIFICATIONS

All specifications are typical at nominal line, full load, and 25°C.

Efficiency: 70% minimum Vo > 12V

65% minimum on other models

Hold-up time:

PUP80 Series: 15msec minimum at 110 VAC

PUP130 Series: 10msec minimum at 110 VAC
Line regulation: ±0.5% maximum at full load
Inrush current: 15A@115 VAC, or 30A@

230 VAC at 25°C cold start

Withstand voltage: 3000 VAC from input to output

1500 VAC from input to ground
500 VAC from output to ground

Insulation resistance: 10 Mohm minimum from output

to ground

Operating temperature: 0°C to +60°C (PUP80 series)*

0°C to +70°C (PUP130 series)*
Storage temperature: –40°C to +85°C
Relative humidity: 5% to 95% non-condensing
MTBF: 100,000 hours minimum at

full load at 25°C ambient
EMI requirements: In compliance with radiated and

conducted limits of CISPR 22

(EN 55022) Class B and FCC Class B
Safety requirements: Approved to:

a) UL 1950

b) CSA C22.2 No. 234

c) IEC 950 (EN60950)
Switchng frequency 60KHz to 75KHz

INPUT SPECIFICATIONS

Input voltage: 85 to 132 VAC or 170 to 264 VAC

(auto-ranging)
Input frequency: 47 to 63 Hz
Input current:

PUP80 Series: 1.8A (rms) for 115 VAC

1.0A (rms) for 230 VAC

PUP130 Series: 3.0A (rms) for 115 VAC

1.7A (rms) for 230 VAC

Safety ground: 0.40mA max. @ 110VAC 60 Hz

leakage current: 0.80mA max. @ 240VAC 50 Hz

OUTPUT SPECIFICATIONS

Total output power: See rating charts
Ripple and noise: 1% peak to peak maximum
Overvoltage protection: Set at 112-132% of its

nominal output voltage

Overcurrent protection:

Protected under short circuit conditions
Temperature coefficient: ±0.04%/°C maximum
Transient response: Maximum excursion of 4% or better

on all models, recovering to 1% of

final value 500us after a 25% step

load change
Remote sense: Optional, please consult factory

*

PUP80: Derate linearly from 100% load at 40°C to 50% load at 60°C

*

PUP130: Derate linearly from 100% load at 50°C to 50% load at 70°C

MECHANICAL SPECIFICATIONS

PIN CHART

Model PIN 1 2 3 4 5 6 7 8

All Models RETURN RETURN OUTPUT RETURN OUTPUT RETURN OUTPUT OUTPUT

+V +V +V +V

NOTES:

1. Dimensions shown in inches (mm)

2. Tolerance 0.02 (0.5) Maximum

3. Optional output connectors available

4. Optional ON/OFF switch available

5. DC fan on PUP130 models only

2.50 (63.5)

AC INPUT IEC 320 INLET

99

Your Source of Power ...

260 Hopping Brook Road, Holliston, MA 01746

TEL: [phone] FAX: [phone]

http://www.intlpower.com

International

Power Sources, Inc.