XPiQ inc PM110-10-1A, PM110-10A, PM110-12A, PM110-13A, PM110-14A Datasheet

110 Watts

PM110 Series

4000 VAC Isolation

•

100% Burn-in

•

Low Safety Leakage Current

•

Wide Input Voltage 85 to 264 VAC

•

Meets EMI Requirements of

Medical Equipment

•

Both Line and Neutral Fused for

European Requirements

•

•

•

Specification

All specifications typical at nominal line, full load and 25°C

PH: 508 429.9883

FAX: [phone]

Email: [e-mail]

Holliston, MA 01746 USA

www.XP-iQ.com

Intelligent Design Quality Product

XPiQ inc.

Medical Switching Power Supply

Input

Input Voltage • 85 to 264 VAC
Input Frequency • 47 to 440 Hz

Input Current • 3.20A (rms) for 115 VAC

1.8A (rms) for 230 VAC
Safety Ground • 50µA max. at 110 VAC 60 Hz
Leakage Current • 100µA max. at 240 VAC 50 Hz

Output

Total output power: • 0 to 110 watts
Ripple and noise: • 1% peak to peak maximum
Overvoltage • Provided on output #1 only;

Protection: set at 112-132% of its nominal

output voltage

Overcurrent • All outputs protected to short
Protection: circuit conditions

Temperature • All outputs ±0.04%/°C
Coefficient: maximum

Transient Response: • Maximum excursion of 4% or

better on all models, recovering
to 1% of final value 500us after
a 25% step load change

Line Regulation • ±0.5% max. at full load

General

Efficiency • 65% minimum at 110 watt output
Hold-up time • 12 msec minimum at nominal input
Inrush Current • 15 amps at 115 VAC or 30 amps at

230 VAC at 25°C cold start

Withstand Voltage • 4000 VAC from input to output

1500 VAC from input to ground
500 VAC from output to ground

Insulation Resistance • 10 Mohm minimum from

output to ground

Environmental

Operating • 0°C to +70°C*
Temperature

Storage • -40°C to +85°C
Temperature

Relative Humidity • 5% to 95% non-condensing
MTBF • 100,000 hours minimum at full load

at 25°C ambient

EMI Requirement • Meets the conducted limits of

EN 55011 (CISPR11) Level B

Safety Requirements • Approved to: (Not for patient contact)

a) UL2601
b) CSA C22.2 No.601.1-M90 per CUL
c) IEC 601-1/EN60601-1 (per TUV)

* Derate linearly from 100% load at 50°C to 50% load at 70°C

Output #1 Output #2 Output #3 Output #4 Maximum

Output

Model Vnom Imin Imax Tol. Vnom Imin Imax Ipeak1Tol. Vnom Imin Imax Tol. Vnom Imin Imax Tol. Power

2

PM110-10-1A 3.3V 0.0A 22.0A 3% 110W
PM110-10A 5.0V 0.0A 22.0A 3% 110W
PM110-12A 12.0V 0.0A 9.0A 2% 110W
PM110-13A 15.0V 0.0A 7.5A 2% 110W
PM110-14A 24.0V 0.0A 4.5A 2% 110W
PM110-16A 30.0V 0.0A 3.6A 3% 110W
PM110-23A +5.0V 0.0A 10.0A 3% +12V 0A 5A 9.0A 3% 110W
PM110-31A +5.0V 0.0A 10.0A 3% +12V 0A 5A 9.0A 3% -12V 0A 1A 4% 110W
PM110-32A +5.0V 0.0A 10.0A 3% +15V 0A 4A 9.0A 3% -15V 0A 1A 4% 110W
PM110-40A +5.0V 0.0A 10.0A 3% +12V 0A 5A 9.0A 3% -12V 0A 1A 4% -5V 0.0A 1A 4% 110W
PM110-41A +5.0V 0.0A 10.0A 3% +15V 0A 4A 7.5A 3% -15V 0A 1A 4% +24V 0.0A 1A 4% 110W
PM110-42A +5.0V 0.0A 10.0A 3% +12V 0A 5A 9.0A 3% -12V 0A 1A 4% +12V 0.0A 1A 4% 110W
PM110-45A +5.0V 0.0A 10.0A 3% +12V 0A 5A 9.0A 3% -12V 0A 1A 4% +24V 0.0A 1A 4% 110W
PM110-45-1A +5.0V 2.0A 10.0A 3% +12V 0A 5A 9.0A 3% -12V 0A 1A 4% +24V 1.5A 3A 10% 110W
PM110-45-2A +5.0V 0.0A 10.0A 3% +24V 0A 3A 5.0A 3% -12V 0A 1A 4% +12V 0.0A 1A 4% 110W
PM110-46A +5.0V 0.0A 10.0A 3% +15V 0A 4A 7.5A 3% -15V 0A 1A 4% -5V 0.0A 1A 4% 110W

Model PIN 1, 2, 3 4, 5 6, 7 8, 9 10 11 12 13
PM110-10-1A PM110-10A OUTPUT RETURN RETURN OUTPUT P.F.D N.C. KEY N.C.
PM110-12A PM110-13A #1 #1
PM110-14A PM110-16A
PM110-23A OUTPUT COMMON COMMON OUTPUT P.F.D. OUTPUT KEY N.C.

#1 RETURN RETURN #2 #2

PM110-31A PM110-32A OUTPUT COMMON COMMON OUTPUT P.F.D. OUTPUT KEY N.C.

#1 RETURN RETURN #2 #3
PM110-40A PM110-41A OUTPUT COMMON COMMON OUTPUT P.F.D. OUTPUT KEY OUTPUT
PM110-42A PM110-45A #1 RETURN RETURN #2 #3 #4
PM110-45-1A PM110-45 -2A
PM110-46A

PH: 508 429.9883

FAX: [phone]

Email: [e-mail]

Holliston, MA 01746 USA

www.XP-iQ.com

OUTPUT VOLTAGE & CURRENT RATINGS PM 110

Notes

•

Mechanical Details

Pin Chart

Note:

1. Dimensions shown in inches (mm)

2. Tolerance 0.02 (0.5) maximum

3. Input connector mates with Molex housing 09-50-3051 and
Molex 2878 series crimp terminal

4. Output connector mates with Molex housing 09-50-3131
and Molex 2878 series crimp terminal

5. Weight: 600 grams approx.

1. Peak output current with 10% maximum duty cycle for less than 60 seconds.
Total peak power must not exceed 110 watts.

2. 110 watts maximum at 25 CFM forced air cooling or 80 watts maximum at convection cooling.

Mounting Holes
Threaded insert
for M3 screws
(4 places)