Xomax 2DTSBN6000 Instruction Manual

Download

Page 1

Please read all instructions carefully before using

2DTSBN6000

Page 2

INSTRUCTIONSINSTRUCTIONS

Trouble shooting

PROBLEM CAUSE

CORRECT ACTION

Poor performance of radio station

Connot load disk

There is a disk inside

Eject disk,then,slot in new disc.

After ignition switch off ,setting information all lose

Reset information and save

Change battery or fuse

Cannot power on

Check whether power fuse melt or not

Change fuse same as the old one

Some factors cause MPU wrong operation

Press RES button on the panel by pen point, then, power on

Weak signal

Move the car to another place, then research

Cannot play disc

Disc is scratched

Change new disc

Put wrong side of disc into the unit

Slot in the disk with sign side up

Clean lens by lens clean discLens has dirty

Cannot switch language/subtitle

There is only one language/ subtitle in disc

If disc is not with multi-language/ subtitle, it cannot switch language/ subtitle

No image

Other factors cause MPU wrong operation

Press [RES] button on the panel by penpoint, then, power on

Cannot watch image during driving

It’s not allowed to watch image during driving

Park the car in a safe place, put the car stall in “ P ”postion, pull up the hand brake

CONTENTS

NOTE

instructions will not enjoy the warranty.

2. To drive safely and avoid break the traffic rules, do not watch program and operate the unit while driving.

3. To avoid short circuit, please do not exposure the device to rain.

4. To avoid short circuit, please do not put in the device or any metal objects left behind.

5. Not open the machine for maintenance by yourself, please go to the professional repair service station for repairing.

6. When the engine is turned off, please do not use the car audio a long time, otherwise the battery may run out.

7. Do not insert anything to the device’s vent and other openings.

8. Damage to the screen carefully! Do not use sharp objects push, rub, Stroke the screen.

1. Please read the instructions before using the unit, the damage caused by not following the

Panel Introduction

Remote controller operation

Turn on/off Host

Access main interface

U Disc/SD Card function operation

Radio Function Operation

Disc Function Operation

Bluetooth Function Operation

External input operation (Optional)

GPS Navigation Function Operation

Other functions

Foreground/background Setup

Sound Setup

Navigation Path Setup

Language Setup

Radio Area Setup

Backlight

Touch Screen Calibration

Steering Wheel Setup

Time setup

Trouble shooting

Page 3

INSTRUCTIONSINSTRUCTIONS

0314

Backlight

Via backlight setup interface, you can manually adjust the display screen brightness according to the intensity of light of the environment to achieve satisfactory effect.

Touch Screen Calibration

If errors occur in touch position, you can calibrate touch coordinates. Enter touch calibration interface, Use a touch pen to click the central area of symbol “+”, calibrate the screen in the moving sequence of the central area of “+”. After calibration is completed, system will automatically save data and exit the screen.

Steering Wheel Setup

You can also perform control to the unit by the steering wheel of the car. Connect the positive and negative terminal of the car SWC cable with the positive and negative terminal of the SWC cable of the unit respectively. Click buttons on the steering wheel one by one and keep a record of relevant sequences. Click appropriate function setup to save the settings.

Time setup

Touch [Time] icon in the main interface to enter into the calendar setup interface. Click the display position of year/ month/day/hour/minute to reset the current parameters. Set in the time interface touch 12HR/24HR icon to switch between clock modes.

Panel Function

1. SRC button

When the power on, press this button to turn on/off host; in any application procedure, press this button can switch to the main interface.

2.MODE button

When the unit is power on, Repeat press this button can switch to different function mode as following picture. Note: When the device without connecting to USB, SD, CDC or DVD no disc inside, the system will automatically skip these related working mode.

3.FM/AM button

In any mode, press the button to radio mode. In radio mode, press the button to switch band.

4. AUX IN

To input external audio.

5.RESET

Press this button can back to default mode.

Press this button can eject the disc.

7.EQ button

In a source mode, press the button to enter equalizer setup.

8.DVD button

In any mode, press this button to read the disc.

9.NAVI button

Press the button to enter into/exit navigation interface.

CDC

AUX

USB

DVD

RADIO

GPS

(Optio nal)

Page 4

INSTRUCTIONSINSTRUCTIONS

1304

Access setup interface

Click [Setup] icon on main interface to access setup interface. Touch each function icon to enter into the corresponding function operation.

Foreground/background Setup

You can enable background mode by foreground/background setup. When the unit is connected with background device, you can enable background mode of the unit to play audio and video files. At the Set interface Touch [Foreground/background] icon, Enter into foreground/background setup interface. Only in radio/bluetooth/navigation mode can background mode be enabled.

Sound Setup

Touch [Sound Setup] icon to enter sound setup interface. Sound effect setup: select general, pop, classic or rock, you can adjust to the best audio effect according to your preferences.

System volume: adjust volume level of the whole unit. Bluetooth volume: adjust volume level of bluetooth mode. Navigation volume: adjust volume level of navigation mode. Reverse volume: adjust volume level of reverse mode. Screen click sound: select to turn screen click sound on/off. After click sound is turned off,

there is no beep sound when you touch the screen.

Loudness: Select the turn on/off loudness function. Tweeter/woofer/subwoofer: adjust volume level of tweeter/woofer/subwoofer. Left front speaker attenuate: adjust volume level of left front speaker. Right front speaker attenuate: adjust volume level of right front speaker. Left rear speaker attenuate: adjust volume level of left rear speaker. Right rear speaker attenuate: adjust volume level of right rear speaker.

Navigation Path Setup

Navigation path is already set when you buy the product. Do not enter into the navigation setup interface to change path arbitrarily. Otherwise you may cause navigation program abnormal.

Language Setup

During use, you can select your familiar language to display menu by language setup. At the language set interface click appropriate language icon, the selected language will be displayed as the menu language.

Radio Area Setup

You need to select your radio area before you use radio function.

10.SD slot

Connect the SD memory card to this socket, and the unit can play MP3 music.

11.USB slot

Connect the USB memory to this socket, and the unit can play music format files supported by this unit in the USB memory.

12.Disk load slot

Opening for disks to enter or retreat.

13.MUTE button

Press this button to shut off the sound output, re-press this button can resume the sound output, long press this button can turn off the TFT LCD display.

14.IR

To receive infrared signals from the remote control matched with the unit.

15. MIC

Input socket for microphone.

16.MAP slot

Insert map card to read navigation map data.

Page 5

INSTRUCTIONSINSTRUCTIONS

0512

GPS Navigation Function Operation

In tune

Among tall buildings

At the boulevard

The antenna is sheltered

Underground parking

Overpass or viaduct

Navigation Function Operation

For detailed operation of navigation function, see “Navigation Operation Manual”.

Receiving signal error

When the satellite signals can be normally received, the error of standard GPS shall be about 7 meters. Driving on parallel sections, there shall be error even the product has auto-correct function. The normal receiving of satellite signals shall be affected and cause error in following environment:

Other functions

Rearview function

In any running state, the video signal can switch to reverse video state when reversing the car, and the system shall return to its initial running state after reversing the car.

Do not rely on CCD system completely, please make sure your car is safe by your eyes during driving. Back rearview system only assists in driving. As the distance range of rearview system is limited, completely relying on the rearview system during driving may cause accidents.

Reverse field simulation

Rearview backup image

Warning

Page 6

INSTRUCTIONSINSTRUCTIONS

1106

Bluetooth music playback

Bluetooth player can play music files in cellphone via wireless audio device on condition that the cellphone supports relevant bluetooth protocol. After bluetooth device gets connected to the unit, audio system will automatically link with the paired cellphone. In some cases, you need to enable the playback of audio files by phone keypad due to different phone models.

Play/pass

the previous/next song

Stop

External input operation (Optional)

Connect the video input plug with external video input jack, and connect the audio input plug with external audio input jack. Touch [Input] icon on main interface to access external input interface.

Page 7

INSTRUCTIONSINSTRUCTIONS

0710

Bluetooth Function Operation

The system provides bluetooth handsfree communication function, if your cellphone supports bluetooth function, you can establish a point-to-point connection between your cellphone and the system. The system can also achieve the dialing, answering function, A2DP, the function of phonebook on the screen.

Pair/link

The first time you pair your cellphone with the unit, the procedures below should be followed:

① Turn the bluetooth function of your cellphone on. ②The cell phone searches for bluetooth device and connect.

③A prompt is displayed on the screen of the phone, to accept pair, enter the same numeric code on the phone (0000) and press [OK] button.

④ After the pair is completed, the name of the connected cellphone is displayed on the screen. ⑤ After recharged, the bluetooth system will automatically get connect to the lastly

disconnected cellphone.

Turn on/off Host

When the ignition switch is put in ACC or ON position, Press[ ] button on the front panel to turn on the unit. After the host starts, hold [ ]button for 3 seconds , the host will turn off.

Access main interface

In boot-up state, press /SRC/MENU button on the panel to switch to main interface.

Touch page. Touch the icon does not go into a long free mobile icon location. Touch the icons to enter the corresponding functions. Touch in two different interface style to switch between.

icon or at the touch pen / finger gently sliding the screen to switch the main menu

Rear view function menu (optional)

When the machine has a menu function, rear view, in the main screen, click icon to enter the menu after reversing interface.

U Disc/SD Card function operation

When there is a USB device/SD card connected, the unit can conduct the playback of audio/ video/image files in the USB device/SD card.

Insert/eject SD card

1. Insert a SD card recorded with media information into the SD card slot in the unit correctly

until it is locked.

2. When pulling out the SD card, exit SD card playing state first, then press the SD card and it shall pop up after unlocking.

Insert/Eject USB storage device

1. Connect a U disc recorded with media information to the unit by a USB connecting cable.

2. When there is a need to eject the USB device, exit the USB device playback screen first, and then take out the device.

Note: When the unit has front USB, only one of them.

Radio Function Operation

Touch [ RADIO ] icon in the main interface to enter into the radio interface. Search/store station

1. Auto search and store station

(1) Touch [ ] icon in the radio interface on the panel to search for station automatically. During search, the searched stations will be stored automatically. (2) During search, retouch [ ] icon to stop auto searching.

Phonebook

After the cellphone gets connected to the unit, you can read records in the phonebook of your cellphone and store information in the phonebook of the unit. phones may not support the phone book.)

( Note: Some

Call records

Recent dialed calls, received calls and missed calls can be saved in call records.

Select missed/dialed/ received calls

Clear all

After the successful pair, the bluetooth that indicates connecting status will be lighted, otherwise, it will appear dimmed. Touch [Disconnect] to disconnect the current connection; after disconnected。 Touch [Connect] to connect the disconnected bluetooth device. Touch [Reset] icon to clear all pair records.

Bluetooth Interface Function Introduction

Dial

Call records

Phonebook

Music playback

Switch

Page 8

INSTRUCTIONSINSTRUCTIONS

0908

Disc Function Operation

Play/eject disc

Insert the disc into the disc slot with the printing surface up, system will detect the disc and automatically take it in to read and play. Click button on the panel to eject the disc. If a disc has not been took away 15 seconds after it is ejected, system will automatically take in the disc but not play.

Note: Do not insert two discs or more.

Playback Menu

During playback of disc, touch the middle lower area of the screen to pop up the touch menu, operate the touch menu to perform various playback controls.

Note: Touch the top left corner of the screen to return to the main interface.

DVD/VCD disc playback

When there is a disc in the unit, touch icon in the main interface, system enters into disc reading status. When the disc does not have play menu, system will automatically read the disc and directly play; when the disc has play menu, system displays DVD menu, you can touch appropriate options on the screen to access the corresponding items.

CD Disc Playback

When there is a disc in the unit, touch icon in the main interface, system enters into disc reading status. After disc format is read, the screen will display the CD playback interface, system will automatically read the disc contents and display on the screen, You can directly click song name to select and play, you can also click the numeric keypad button and enter song number to selected your favorite song to play.

MP3/WMA format disc playback

Put the MP3/WMA disc in DVD player, after the disc is read, system enters into the interface as is shown below: Touch the file name icon and the song to read and play. Touch to select the previous/next file. Playback control function keys and DVD Play control keys are functioning.

Play/pause

Stop

The songprevious/next

Fast /backward forward

Repeat/Repeat all discs

settings

002 Big big world

001 \

003 My Heart

001 My Heart 1.MP3 002 My Heart 1.MP3

003 My Heart 1.MP3

004 My Heart 1.MP3 005 My Heart 1.MP3

1 2

2. Manual search and store station

(1) Finger / touch pen drag of high radio frequency scale can be achieved manually search for radio stations. During search, after a station is searched, the unit will stop searching automatically and play the searched station radio. (2) Directly touch[ / ] icon in the radio interface to fine-tune station frequency. (3) After a station is searched, (such as: 88.15MHZ), long press any position in the pre-stored station list in the radio main interface, the searched station will be stored in the selected position. (4) FM band can save 18 stations (Fm1/FM2/FM3 can each save 6), AM band can save 12 stations (AM1/AM2 can each save 6). (5) During search, the unit will automatically stop searching after it has searched for all stations through once.

3. Select station/band switch/switch between LOC/DX

(1) Directly touch any station in the pre-stored station list in radio interface to play the selected station. (2) Touch button in radio interface to switch band among Fm1,FM2, FM3, AM1 and AM2. (3) Touch icon to switch search mode between LOC and DX. When LOC function is turned on, only those radio stations with strong signals and good reception can be received; When DX function is turned on, distant weak radio signals can be received.

4. RDS function

RDS provides a series of information (such as traffic information and station name), and can automatically switch to a station with strong signals and carries the same program. RDS data contains the following contents: P1---program identification TA---traffic announcement PS---program service name PTY---program type name AF---alternative frequencies EON---enhanced other network TP---traffic program Touch the upper right corner [RDS] radio interface icon, enter the RDS interface: Function Operation ① TA ( Receive traffic information ) ON: When the traffic station is turned on, the radio will automatically search for traffic stations. After a station is searched, screen displays “TP”. Only when traffic information is broadcasted can it be received, after traffic information is completed, the radio will automatically switch to the previous mode. OFF: Repress [TA] button to close TA function. In other modes, traffic announcement will automatically switch to radio mode, after the traffic announcement is completed, it will automatically switch to the previous mode. ② AF Touch the button to turn the AF function on/off. AF function is turned on, When the received station signals become weak, the radio will automatically fine-tune to other frequencies. When receiving an emergency announcing, the screen will display warning message “ALARM“. ③ EON ON: Open EON function, another AF list is received. OFF: Close EON function. ④ REG ON: Open REG function, only local RDS stations can be received. OFF: Close REG function.