XLT XD-9004A User Manual
XD-9004A
GA-SWC-HB
04/09/2012
XLT Gas Oven & AVI Hood
Installation & Operation Manual
This appliance is for professional use by qualified personnel. This appliance must be installed
by qualified persons in accordance with the regulations in force. This appliance must be installed with
sufficient ventilation to prevent the occurrence of unacceptable concentrations of substances harmful
to health in the room in which it is installed. This appliance needs an unobstructed flow of fresh air for
CAUTION
Current versions of this manual, Rough-In Specifications, Parts & Service Manual, Architectural Drawings,
For use with the following XLT GAS Oven Versions:
Standard (S) C
World (W) C
satisfactory operation & must be installed in a suitably ventilated room in accordance with current
regulations. This appliance should be serviced by qualified personnel at least every 12 months or
sooner if heavy use is expected.
& a list of International Authorized Distributors are available at: www.xltovens.com
For use with the following AVI Gas Hood Versions:
Standard (S) B
World (W) B
2000887
XLT Ovens
PO Box 9090
Wichita, Kansas 67277
US: 888-443-2751 FAX: 316-943-2769 INTL: 316-943-2751 WEB: www.xltovens.com
2
WARNING & SAFETY INFORMATION
SAFETY DEPENDS ON YOU
Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury, or death. Read the installation, operating and maintenance in-
WARNING
Post in a prominent location instructions to be followed in the event you smell gas. This infor-
mation can be obtained by consulting your local gas supplier.
WARNING
In the event a gas odor is detected, shut off the gas at the main shutoff valve immediately.
Contact your local Gas Company or supplier.
Do not restrict the flow of combustion and/or ventilation air to the unit. Provide adequate
clearance for operating, cleaning, & maintaining the unit & adequate clearance for operating
the gas shutoff valve when the unit is in the installed position.
Keep the area free & clear of combustible material. DO NOT SPRAY AEROSOLS IN THE
VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION.
Ovens are certified for installation on combustible floors.
Electrical schematics are located inside the control box of the oven & and in this manual. Dis-
connect input power to the unit before performing any maintenance.
This unit requires a ventilation hood. The installation must conform to local codes.
This unit may be operated with either natural gas or LP fuel as designated on the nameplate
label located on the side of the unit.
This unit must be operated by the same voltage, phase, & frequency of electrical power as des-
ignated on the nameplate label located on the side of the unit.
Minimum clearances must be maintained from combustible & non-combustible construction
materials.
Follow all local codes when installing this unit.
Follow all local codes to electrically ground the unit.
Appliance is not to be cleaned with high pressure water.
XLT ovens are certified for use in stacks of up to three (3) units of XLT products. Integration
of other manufacturer’s products into an oven stack is not recommended, & will void any war-
ranties. XLT Ovens assumes no liability for mixed product applications.
Failure to call XLT Customer Service at 1-888-443-2751 prior to contacting a repair company
voids any & all warranties.
PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE.
structions thoroughly before installing, using, or servicing this equipment.
FOR YOUR SAFETY
Do not store or use gasoline or other flammable liquids or vapors in
the vicinity of this or any other appliance.
XLT Ovens has spent millions of dollars designing and testing our products as well as de-
veloping Installation & Operation Manuals. These manuals are the most complete and easiest to
understand in the industry. However, they are worthless if they are not followed.
We have witnessed store operators and building owners lose many thousands of dollars in
lost revenue due to incorrect installations. We highly recommend you follow all instructions given
in this manual as well as follow best practices in plumbing, electrical, and HVAC building codes.
Technical Support US: 888-443-2751 Technical Support INTL: 316-943-2751
WARNING & SAFETY INFORMATION
Definitions & Symbols
A safety instruction (message) includes a “Safety Alert Symbol” & a signal word or phrase
such as WARNING or CAUTION. Each signal word has the following meaning:
This symbol indicates high voltage. It calls your attention to items or operations
that could be dangerous to you & other persons operating this equipment. Read the
HIGH
VOLTAGE
WARNING
CAUTION
message & follow the instructions carefully.
Indicates a potentially hazardous situation that, if not avoided, can result in serious
injury or death.
Indicates a potentially hazardous situation, that if not avoided, can result in minor to
moderate injury or serious damage to the product. The situation described in the
CAUTION may, if not avoided, lead to serious results. Important safety measures are
described in CAUTION (as well as WARNING), so be sure to observe them.
3
NOTE
TIP
Notes indicates an area or subject of special merit, emphasizing either the product’s
capability or common errors in operation or maintenance.
Tips give a special instruction that can save time or provide other benefits while installing
or using the product. The tip calls attention to an idea that may not be obvious to first-time
users of the product.
Technical Support US: 888-443-2751 Technical Support INTL: 316-943-2751
4
WARRANTY - US & Canada
XLT warrants gas ovens manufactured after April 1, 2009 utilizing quietFIRE™ burners
and all electric ovens manufactured after April 1, 2011 to be free from any defect in material and
workmanship under normal use for five (5) years from the date of original purchase by the end
user, and further warrants main fan blades, conveyor shafts, and conveyor bearings for ten (10)
years. XLT further warrants all ovens to be free from rust for ten (10) years from the date the
equipment is originally purchased. XLT warrants AVI hoods to be free from any defect in material and workmanship under normal use for two (2) years from the date of original purchase by the
end user. In the event of a part failure, XLT will furnish a replacement part and pay for all labor
associated with the replacement of the part if, upon inspection, XLT determines that the part is defective. This warranty is extended to the original end user purchaser and is not transferable without prior written consent of XLT. Damages are limited to the original purchase price.
DUTIES OF THE OWNER:
The owner must inspect the equipment and crates at time of receipt. Damage during shipment
is to be immediately reported to the carrier and also to XLT.
The equipment must be installed and operated in accordance with the written instructions fur-
nished with the unit.
This warranty shall not excuse the owner from properly maintaining the equipment in accor-
dance with the written instructions furnished with the unit.
A copy of the “Initial Start-Up Checklist” must be filled out and returned to XLT Ovens and
the Authorized Distributor when the unit is initially installed, and/or when the unit is removed
and installed in another location.
The gas, electric, and HVAC utilities must be connected to the oven and installed by locally
licensed contractors.
Failure to contact XLT Ovens prior to contacting a repair company for warranty work voids
any and all warranties.
WHAT IS NOT COVERED:
The following items are not covered by this warranty:
Freight damage
Any part that becomes defective because of utility services (power surges, high or low volt-
ages, high or low gas pressure or volume, contaminated fuel, or improper utility connections)
Conveyor belts
Filters
Exhaust Fans
Light Bulbs
Normal maintenance or adjustments
This warranty shall not apply if the equipment or any part is damaged as a result of accident,
casualty, alteration, misuse, abuse, improper cleaning, improper installation, improper operation, natural disasters, or man-made disasters.
CLAIMS HANDLED AS FOLLOWS:
Should any such defect be discovered, XLT must be notified. Upon notification, XLT will arrange
for necessary repairs to be made by an authorized service agent. Denial of services upon the arrival of an authorized service agent will release XLT of any and all warranty obligations.
Technical Support US: 888-443-2751 Technical Support INTL: 316-943-2751
LIMITED WARRANTY - INTERNATIONAL
5
XLT warrants gas ovens manufactured after January 1, 2011 utilizing quietFIRE™ burners
and all electric ovens manufactured after April 1, 2011 to be free from any defect in material and
workmanship under normal use for two (2) years from the date of original purchase by the end
user. XLT warrants AVI hoods to be free from any defect in material and workmanship under normal use for one (1) year from the date of original purchase by the end user. In the event of a part
failure, XLT will furnish a replacement part to the Authorized Dealer if, upon inspection, XLT determines that the part is defective. The Authorized Dealer will pay for all labor associated with the
replacement of the part. This warranty is extended to the original end user purchaser and is not
transferable without prior written consent of XLT. Damages are limited to the original purchase
price.
DUTIES OF THE OWNER:
The owner must inspect the equipment and crates at time of receipt. Damage during shipment
is to be immediately reported to the carrier and also to XLT.
The equipment must be installed and operated in accordance with the written instructions fur-
nished with the unit.
This warranty shall not excuse the owner from properly maintaining the equipment in accor-
dance with the written instructions furnished with the unit.
A copy of the “Initial Start-Up Checklist” must be filled out and returned to XLT Ovens and
the Authorized Dealer when the unit is initially installed, and/or when the unit is removed and
installed in another location.
The gas, electric, and HVAC utilities must be connected to the oven and installed by locally
licensed contractors.
Failure to contact the Authorized Dealer prior to contacting a repair company for warranty
work voids any and all warranties.
WHAT IS NOT COVERED:
The following items are not covered by this warranty:
Freight damage
Any part that becomes defective because of utility services (power surges, high or low volt-
ages, high or low gas pressure or volume, contaminated fuel, or improper utility connections)
Conveyor belts
Filters
Exhaust Fans
Light Bulbs
Normal maintenance or adjustments
This warranty shall not apply if the equipment or any part is damaged as a result of accident,
casualty, alteration, misuse, abuse, improper cleaning, improper installation, improper operation, natural disasters, or man-made disasters.
CLAIMS HANDLED AS FOLLOWS:
Should any such defect be discovered, the Authorized Dealer must be notified. Upon notification,
the Authorized Dealer will arrange for necessary repairs to be made by an authorized service
agent. The Authorized Dealer will notify XLT Ovens of all discovered defects.
Technical Support US: 888-443-2751 Technical Support INTL: 316-943-2751
6
RECEIVING & INSPECTION
NOTIFY CARRIER OF DAMAGE AT ONCE
Upon receiving of all goods shipped by a Common Carrier, check for any exterior damage
that may indicate interior damage. If conditions permit, open all crates & do a full inspection for
any damage while the delivery driver is still there. If there is damage, please note on the delivery
receipt & call the carrier to make a freight damage claim within 24 hours of receipt. Failure to
make a damage claim within the first 24 hours may void the opportunity to have the claim resolved.
XLT Ovens wants you to be totally satisfied with every aspect of owning & using your
oven & hood. Your feedback, both positive & negative, is very important to us as it helps us understand how to improve our products & our company. Our goal is to provide you with equipment
that we can be proud to build & you can be proud to own.
To receive technical support for the oven or hood you purchased, XLT has qualified customer service personnel that can provide assistance on any type of XLT oven problem you may
experience. Customer Service is available 24/7/365 or visit www.xltovens.com.
Installation of all gas appliances & ventilation exhaust hoods should only be performed by a qualified professional who has read & understands these instructions &
is familiar with proper safety precautions. Read this manual thoroughly before in-
WARNING
stalling or servicing this equipment.
Save this Manual
This document is the property of the owner of this equipment.
XLT Ovens reserves the right to make changes in design & specifications, and/or make additions to or improvements to its product without imposing any obligations upon itself to install
them in products previously manufactured.
All Right Hand & Left Hand designations in this manual are from the point of view as if
standing directly in front of the glass sandwich door.
Revision History Table
Revision Comments Date
A New Release 04/09/2012
Technical Support US: 888-443-2751 Technical Support INTL: 316-943-2751
TABLE OF CONTENTS
Warning & Safety Information..................................................................................................... 2
Warranty ....................................................................................................................................... 4
Oven & Hood Descriptions .......................................................................................................... 8
Oven Dimensions & Weights ..................................................................................................... 10
Oven Gas Requirements ............................................................................................................. 12
Oven Electrical Requirements .................................................................................................... 16
Oven Only Rough-In Specifications .......................................................................................... 17
Oven Assembly .......................................................................................................................... 18
Oven Installation ........................................................................................................................ 23
Oven Fire Suppression ............................................................................................................... 25
Oven Ventilation Requirements & Guidelines ........................................................................... 27
Oven Initial Start-Up .................................................................................................................. 28
Oven Operation .......................................................................................................................... 29
Oven Operator Controls ............................................................................................................. 30
Oven Cleaning ............................................................................................................................ 31
Oven Maintenance ...................................................................................................................... 35
Oven Troubleshooting ................................................................................................................ 36
Hood Description ....................................................................................................................... 39
Hood Dimensions & Weights..................................................................................................... 40
Hood Electrical Requirements.................................................................................................... 42
Hood Electrical Connections ...................................................................................................... 44
Hood Rough-In Specifications ................................................................................................... 57
Hood Exhaust Flow Rates .......................................................................................................... 58
Hood Installation ........................................................................................................................ 60
Hood Initial Start-Up .................................................................................................................. 79
Hood Operator Controls ............................................................................................................. 80
Hood Valance Kit ....................................................................................................................... 81
Hood Duct Wrap Kit .................................................................................................................. 84
Hood Cleaning ............................................................................................................................ 85
Hood Troubleshooting ................................................................................................................ 86
Variable Frequency Drive Manual Mode ................................................................................... 87
Electrical Schematics ................................................................................................................. 88
Certifications .............................................................................................................................. 97
Oven Start-Up Checklist ............................................................................................................ 99
Hood Start-Up Checklist .......................................................................................................... 101
7
Technical Support US: 888-443-2751 Technical Support INTL: 316-943-2751
8
Standard World Standard World
XLT-1832C-S XLT-1832C-W AVI-1832B-S AVI-1832B-W
XLT-2440C-S XLT-2440C-W AVI-2440B-S AVI-2440B-W
XLT-3240C-S XLT-3240C-W AVI-3240B-S AVI-3240B-W
XLT-3255C-S XLT-3255C-W AVI-3255B-S AVI-3255B-W
XLT-3270C-S XLT-3270C-W AVI-3270B-S AVI-3270B-W
XLT-3855C-S XLT-3855C-W AVI-3855B-S AVI-3855B-W
XLT-3870C-S XLT-3870C-W AVI-3870B-S AVI-3870B-W
Hoods
Ovens
This manual covers the following XLT Oven & AVI Hood models:
The first 2 digits of the model number represent the conveyor width and the last two digits
indicate the bake chamber length. The ovens may be used in a single, double, or triple oven stack
configuration. All ovens are gas-fired & are available in Natural gas or LP gas models (Electric
ovens are also available). The 3270 & 3870 models have two burners, one on each side, & have
two control boxes. All other models have only a single burner with a single control box that can
be supplied on either end. All models can be configured for a split belt conveyor.
DESCRIPTIONS
OVEN DESCRIPTION
Food product is placed on the stainless steel wire conveyor belt on one side of the oven.
The conveyor then transports the food through the bake chamber at a user-controlled speed. This
provides repeatable and uniform food cooking. The conveyors can be easily configured to move
either left-to-right or right-to-left. A large center sandwich door allows the introduction or removal of food items for cooking at shorter times. Precise temperatures are user adjustable and
maintained by a digital control.
An easily removable front panel allows the full cleaning of the oven interior. All exposed
oven surfaces both exterior and interior are stainless steel. The conveyor is a one piece design and
is removed from the side which has the control box. No tools are required for disassembly and
cleaning of the conveyor or oven interior. The oven itself is mounted on lockable swivel casters
for easy moving and maintenance.
Accessories such as extended conveyor shelves, base shelves, cool fronts, fire suppression
components, and perforated crumb trays are available from XLT. In addition, moving equipment
such as carts and lifting jacks are available to help install and move ovens. Please contact XLT
Ovens or your Authorized Distributor for more information.
Technical Support US: 888-443-2751 Technical Support INTL: 316-943-2751
OVEN DESCRIPTION
9
Conveyor
Crumb Tray
Front Panel Knob
Sandwich Door
Front Panel
Oven Lid
Control Box
Product Stop
Locking
Swivel Caster
Data Plate
Control Box Lid
Control Switch
Control Panel
Chain Guard
Technical Support US: 888-443-2751 Technical Support INTL: 316-943-2751
10
OVEN DIMENSIONS
Technical Support US: 888-443-2751 Technical Support INTL: 316-943-2751
OVEN DIMENSIONS & WEIGHTS
18
32 47 1/4 70 67 1/4 42 3/4 32
477
[457] [813] [1200] [1778] [1708] [1086] [813] [216]
24 40 53 1/4 78 75 1/4 42 3/4 32
543
[610] [1016] [1353] [1981] [1911] [1086] [813] [246]
32 40 61 1/4 78 75 1/4 42 3/4 32
629
[813] [1016] [1556] [1981] [1911] [1086] [813] [285]
32 55 61 1/4 93 90 1/4 42 3/4 32
757
[813] [1397] [1556] [2362] [2292] [1086] [813] [343]
32 70 61 1/4 110 3/4 105 1/4 42 3/4 32
985
[813] [1778] [1556] [2813] [2673] [1086] [813] [447]
38 55 67 1/4 93 90 1/4 42 3/4 32
829
[965] [1397] [1708] [2362] [2292] [1086] [813] [376]
38 70 67 1/4 110 3/4 105 1/4 42 3/4 32
1077
[965] [1778] [1708] [2813] [2673] [1086] [813] [489]
18
32 47 1/4 70 67 1/4 62 3/4 32 52
863
[457] [813] [1200] [1778] [1708] [1594] [813] [1321] [391]
24 40 53 1/4 78 75 1/4 62 3/4 32 52
981
[610] [1016] [1353] [1981] [1911] [1594] [813] [1321] [445]
32 40 61 1/4 78 75 1/4 62 3/4 32 52
1142
[813] [1016] [1556] [1981] [1911] [1594] [813] [1321] [518]
32 55 61 1/4 93 90 1/4 62 3/4 32 52
1380
[813] [1397] [1556] [2362] [2292] [1594] [813] [1321] [626]
32 70 61 1/4 110 3/4 105 1/4 62 3/4 32 52
1817
[813] [1778] [1556] [2813] [2673] [1594] [813] [1321] [824]
38 55 67 1/4 93 90 1/4 62 3/4 32 52
1513
[965] [1397] [1708] [2362] [2292] [1594] [813] [1321] [686]
38 70 67 1/4 110 3/4 105 1/4 62 3/4 32 52
1984
[965] [1778] [1708] [2813] [2673] [1594] [813] [1321] [900]
18
32 47 1/4 70 67 1/4 67 3/4 17 37 57
1216
[457] [813] [1200] [1778] [1708] [1721] [432] [940] [1448] [552]
24 40 53 1/4 78 75 1/4 67 3/4 17 37 57
1386
[610] [1016] [1353] [1981] [1911] [1721] [432] [940] [1448] [629]
32 40 61 1/4 78 75 1/4 67 3/4 17 37 57
1617
[813] [1016] [1556] [1981] [1911] [1721] [432] [940] [1448] [733]
32 55 61 1/4 93 90 1/4 67 3/4 17 37 57
1964
[813] [1397] [1556] [2362] [2292] [1721] [433] [941] [1448] [891]
32 70 61 1/4 110 3/4 105 1/4 67 3/4 17 37 57
2610
[813] [1778] [1556] [2813] [2673] [1721] [433] [941] [1448] [1184]
38 55 67 1/4 93 90 1/4 67 3/4 17 37 57
2156
[965] [1397] [1708] [2362] [2292] [1721] [433] [941] [1448] [978]
38 70 67 1/4 110 3/4 105 1/4 67 3/4 17 37 57
2846
[965] [1778] [1708] [2813] [2673] [1721] [433] [941] [1448] [1291]
WEIGHT
1832
2440
3240
3255
3270
3855
3870
3270
N/A
3855
N/A
3870
N/A
TRIPLE
STACK
ABCDEFGHJ
WEIGHT
1832
N/A
2440
N/A
3240
N/A
3255
N/A
3855
N/A
N/A
3270
N/A
N/A
DOUBLE
STACK
ABCDEFGHJ
N/A
3240
N/A
N/A
3255
N/A
N/A
3270
N/A
N/A
NOTE: All dimensions in inches [millimeters], ± 1/4 [6], unless otherwise noted. All weights in pounds [kilograms] unless otherwise noted.
SINGLE
STACK
ABCDEFGHJ
WEIGHT
1832
N/A
N/A
2440
N/A
11
Technical Support US: 888-443-2751 Technical Support INTL: 316-943-2751
12
NAT LP
MJ/HR KW/HR
BTU/HR
KW/HR MM MM Inches MM Inches MM
1832 63 17.5 47,700 13.97 3.56 2.24 0.125 3.18 0.081 2.06
2440 79 22.0 67,200 19.68 3.96 2.44 0.144 3.66 0.089 2.26
3240 105 29.2 96,100 28.14 4.62 2.79 0.170 4.32 0.113 2.87
3255 169 47.0 119,900 35.11 5.94 3.66 0.191 4.85 0.116 2.95
3270 190 52.8 140,800 41.23 4.39 2.64 0.144 3.66 0.096 2.44
3855 169 47.0 142,200 41.64 5.94 3.66 0.209 5.31 0.125 3.18
3870 190 52.8 137,900 40.38 4.39 2.64 0.144 3.66 0.096 2.44
Australian
Standard & World
Standard & World
Australian
Gas Oven Heating Values & Orifice Sizes
Oven
Model
All Fuels
NAT
LP
Heating Values
Orifice Sizes
W/C mbar kPa W/C mbar kPa W/C mbar kPa W/C mbar kPa
All 6-14 15-35 1.5-3.5 11.5-14 27.5-35.0 2.75-3.50 3.5 8.75 0.875 10 25 2.5
Natural Gas
LP Gas
Natural Gas
LP Gas
Oven
Models
Gas Oven Fuel Pressure Requirements
Inlet Pressure Range
Manifold Pressure
OVEN GAS REQUIREMENTS
All values shown this page are per each oven
Technical Support US: 888-443-2751 Technical Support INTL: 316-943-2751
OVEN GAS REQUIREMENTS
I
2H
I
2L
I
2E
I
2E+
I
3B/P
I
3+
I
3P
Austria AT X X
Belgium BE X X
Cyprus CY X X X
Czech Republic CZ X X
Denmark DK X X
Estonia EE X
Finland FI X X
France FR X X X X
Germany DE X X X
Greece GR X
Hungary HU X X
Iceland IS
Ireland IE X X X
Italy IT X X
Latvia LT X
Lithuania LV
Luxembourg LU
Malta MT X X
Netherlands NL X X X
Norway NO X
Poland PL X
Portugal PT X X X
Slovakia SK X
Slovenia SI X
Spain ES X X X
Sweden SE X X
Switzerland CH X X X X
United Kingdom GB X X X
Natural Gas (8.75 mbar manifold)
Country
Symbol
Gas Matrix by Country
LP Gas (25 mbar manifold)
Gas Group I2H I2E I
2E+
I2L I3+ I
3B/P (30)
I
3P (30/37/50)
I
3B (37)
Inlet pressure (mbar) 20 20 20/25 25 28/30/37/50 28-30/37/50 30/37/50 37
Number of injectors
Main burner opening size
Ignition
Inlet connection
Fixed
Electric Direct Spark Igniter
BSP 3/4" male thread
World Oven Gas Group
(1) per burner
Natural Gas
Propane Gas
13
Technical Support US: 888-443-2751 Technical Support INTL: 316-943-2751
14
OVEN GAS REQUIREMENTS
Gas Supply Requirements for Australian, Standard. & World Ovens
All installations must conform to local building & mechanical codes.
NOTE
1. The gas supply shall have a gas meter & regulator large enough to handle ALL of the gas ap-
pliances, such as the furnace, water heater, & ovens in operation at the same time. Add up all
of the Btu/kw/MJ ratings to determine the total load.
2. The gas supply shall have a separate gas meter and gas pressure regulator for each occupant.
Installations in multiple occupancy buildings, (strip malls) shall not share gas meters and regulators with other occupants.
3. Gas hose assemblies with quick disconnects for each oven deck will be installed at each valve.
4. A sediment trap shall be installed downstream of the equipment shutoff valve as close to the
inlet of the appliance as practical atr the tiume of appliance installation. The sediment trap
shall be either a tee fitting with a capped nipple in the bottom outlet as illustrated, and in accordance with ANSI Z223.1-2012 and NFPA 54-2012 National Fuel Gas Code, section 9.6.7.
Item # Description
1 1-½ [40] Shut-Off Valve
2 ¾ [20] Shut-Off Valve
3 6 [150] Nipple
4 ¾ [20] Nipple
5 Reducing Tee
6 Tee
7 Cap
8 Plug
All pipe fittings to be 1-½ [40] minimum
unless noted. NPT & BSP
NOTE
CAUTION
1
3
6
3
3
7
Do not use Teflon tape on gas line connections as this can possibly cause gas valve
malfunction or plugging of orifices from shreds of tape. Use of Teflon tape may affect warranty.
4
5
8
4
2
Technical Support US: 888-443-2751 Technical Support INTL: 316-943-2751
OVEN GAS REQUIREMENTS
15
Gas Supply Testing Requirements
1. The appliance & its individual shutoff valve must be disconnected from the gas supply piping
system during any pressure testing of that system at test pressures in excess of 3.5 kPa or ½psi.
2. The appliance must be isolated from the gas supply piping system by closing its individual
manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 3.45 kPa or ½-psi.
Gas Hose Requirements
For Australia, if installing with a flexible hose assembly, the assembly must be certified to
AS/NZS 1869, & be Class B or D.
For Standard Ovens, if installing with a flexible gas hose, the installation must comply with
either ANSI Z21.69 or CAN/CGA-6.16 & a disconnect device complying with either ANSI
Z21.41 or CAN-6.9.
The installation must conform with local building codes, or in the absence of local codes, with
the National Fuel Gas Code, ANSI Z223.1, latest version, Natural Gas Installation Code, CAN/
CGA-B149.1, or the Propane Installation Code, CAN/CGA-B149.2, as applicable.
Technical Support US: 888-443-2751 Technical Support INTL: 316-943-2751
16
Volts AC Amps Hertz Volts AC Amps Hertz
1832 6 3
2440 6 3
3240 6 3
3255 6 3
3270 12 6
3855 6 3
3870 12 6
50
120 VAC
1Φ
60
220/230/
240 VAC
1Φ
Gas Oven Electrical Requirements
Per EACH Oven
Oven
Model
STANDARD
WORLD
OVEN ELECTRICAL REQUIREMENTS
All values shown this page are per each oven
FOR EACH OVEN:
A separate circuit breaker must be provided for each oven deck.
Electrical connections must be accessible when the ovens are in the installed position.
Electrical connections must meet all local code requirements.
Standard Ovens
Electrical Grounding Instructions
This appliance is equipped with a three-prong (grounding) plug for your protection against shock hazard & should be plugged into a properly grounded
three-prong receptacle. Do not cut or remove the grounding prong from this
plug.
When installed, the appliance must be electrically grounded in accordance with lo-
HIGH
VOLTAGE
cal codes, or in the absence of local codes, with the National Electrical Code,
ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.2, as applicable.
World Ovens
This appliance is equipped with a ground lug for your protection against shock
hazard & must be properly grounded.
When installed, the appliance must be electrically grounded in accordance with
local codes.
Technical Support US: 888-443-2751 Technical Support INTL: 316-943-2751
NOTE
OVEN ONLY ROUGH-IN SPECIFICATIONS
6.00 [152]
From back of
oven to wall
17
Utilities must be easily accessible when the ovens are in the installed position. Do not
install utilities behind the ovens.
NOTE
3.00
[76]
6.00
[152]
Electrical Supply
Gas Manifold
48.00
[1219]
42.00
[1067]
All installations must conform to local building and mechanical codes. It is required
that the ovens be placed under a ventilation hood to provide exhaust ventilation and
adequate air supply.
Technical Support US: 888-443-2751 Technical Support INTL: 316-943-2751
18
OVEN ASSEMBLY
Base Assembly - Triple Stack
Technical Support US: 888-443-2751 Technical Support INTL: 316-943-2751
OVEN ASSEMBLY
Base Assembly - Single & Double Stack
19
Technical Support US: 888-443-2751 Technical Support INTL: 316-943-2751
20
OVEN ASSEMBLY
WARNING & SAFETY INFORMATION
XLT ovens can easily be moved and stacked with the proper lifting equipment. The use of
XLT approved lifting equipment is highly recommended. Contact XLT for more information.
These ovens are heavy & can tip or fall causing bodily injury.
NEVER place any part of your body beneath any oven that is suspended by the
lifting jacks. A crush hazard exists if the oven falls or slips.
DO NOT place your hands on the lifting jack vertical pole beneath the jack’s
WARNING
CAUTION
WARNING
winch. As the jack’s winch descends when you turn the jack handle, a pinch
point is created between the winch & the pole.
BE CAREFUL when rolling the oven on the cart, especially when going up or
down ramps & over bumps. Leave the straps/banding on until the oven is near
the assembly area.
Make sure that the notch on tube of the winch assembly is aligned with the pin
in the tripod base as shown. These alignments are important and keep the jack
aligned properly.
Check for smooth operation. The cable should not be pinched and should pass
smoothly over the pulley on top of the pole assembly.
Inspect cable prior to each use.
If cable is frayed or shows signs of excessive wear and tear, DO NOT USE until
cable is replaced.
At a minimum replace the cable annually with wire rope that meets or exceeds
the jack manufacturer’s specifications.
Do not exceed the stated capacity of the jack.
1
Technical Support US: 888-443-2751 Technical Support INTL: 316-943-2751
2
OVEN ASSEMBLY
21
NOTE
The Lifting Pipe hole, marked for the appropriate oven size, must be installed closest
to the control box.
3
Technical Support US: 888-443-2751 Technical Support INTL: 316-943-2751
22
WARNING
WARNING
OVEN ASSEMBLY
Stacking the Ovens
Failure to engage the Lifting Jacks into the Lifting Pipe properly and completely
will result in damage, injury, or death from a falling oven.
Both jacks should be raised in unison, otherwise they may bind and a dangerous
situation will develop.
Do not put any part of yourself under the oven at any time.
The Oven is top heavy. Be careful.
6
5
4
Technical Support US: 888-443-2751 Technical Support INTL: 316-943-2751
OVEN ASSEMBLY
Stacking the Ovens
23
Technical Support US: 888-443-2751 Technical Support INTL: 316-943-2751
24
OVEN INSTALLATION
Physical Location & Spacing Requirements
These ovens are suitable for installation on either combustible or non-combustible floors,
and adjacent to either combustible or non-combustible walls. The motor cover is designed to provide the proper clearance to the back of the oven. The minimum side clearances are 6in. / 150mm,
measured from the end of the conveyor.
All installations must conform to local building and mechanical codes.
NOTE
Restraint
Because all ovens are equipped with casters, all installations must be configured with a restraint to limit the movement of the oven without depending on the electric power supply cord or
gas hose to limit the oven movement. One (1) restraint kit, which includes one (1) eye bolt, (1)
stainless steel clip & a cable, is required for each oven stack, regardless if used on a single, double,
or triple configuration. The clip should be installed in the lowest hole of the back wall on the control end of the lowest oven in the stack. The lag eye bolt must be installed into a structural mem-
ber of a wall or the floor. It is the owner’s responsibility to ensure the restraint is installed cor-
rectly.
Upon completion of performing any service or cleaning functions that require removal of
the restraint, insure that it is correctly re-attached to the oven.
Technical Support US: 888-443-2751 Technical Support INTL: 316-943-2751
1
2
OVEN FIRE SUPPRESSION
The requirement for fire suppression systems vary by location and the authority having jurisdiction. If you are required to install fire suppression on your oven, a pre-assembled piping kit
is available that utilizes pre-existing holes that simplify installation and future service.
25
This design has been tested and approved to successfully comply with fire suppression
codes. It uses only two (2) nozzles per bake chamber, and allows crumb trays, chain guards, and
all other accessories to be easily removed. The kit does not interfere with any operations or maintenance.
A flexible hose that connects the oven to the rest of the fire suppression system is also
available. This allows easy movement of the oven(s) for cleaning and maintenance.
Technical Support US: 888-443-2751 Technical Support INTL: 316-943-2751
26
OVEN FIRE SUPPRESSION
Technical Support US: 888-443-2751 Technical Support INTL: 316-943-2751
OVEN VENTILATION REQUIREMENTS & GUIDELINES
27
Ventilation Requirements
A powered ventilation hood is required to remove heat and vapors. Some provision must
be made to replenish the amount of air that is extracted from the building. The hood and HVAC
installation must meet local building and mechanical codes. Requirements vary throughout the
country depending upon location. Proper ventilation is the oven owner’s responsibility. The AVI
Hood system is designed to meet all requirements for XLT ovens and it is our recommendation
that this system be used.
Ventilation Guidelines
Obtain information from the authority having jurisdiction to determine the requirements for
your installation. Your ventilation hood supplier and HVAC contractor should be contacted to
provide guidance. An air balance test is highly recommended, performed by a licensed contractor.
A properly engineered and installed ventilation hood and HVAC system will expedite approval,
reduce all maintenance costs, and provide a more comfortable working environment. XLT also
recommends that the operator switches for the ovens and the operator switch for the exhaust fan be
interlocked so that the exhaust fan gets energized whenever the ovens are turned on. For more information, see the following links at xltovens.com:
Kitchen Ventilation Design Guide 1
Kitchen Ventilation Design Guide 2
Kitchen Ventilation Design Guide 3
Kitchen Ventilation Design Guide 4
Ventilation Performance Test
After the oven and ventilation hood have been installed and are operating, a smoke candle
can be used to “see” if the heat and vapors are being completely extracted. The test procedure is
outlined below:
The oven must be operating at 450º-500ºF / 232º-260ºC.
The conveyor must be turned off.
The ventilation hood exhaust fan must be turned on.
Put a smoke candle in a pan on the conveyor belt at the center of the oven.
Observe the smoke pattern coming out of the oven.
Repeat the smoke candle test for each oven, as well as when all ovens are operating.
The ventilation hood must capture all of the smoke from the oven.
After the exhaust fan has been adjusted to completely capture and contain the heat, there
needs to be a corresponding amount of make up air (MUA) introduced into the building to offset
the amount of air volume being removed. An air balance test can determine the proper amount of
make-up air flow rates.
Technical Support US: 888-443-2751 Technical Support INTL: 316-943-2751
28
All ovens are tested at the factory for functional operation. Operation is verified and adjustments are made to ensure proper function. However, field conditions are sometimes different
than factory conditions. It is necessary to have an authorized service technician verify operation
and make field adjustments if needed.
The Oven Initial Start-Up Checklist, found at the end of this manual, must be completed
(both sides) at time of installation, signed by the Customer and returned to XLT Ovens and the Authorized Distributor to initiate Warranty Policy.
If the Start-Up Checklist is not filled out completely and returned to XLT Ovens, then the
Warranty will not be honored.
OVEN INITIAL START-UP
Technical Support US: 888-443-2751 Technical Support INTL: 316-943-2751
CAUTION
Oven Operating Temperature Range
Oven
Models
MINIMUM
MAXIMUM
All
400° F
590° F
205° C
310° C
All
Conveyor Belt Times (Min:Sec)
Oven
Models
MINIMUM
MAXIMUM
1:30
17:00
OVEN OPERATION
This oven is not capable of being safely placed in operation in the event of a
power failure. No attempt should be made to operate this oven during power
failure.
Actual Set Point
29
3
1
2
Temperature Control
Push and Hold
4
Conveyor Control
Push and Hold
Technical Support US: 888-443-2751 Technical Support INTL: 316-943-2751
30
OVEN OPERATOR CONTROLS
Conveyor
Speed
Controls
Control Panel Split Belt
Temperature
Control
Circuit
Breakers
Fan &
Filter
Control Panel Standard Belt
Technical Support US: 888-443-2751 Technical Support INTL: 316-943-2751
Loading...