During training, there is a
risk of falling and injury.
Please wear a helmet and
other protective gear in
training process.
Mijia Electric Scooter
First using
1. Place one foot on a
platform of the scooter, an
other must be behind;
2. To bring the scooter to
move, push o from the
oor by another leg, and
then put it behind a leading
leg. Only when both feet
will stand on the scooter
platform, you can press the
speed knob (press the knob
is possible at the minimum
scooter speed of 5km/h);
3. When the turns it`s
necessary to slightly move
a body’s center of gravity in
the right direction, and turn
the steering wheel slowly.
The above information
is intended for those
who are rst learning
to ride a scooter. More
information can be found
in Mijia Electric Scooter
instructions.
1
Safety recommendations
It is forbidden to ride on a
roadway for motor vehicles or
ride in a residential area with
a large ow of passers-by.
Never drive a scooter by
more, than one person, or
with a baby in your arms.
It is forbidden to drive
through the puddles, which
exceeds the depth of 2cm.
It is forbidden to ride a
scooter, without holding
the handlebars.
It is forbidden to ride
a scooter on stairs
or overcome various
obstacles.
Do not ride a scooter in the
rain.
2
Usage
Thank you for choosing this product. Have fun with Mijia Electric Scooter!
Contents
1. The device and accessories....................…………03
2. Functions...………………………………..………….03
3. Assembling.................…………….…………..…….04
4. Charging...................……….………………...……..05
5. Driving instructions.............……………………..….06
6. Safety recommendations...........................……….07
7. Assembling and transportation...…………………. 10
8. Care and storage...……………………………….…11
9. Parameters of the device..............………………...13
10. Presence of toxic and harmful substances...……..13
11. Trade mark and ocials.....................................…13
12. Warranty................................………………………14
2. Functions
Speed lever
Headlight
Brake handle
Folding mechanism
Wheel motor
Control panel
Signal
Clamp
Break lights
Brake disc
Stand
Battery compartment
1. The device and accessories
Vehicle
Instructions Legal information
Short information card
Accessories
Fitting for wheels swap Screws х2
Hex wrench
Power adaptor
Mode indicators
When lowest indicator blinks, battery power will soon completely consumed,
charge the battery. A battery is fully discharged, if indicators is o, and
the vehicle will coast to stop. Lowest charge level indicator may be white
or green. When the vehicle is in normal operation, LED glows white; if
the scooter running in power saving mode, indicator lit green. (In power
saving mode: the maximum speed is 18 km/h, speed lever is adjusted more
smoothly, that is more suitable for beginners).
Charging port
The control panel has 4 LEDs, indicating a level of charge. During consumption of a battery, status indicators are lit, then
ashes and naly o one by another. If all 4 LEDs are lit, a battery level is 100% -86%; if 3 LEDs are lit, and one is blinking,
charge level - 85% -71%; so all charge level lights begin to icker, and then does not light.
3
3. Assembling the device
1) Firmly secure the
steering rack of the vehicle.
Place the scooter on a
stand;
3) On both sides of stearing
rack screw screws by hex
wrench, that come in a
complete set;
2) Set a handle bars
vertical;
4) After assembly, check
operation of the display.
Power button
Press a power button to turn the vehicle. Press and hold a button for 2 seconds to turn o the device. When switched on:
press a power button to turn on/o a ashlight; press a power button twice to switch to normal mode and power saving
mode.
4
4. Charging of the device
While learning to ride a
scooter you can fall and
get hurt. Be sure to wear a
helmet and other protective
gear.
Open the cover of a
charging connector
5. Driving instructions
Insert a power
adaptor plug
After full charging close a
cover tightly
1) Turn on the scooter and
check a charge level;
2) Place one foot on platform of
the scooter, the other must be
behind;
5