Xerox XA7-17i User Manual

©2004 by Xerox Corporation. All rights reserved.

Copyright protection claimed includes all forms and matters of copyrightable material

and information now allowed by statutory judicial law or hereinafter granted, including
without limitation, material generated from the software programs which are displayed
on the screen such as icons, screen displays, looks, etc.

XEROX® and all Xerox product names mentioned in this publication are trademarks

of XEROX CORPORATION. Other company trademarks are also acknowledged.

Changes are periodically made to this document. Changes, technical
inaccuracies, and typographic errors will be corrected in subsequent editions.

2

Xerox© LCD Monitor User’s Manual

Table of Contents

Federal Communications Commission (FCC) Statement ....................3

Important Safety Instructions .................................................................4

1 Introduction

Features ........................................................................................................ 7

Package Contents .........................................................................................8

Front View and Controls ................................................................................9

Installing Your LCD Monitor .........................................................................10

2 Installation

Connecting Your LCD Monitor to a Computer ............................................ 11

Method 1: Analog (D-SUB) Connection .................................................. 11

Method 2: Digital(DVI) Connection .........................................................12

Using Your LCD Monitor ..............................................................................13

3 OSD MENU

Using the OSD Menu ..................................................................................14

The OSD Options ........................................................................................15

4 Technical Information

Preset Mode Timing Chart ...........................................................................18

DVI Connector PIN Assignment .................................................................. 19

D-SUB Connector PIN Assignment .............................................................20

Plug and Play .............................................................................................. 21

Visual Inspection ......................................................................................... 21

Troubleshooting ...........................................................................................22

FCC

ENGLISH

3Xerox© LCD Monitor User’s Manual

This equipment has been tested and found to comply with the limits
of a class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:

1. Reorient/Relocate the receiving antenna.

2. Increase the separation between the equipment
and receiver.

3. Connect the equipment into an outlet on a circuit which is
different from what the receiver is connected to.

4. Consult the dealer or an experienced radio/TV technician

for help.

CAUTION:

Changes or modifications not expressly approved by the
manufacturer responsible for compliance could void the user
authority to operate the equipment.

Federal Communications

Commission (FCC) Statement

Important Safety Instructions

4

Xerox© LCD Monitor User’s Manual

To prevent any injuries, the following safety precautions should
be observed in the installation, use, servicing and maintenance
of this equipment.

Before operating this equipment, please read this manual
completely, and keep it nearby for future reference.

Important Safety Instructions

Warnings

• Do not place the equipment on any uneven or unstable
carts, stands, tables, shelves etc. The equipment may fall,
causing serious injury to children or adults and serious
damage to the equipment itself.

• Use only a cart or stand recommended by the manufacturer.
This equipment and recommended cart or stand should be
handled with care. Quick stops, excessive force, and uneven
surfaces may cause the equipment and cart/stand to
overturn.

• Do not disable the 3-wire grounding type plug. The
grounding pin on the 3-prong plug is an important feature.
Removing the grounding pin will increase the risk of
damaging the equipment. If you can not fit the plug into the
electrical outlet, contact an electrician to install a grounding
outlet.

• Always operate this equipment from the type of power
source indicated on the rear of the serial/model plate.

• Never overload wall outlets and extensions.

• Use and handle the power cord with care.

• Do not place any heavy objects on the AC power cord.

• Do not pull the AC power cord. Do not handle the AC power
cord with a wet hand.

Important Safety Instructions

ENGLISH

5Xerox© LCD Monitor User’s Manual

• Do not touch the power cord and antenna cable during
lightning.

• Remove the plug from the wall outlet if the equipment will
not be used for a long period of time.

• Do not place, use or handle this equipment near water.

• Never expose the equipment to liquid, rain, or moisture.

Seek qualified service if any of the above is spilled into the

equipment.

• Do not attempt to service the equipment yourself.

• Opening and removing the covers may expose you to
dangerous voltage or other hazards and may void your
warranty. Refer service to qualified personnel.

• Always remove the power cord from the outlet before
cleaning the equipment.

• Never use liquid or aerosol cleaners on the equipment.
Clean only with a soft dry cloth.

• Do not expose the equipment to extreme temperature or to
direct sunlight, as the equipment may heat up and suffer
damage.

• Do not install the equipment near any heat sources such as
radiators, heat registers, stoves, or any other apparatus that
might produce heat.

• Do not block any ventilating openings. Leave an open space
around the equipment.

• Never place the equipment :on a bed, sofa, rug, or any other
similar surfaces; too close to drapes/curtains/walls, in a
bookcase, built-in cabinet, or any other similar places that
may cause poor ventilation.

(continued on next page)

Important Safety Instructions

6

Xerox© LCD Monitor User’s Manual

• If any of the following conditions occur, unplug the power
cord from the outlet and request service from qualified
personnel.

a. The power cord or plug is damaged.
b. Liquid is spilled into the product .
c. An object falls onto or into the product.
d. The product has been dropped or damaged.
e. The product’s display is abnormal.

7Xerox© LCD Monitor User’s Manual

Introduction

ENGLISH

• Analog Input: Multi-scanning at horizontal frequencies of
30kHz to 80kHz and vertical frequencies of 60 Hz to 75 Hz.

• Digital Input: Multi-scanning at horizontal frequencies of
30kHz to 64kHz and vertical frequencies of 60 Hz to 75 Hz.

• Microprocessor based with OSD (On Screen Display) control.

• Compatible with standard IBM VGA, extended VGA, super
VGA, IBM XGA modes, as well as VESA resolution
standards.

• Universal power supply.

• Microsoft© Windows 9x/2000/XP compatible and VESA
Display Data Channel(DDC)1/2B compatible.

1 Introduction

Features

8

Xerox© LCD Monitor User’s Manual

Introduction

Make sure all of the following contents are included in the box.
If any items are missing, please return this product to the
original place of purchase.

User Guide

CAUTION:

Be sure to save original box and all packing material for future
transport of monitor.

LCD Monitor

Power Cord* DVI-I to D-SUB

Adapter

* Power cord specification : H05 VV-F 3G 0.75mm

2

Package Contents

9Xerox© LCD Monitor User’s Manual

Introduction

ENGLISH

MENU

Press once to display the OSD (on screen display). And

press to activate the items you highlight .

DOWN/UP

In OSD mode, press the DOWN/UP buttons to move the

selection highlight to the next menu item counterclockwise
or clockwise, respectively.

AUTO

Press to automatically adjust the display settings to optimize

performance based on the VGA signal.

LED

The LED light indicates when the LCD monitor is activated

(blue light indicates power on and blue flash indicates power
saving).

POWER/

Turns the LCD monitor on and off.

Front View and Controls

1 2 3 4 5

1

2

3

4

5

10

Xerox© LCD Monitor User’s Manual

Introduction

Follow the instructions below to set up and install the monitor.

1 The package contains:

1. Display unit

2. Stand

2 Cover an even stable surface with a soft cloth. Place the

unit face-down on the cloth. Fit the stand onto the bottom
of the display unit as shown.

3 Use a coin to tighten the screw on

the bottom of the stand until the
screw is firmly fixed in place.

STANDDISPLAY UNIT

Installing Your LCD Monitor

4

Installation

ENGLISH

11Xerox© LCD Monitor User’s Manual

1 Turn off the computer and unplug the power cable.
2 Fit the DVI-I to D-SUB adapter onto the signal cable of the

LCD monitor.

3 Connect the signal cable to the D-SUB port on the back of

the computer.

4 Connect the AC power cable to the power socket on the

back of the monitor.

5 Plug the computer and monitor power cables into a nearby

outlet.

6 Press the POWER/ button on the front panel of the LCD

monitor to turn the monitor on, then turn the computer on. If
the monitor displays an image, the monitor is successfully
installed. If no image is displayed, check all connections.

Refer to the owner’s manual of the computer for connections.
In the process of connecting external equipment, do not connect
any AC power cords to wall outlets until all other connections
are completed.

5

Connect to
wall outlet

3

2

Attach the
DVI-I to
D-SUB
adapter

4

2 Installation

Connecting Your LCD Monitor to a Computer

Connect to the D-SUB port

Method 1: Analog (D-SUB) Connection

Installation

12

Xerox© LCD Monitor User’s Manual

If the screen displays “out of range”, please follow the
instructions below to set up:

• Press the MENU button to display the OSD.

• Press the UP or DOWN button to highight the (INPUT

SELECT) icon, then press the MENU button. The OSD
displays:

• Press the UP or DOWN button to select DIGITAL INPUT.

1 Turn off the computer and unplug the power cable.
2 Connect the signal cable (DVI-I) to the DVI port on the back

of the computer.

3 Connect the AC power cable to the power socket on the

back of the monitor.

4 Plug the computer and monitor power cables into a nearby

outlet.

5 Press the POWER/ button on the front panel of the LCD

monitor to turn the monitor on, then turn the computer on. If
the monitor displays an image, the monitor is successfully
installed. If no image is displayed, check all connections.

4

2

Connect to the DVI port

3

1

2

1

2

DIGITAL INPUT

Connect to
wall outlet

Method 2: Digital(DVI) Connection

Installation

ENGLISH

13Xerox© LCD Monitor User’s Manual

2 The POWER/ button is used for switching the LCD

monitor on and off, it does not disconnect the device from
the main voltage. To completely disconnect the main voltage,
please remove the power plug from the socket.

-5

o

1 The angle of the LCD monitor may be adjusted

approximately 25 degrees.

POWER/
button

Remove from
wall outlet

20

o

Using Your LCD Monitor

3 The LED indicator is blue when the monitor operates

normally and will flash when in power saving mode. When
the monitor is off, the LED turns dark.

OSD Menu

14

Xerox© LCD Monitor User’s Manual

The OSD (On Screen Display) Menu allows the user to adjust
various settings and options by following the steps below.

1 Press the MENU button to display the OSD.

2 Press the UP or DOWN button to highlight the desired icon.

3 Press the MENU button to activate the highlighted icon.

4 Press the UP or DOWN button to change the value of the

selected item.

5 Select the EXIT icon to exit the OSD.

6 Repeat steps 1 through 5 to make further adjustments. All

changes are stored immediately.

EXIT

Using the OSD Menu

3 OSD MENU

OSD Menu

ENGLISH

15Xerox© LCD Monitor User’s Manual

1 Press the MENU button to display the OSD. The OSD main

menu provides an overview of the selection of controls
available. To make an adjustment to the highlighted setting,
press and release the MENU button.

2 The OSD menu includes the following options:

ON DESCRIPTION

Brightness

Controls the overall brightness.

Contrast

Controls the difference between the brightest and darkest

regions of the picture.

H. Position

Adjust the position of the picture left and right in the window.

V. Position

Adjust the position of the picture up and down in the window.

H.Size

Adjusts the width of the picture.

Phase

Adjusts signal phase, which can improve focus clarity and

image stability.

EXIT

The OSD Options

OSD Menu

16

Xerox© LCD Monitor User’s Manual

Select User Mode

Allows the user to adjust red, green and blue color

component levels independently.

COOL

Inclines colors toward the blue end of the spectrum.

Fixes the red, green and blue component levels at

factory settings; they cannot be independently adjusted.

WARM

Inclines colors toward the red end of the spectrum.

Fixes the red, green and blue component levels at

factory settings; they cannot be independently adjusted.

EXIT

Exits the OSD menu.

Input Select

Allows selection of ANALOG INPUT or DIGITAL INPUT

depending on the type of input signal currently in use.

Color

Allows selection of the general color tint:

Select User Mode, WARM, or COOL.

RED

WARMCOOL

OSD Menu

ENGLISH

17Xerox© LCD Monitor User’s Manual

Reset

Restores all options to the factory settings.

Language

Controls which language is used on all the on-screen menus.

OSD

Changes the position of the OSD.

H. Position

Moves the OSD left and right in the window.

V. Position

Moves the OSD up and down in the window.

EXIT

Exits the OSD menu.

EXIT

Exits the OSD.

Technical Information

18

Xerox© LCD Monitor User’s Manual

The screen image has been optimized during manufacture for
the display modes listed below.

Video signal: (IBM PC/AT)

Dot X Line

Horizontal

Frequency(kHz)

Vertical

Frequency(Hz)

720 x 400 31.47 70.00

640 x 480 31.47 60.00

37.86 72.80

37.50 75.00

800 x 600 35.16 56.25

37.88 60.30

48.08 72.20

46.87 75.00

1024 x 768 48.36 60.00

56.48 70.10

60.02 75.00

1280 x 1024 63.98 60

79.98 75

Preset Mode Timing Chart

4 Technical Information

Technical Information

ENGLISH

19Xerox© LCD Monitor User’s Manual

PIN DESCRIPTION PIN DESCRIPTION

1 TMDS Data 2- 15 GND

2 TMDS Data 2+ 16 Hot Plug Detect

3 TMDS Data 2/4 shield 17 TMDS Data 0-

4 18 TMDS Data 0+

5 19 TMDS Data 0/5 shield

6 DDC Clock 20

7 DDC Data 21

8 Analog Vertical Sync 22 Clock shield

9 TMDS Data 1- 23 Clock +

10 TMDS Data 1+ 24 Clock -

11 TMDS Data 1/3 shield C1 Analog red

12 C2 Analog green

13 C3 Analog blue

14 +5V Power C4 Analog

1 8

169

17 24

C1 C2

C3 C4

DVI Connector PIN Assignment

Technical Information

20

Xerox© LCD Monitor User’s Manual

PIN DESCRIPTION

1 Red

2 Green

3 Blue

4 Ground

5 Self Test

6 Red Ground

7 Green Ground

8 Blue Ground

9 5 VDC

10 Ground

11 Ground

12 SDA (FOR DDC)

13 H. Sync

14 V. Sync

15 SCL (FOR DDC)

1 5

6

11

5

10

1

D-SUB Connector PIN Assignment

Technical Information

ENGLISH

21Xerox© LCD Monitor User’s Manual

Permanently unlit or lit pixels

The standard of production techniques today cannot guarantee
an absolutely fault free LCD display. A few isolated permanently
lit or unlit pixels may be present. The maximum permitted
number of pixel faults is stipulated in the stringent international
standard ISO 13406-2 (Class II).

Example:
A 17” flat-screen monitor with a resolution of 1280 x 1024
has 1280 x 1024 = 1310720 pixels. Each pixel consists of
three subpixels (red, green and blue), so there are about 4
million dots in total.

According to ISO 13406-2 (Class II), a maximum of 6 pixels and
7 subpixels may be defective, i. e. a total of 25 faulted dots. This
corresponds to approx. 0.002 % of the entire screen surface.

Visual Inspection

This monitor conforms to the VESA DDC (Display Data
Channel) standard, which means that when it is used with a
DDC compatible video card, the monitor is easier to set up.
With VESA DDC 1/2B, when the monitor is turned on, it will
automatically notify a windows 9X/2000/XP host computer of its
scanning frequencies, capabilities and characteristics. Windows
9X/2000/XP will automatically recognize the presence of the
monitor and select the appropriate display resolution.

Plug and Play

Technical Information

22

Xerox© LCD Monitor User’s Manual

Before consulting service personnel, check the following
chart for a possible cause and solution to the trouble you are
experiencing.

Monitor will not turn on

• Make sure the power cord is plugged in.

No picture

• Make sure the power cord is plugged in.

• Check the signal cable connecting the LCD monitor

and the computer (refer to page 11).

• Press the POWER/ button on the front panel of the

monitor.

Poor picture or abnormal picture

• Check the DVI cable connecting the LCD monitor and

the computer (refer to page 11).

• Press the MENU button to adjust the Brightness

Contrast option in the OSD.

• Adjust the Color Select option in the OSD.

• Press the AUTO button on the front panel of the

monitor, to automatically adjust the display mode.

Out of range message appears

• Press the MENU button. Highlight the INPUT SELECT

icon, then press the MENU button. Press the UP or

DOWN button to select DIGITAL INPUT

(refer to page 12).

• If using Windows 9X/2000/XP, wait a few seconds;

once Windows detects the problem, a dialog will
appear allowing you to manually set up the video
mode according to the preset mode timing chart

(refer to page 18).

Troubleshooting