Xerox 6115 User Manual

Installation Preparation Document (for physical installation of the product only)

Xerox DocuTech 6100/6115/6135

Customer Support

The Xerox Customer Support Center is available to provide general information, answer questions, and take service calls. You can reach the Customer Support Center at the following toll-free phone number:

United States 1-800-821-2797

Your Xerox Analyst will provide fee-based training upon request.

Space Requirements

The diagram below is provided as a representation only of the space envelope required for installation of Xerox equipment. Diagram is a representation only and not drawn to scale.

DocuT ech 61xx

WIDTH

Representation only.

Note: The 6100, 6115, 6135 are available with and without a stand to

E P T H

support the controller. If a stand is ordered, it will be positioned to the left of the printer, within the service space envelope. If no stand is ordered, the controller will be placed on the floor to the left of the printer in the service space envelope. Note: The dimensions shown below provide the overall service space required, including the space to the nearest obstruction. The dimensions are in inches and are absolute minimums.

Configuration

6100, 6115, 6135

With stand Without stand

Width Depth Width Depth

243.0" 114.0” 240.0” 114.0" with interposer, and Finisher

6100, 6115, 6135

196.0" 114.0” 193.0” 114.0" without Interposer, with Finisher

Electrical Requirements

Printer/Finisher/Binder

Line Options: Single

Source

Voltage 208/240 Amperage 50 Cycles 60 Hz Receptacle Xerox Part No. 600S3779 Receptacle NEMA Part No. 14-50R Power Cord Xerox Part No. 98K19950

117K9940

Receptacle Diagram

* Dedicated power outlets required. Ensure each power cord has a separate

circuit that cannot be shared with other devices. *15 ft. power cord(s) are provided, however, the distance from the equipment to the outlet should not exceed 13.1 ft.

Electrical Requirements

Digital Front End (DFE) Controller Platform:

Line Options: Dedicated

Voltage 110V Amperage 15 Cycles 60 Hz

15 amp Receptacle Xerox Part No. 20 amp Receptacle Xerox Part No.

600S3704 600S3703

Receptacle NEMA Part No. 5 - 20R or 5 - 15R Receptacle Diagram

• All controller configurations require a 110VAC, 15 Amp grounded receptacle for the outlet strip that provides

for the

controller and its peripheral devices (monitor, modem,

receptacles

CDROM drive, and tape drive)

• Adapters that eliminate the ground connection to the outlet can not be used.

• Xerox provides 15 feet of cabling with Teflon coating (Plenum rated), to connect the controller to the Processor/Finisher.

Interposer

Line Options:

Voltage 120 Amperage 15 Cycles 60 Hz Receptacle Xerox Part No. 600S3704 Receptacle NEMA Part No. 5 - 15R Power Cord Length 6 feet Receptacle Diagram

Dedicated

Installation Considerations

• There should be a minimum of 78 inches (1,981mm) clearance from the floor to the nearest overhead obstruction.

• Mobility Assist Device - The optional mobility assist device reduces the installation clearance required to 30 (760mm) at the processor end of the printer and 15 inches (380 mm) at the finisher end.

• For proper operation, the printer must be perfectly level. The floor must be level within 2 degrees in any direction. On floors less than 2 degrees out of level, installation personnel install a leveling kit to level the machine.

• If the floor is more than 2 degrees out of level, this condition cannot be corrected by the leveling kit. Another suitable location must be found for the printer to be installed properly.

• A minimum 50-inch clearance of exclusive operator area must be maintained in front of each component. This space cannot be shared.

• A minimum of 36 inches of clearance is required in the back of each component for general service clearance.

inches

701P43857

June 2005

Please ensure electrical, space, and supplies are available prior to equipment delivery.

Installation Preparation Document (for physical installation of the product only)

Xerox DocuTech 6100/6115/6135

Physical requirements

• The DocuSP Controller Monitor and Keyboard are designed to be positioned on top of the DocuTech 61XX printer. The controller platform is designed to either be mounted in a stand to the left of the printer, or to be positioned on the floor to the left of the printer.

• Warning: Due to safety requirements, under no circumstances should the user interface be visually separated from the printer module. All system installations must enable mobility of the user interface to within 30” (760 mm) of the printer for service and customer maintenance actions

Environmental Requirements

Min. Max.

Temperature 50

F 85 o F * Humidity 30% RH 60% RH Heat Emission - with

Binder On Heat Emission - with

Binder Off Power Consumption

Printer/Finisher w/ Binder

22,165

BTU/Hr

21,265

BTU/Hr

1,330 Watts

(Standby)

14,185 BTU/Hr (With Vent Kits)

13,609 BTU/Hr (With Vent Kits)

5,890 Watts

(Running)

On Power Consumption

Printer/Finisher w/Binder

1,000 Watts

(Standby)

5,630 Watts

(Running)

Off

* The system will inhibit software problems and shut down above 90 o F

Operating Supplies

Reorder No. Impressions / Unit

Dry Ink 6R206 220K/Carton at 6%

area coverage Developer 5R161 750K / Carton Fuser Agent 8R2955 250K / Bottle Stitcher Wire 8R1174 32K / Roll Binder Tape - Black 8R2928 425 Binds / Reel Binder Tape – White 8R3601 425 Binds / Reel Binder Tape – Gray 8R3602 425 Binds / Reel Binder Tape – Blue 8R3603 425 Binds / Reel Binder Tape – Brown 8R3604 425 Binds / Reel Binder Tape – Red 8R3824 425 Binds / Reel

The Xerox Supplies Marketing Center, 1.800.822.2200, is available for ordering Xerox supplies, including paper and other thruput material.

Network Requirements

• The Ethernet interface on the DocuSP controller is a 10/100MB/sec twisted pair standard (10BaseT).

• The Ethernet connection to the DocuSP controller must be compatible with the Institute of Electrical and Electronics Engineers (IEEE) 802.3 standard. (The physical form of this connecter is RJ45 and must be correctly wired.)

• The DocuSP controller supports TCP-IP, SPX,/IPX, and EtherTalk Link Access Protocol (ELAP) protocols if the proper gateways are installed on the controller.

• The DocuSP controller does not provide Novell

Server network services. To use the SPX/IPX protocol, a Novell server installed on the network is required.

• A Xerox Token Ring solution is available for the 61XX family. When Token Ring is installed, it becomes a Token Ring

only connectivity solution. The NetWare gateway and AppleTalk gateway will not function, and the built in Ethernet bge0 twisted pair interfaces are disabled. (Gigabit Ethernet is supported with a Sun controller card – some customers have asked for this option.)

Telephone Requirements

A voice telephone line is required where the DocuTech 6100, 6115, 6135, is installed. Voice line will be used when the operator, administrator, or Xerox Service Personnel is asked to read the screen information from the DocuSP controller dialogs to Xerox Customer Support or Technical Support Center Personnel.

Position / Performance at Maturity

8 7 6

Average

Monthly

Service Calls

3 2 1

300K 1M 2M

500K 1.5M

Average Monthly Copy Volume

Note: This product is targeted for the 300K to 2M copies per month market segment. Usage above this range may result in a higher service frequency

Optimum Range

701P43857

June 2005

Please ensure electrical, space, and supplies are available prior to equipment delivery.