Xantrex Technology 1750, 800, 1500 User Manual
PROWatt 800/1000/1500/1750
Addendum
Owner’s Guide Addendum
This addendum is issued to expand the Ground Fault Circuit Interrupter (GFCI)
outlet features of the PROWatt series products.
The addendum affects the following PROWatt products:
• PROWatt 800 Owner’s Guide (part no. 440-0159 Rev 5)
• PROWatt 1000 Owner’s Guide (part no. 445-0116-01-01)
• PROWatt 1500 Owner’s Guide (part no. 445-0160 Rev 5)
• PROWatt 1750 Owner’s Guide (part no. 445-0117-98-01)
Front Panel (AC End)
This section affects the description of the AC Outlet with Ground Fault Circuit
Interrupter (GFCI) of all the above mentioned PROWatt products.
➃
PROWatt Series
976-0159-01-01 Rev A
LED
ON
OFF
➆
➀
Figure 1
Feature Description
AC Outlet with GFCI (PROWatt 1750 model shown)
➅
➁
AC Outlet. This is a Ground Fault Circuit Interrupter (GFCI) outlet,
equipped with an LED indicator light. The LED comes on when AC power
is interrupted due to a ground fault or an end of life (for the GFCI) fault.
See “Troubleshooting Reference” below.
➂
➄
➅
➆
PROWatt Series
Troubleshooting Reference
This section affects all the above mentioned PROWatt products.
Problem Possible Cause Solution
No output voltage; the
GFCI LED light is on.
No output voltage; the
GFCI LED light is on.
GFCI trip fault, i.e., the
ground fault trip circuit
has been activated.
GFCI end of life fault,
i.e., the GFCI has
permanently ceased to
function.
1. Remove any AC loads.
2. Press the Reset button on the GFCI.
If it trips again a ground fault is present.
3. Turn the inverter off and inspect all wiring for ground
faults.
4. Correct any wiring that could have caused the ground
fault before turning the inverter back on.
5. Press the Reset button on the GFCI, restoring output
voltage.
1. Remove any AC loads.
2. Press the Reset button on the GFCI.
If the Reset button continues to pop out after being pressed,
3. Turn the inverter off and inspect all wiring for ground
faults.
4. Correct any wiring that could have caused the ground
fault before turning the inverter back on.
5. Press the Reset button on the GFCI, restoring output
voltage.
If the above procedure fails to restore power at the AC outlets,
the GFCI has reached its end of life.
6. Take the inverter to the place of purchase and have it
serviced.
Trademarks PROWatt Series is a trademark of Xantrex International. Xantrex is a registered trademark of Xantrex International.
Other trademarks, registered trademarks, and product names are the property of their respective owners and are used herein for
identification purposes only.
Notice of Copyright PROWatt 800/1000/1500/1750 Owner’ s Guide Adden dum © August 2007 Xantrex International. All rights
reserved.
Exclusion for Documentation UNLESS SPECIFICALLY AGREED TO IN WRITING, XANTREX TECHNOLOGY INC. (“XANTREX”)
A) MAKES NO WARRANTY AS TO THE ACCURACY, SUFFICIENCY OR SUITABILITY OF ANY TECHNICAL OR OTHER INFORMATION PROVIDED IN ITS
(
MANUALS OR OTHER DOCUMENTATION.
(
B) ASSUMES NO RESPONSIBILITY OR LIABILITY FOR LOSSES, DAMAGES, COSTS OR EXPENSES, WHETHER SPECIAL, DIRECT, INDIRECT,
CONSEQUENTIAL OR INCIDENTAL, WHICH MIGHT ARISE OUT OF THE USE OF SUCH INFORMATION. THE USE OF ANY SUCH INFORMATION WILL BE
ENTIRELY AT THE USER’S RISK; AND
(C) REMINDS YOU THAT IF THIS MANUAL IS IN ANY LANGUAGE OTHER THAN ENGLISH, ALTHOUGH STEPS HAVE BEEN TAKEN TO MAINTAIN THE
ACCURACY OF THE TRANSLATION, THE ACCURACY CANNOT BE GUARANTEED. APPROVED XANTREX CONTENT IS CONTAINED WITH THE
E
NGLISH LANGUAGE VERSION WHICH IS POSTED AT WWW.XANTREX.COM.
Date and Revision August 2007 Rev A Part Number 976-0159-01-01
Contact Information
Telephone: 1 800 670 0707 (toll free North America) 1 408 987 6030 (direct)
Fax: 1 800 994 7828 (toll free North America) 1 360 925 5143 (direct)
Email: customerservice@xantrex.com Web: www.xantrex.com
2 976-0159-01-01
Loading...