Worx WX682, WX682.9 Instruction manual

SAFETY AND OPERATING MANUAL

ORIGINAL INSTRUCTIONS

Oscillating Tool WX682 WX682.9

1

5

23

4

67

A1 A2

A3

B C1

B

A4

C2

C4

C3

C5

C5

D

E

F

G

- - -

- - -

=

1. ON/OFF SWITCH

2. BATTERY PACK

3. VARIABLE SPEED DIAL

4. UNIVERSAL-FIT ACCESSORY INTERFACE*

5. LED LIGHT

6. SMALLER FLANGE (FOR OTHER BRANDS’

SANDING PADS)

7. FLANGE

Not all the accessories illustrated or described
are included in standard delivery.

*Works with other oscillating tool brands’
accessories.
The following brands are trademarks owned by third
parties which may be registered by their respective
owners: Black & Decker
Craftsman
Imperial Blades, Makita
Performax
Tool Shop

®

, Dremel®, DeWalt®, Fein®, Genesis®,

®

, Porter Cable®, Ridgid®, Ryobi®, Skil®, and

®

.

®

, Bosch®, Chicago Electric®,

®

, Mastercraft®, Milwaukee®,

TECHNICAL DATA

Type WX682 WX682.9 (6-designation of

6

machinery, representative of high frequency
oscillation tool)

WX682 WX682.9

Voltage 20V

No load speed 5000-18000/min

Machine Weight 1.2kg 0.8kg

**Voltage measured without workload. Initial battery
voltage reaches maximum of 20 volts. Nominal
voltage is 18 volts.

Max**

NOISE INFORMATION

A weighted sound pressure LpA: 76dB(A)

A weighted sound power LwA: 87dB(A)

K

pA&KwA

Wear ear protection

3.0dB(A)

VIBRATION INFORMATION

Vibration total values (triax vector sum) deter­mined according to EN 60745:

Typical weighted
vibration

The declared vibration total value may be used for
comparing one tool with another, and may also be
used in a preliminary assessment of exposure.

WARNING: The vibration emission value

during actual use of the power tool can differ
from the declared value depending on the ways in
which the tool is used dependant on the following
examples and other variations on how the tool is
used:
How the tool is used and the materials being cut or
sanded.
The tool being in good condition and well
maintained.
The use the correct accessory for the tool and
ensuring it is sharp and in good condition.
The tightness of the grip on the handles and if any
anti vibration accessories are used.
And the tool is being used as intended by its design
and these instructions.

This tool may cause hand-arm vibration
syndrome if its use is not adequately managed.

WARNING: To be accurate, an estimation of

exposure level in the actual conditions of use
should also take account of all parts of the operating
cycle such as the times when the tool is switched off
and when it is running idle but not actually doing the
job. This may significantly reduce the exposure level
over the total working period.
Helping to minimize your vibration exposure risk.
ALWAYS use sharp chisels, drills and blades.
Maintain this tool in accordance with these
instructions and keep well lubricated (where
appropriate).
If the tool is to be used regularly then invest in anti
vibration accessories.
Avoid using tools in temperatures of 10
Plan your work schedule to spread any high vibration
tool use across a number of days.

Vibration emission value

= 2.615m/s

a

h

Uncertainty K = 1.5m/s²

2

o

C or less.

Oscillating Tool WX682 WX682.9

SAFETY INSTRUCTION FOR
CUTTING

1. Hold power tool by insulated gripping
surfaces, when performing an operation
where the cutting accessory may contact
hidden wiring. Cutting accessory contacting

a “live” wire may make exposed metal parts
of the power tool “live” and could give the
operator an electric shock.

2. Always wear a dust mask.

SAFETY WARNINGS FOR
BATTERY PACK

a) Do not dismantle, open or shred cells or

battery pack.

b) Do not short-circuit a battery pack. Do

not store battery packs haphazardly in
a box or drawer where they may short­circuit each other or be short-circuited
by conductive materials. When battery

pack is not in use, keep it away from other
metal objects, like paper clips, coins, keys,
nails, screws or other small metal objects, that
can make a connection from one terminal to
another. Shorting the battery terminals together
may cause burns or a fire.

c) Do not expose battery pack to heat or

fire. Avoid storage in direct sunlight.

d) Do not subject battery pack to mechanical

shock.

e) In the event of battery leaking, do not

allow the liquid to come into contact
with the skin or eyes. If contact has
been made, wash the affected area with
copious amounts of water and seek
medical advice.

f) Seek medical advice immediately if a cell

or battery pack has been swallowed.

g) Keep battery pack clean and dry.
h) Wipe the battery pack terminals with a

clean dry cloth if they become dirty.

i) Battery pack needs to be charged before

use. Always refer to this instruction and
use the correct charging procedure.

j) Do not maintain battery pack on charge

when not in use.

k) After extended periods of storage, it may

be necessary to charge and discharge
the battery pack several times to obtain
maximum performance.

l) Battery pack gives its best performance

when it is operated at normal room
temperature (20 °C ± 5 °C).

m) When disposing of battery packs, keep

battery packs of different electrochemical
systems separate from each other.

n) Recharge only with the charger specified

by WORX. Do not use any charger other

than that specifically provided for use
with the equipment. A charger that is

suitable for one type of battery pack may create
a risk of fire when used with another battery
pack.

o) Do not use any battery pack which is not

designed for use with the equipment.

p) Keep battery pack out of the reach of

children.

q) Retain the original product literature for

future reference.

r) Remove the battery from the equipment

when not in use.

s) Dispose of properly.

7

Oscillating Tool WX682 WX682.9

SYMBOLS

To reduce the risk of injury, user
must read instruction manual

Warning

Wear ear protection

Wear eye protection

Wear dust mask

Do not dispose of bat teries.

Li-I on

8

Return exhausted batteries
to your local collec tion or
recycling point

Do not expose to rain or water

Do not burn

=

- - -

- - -

xINR18/65-y

High oscillation frequency.

Low oscillation frequency.

LED light is a battery capacity
indicator and will flash when
power gets low .

Waste electrical products
should not be disposed of with
household waste. Please recycle
where facilities exist. Check with
your Local Authority or retailer
for recycling advice.

Cylindrical lithium Ion battery
cells w ith max diame ter of
18mm and ma x height of
65mm ; “x” represents a
number cells s erial c onnected,
blank if 1; “-y” represents a
number of cells paralleled
conne cted, blank if 1.

Avoid danger of injury from the
sharp edges of the accessories.

Accessories can become very
hot while working, presenting
danger of burns!

Make sure the battery is
removed prior to changing
accessories.

Wear protective gloves

Oscillating Tool WX682 WX682.9

OPERATING INSTRUCTIONS

NOTE: Before using the tool, read the
instruction book carefully.

INTENDED USE

The power tool is intended for sawing and
remodeling wooden materials, plastic, plaster, non­ferrous metals and fasteners (e.g. nails and clamps)
as well as for working on soft wall tiles and for dry
grinding of small surfaces. It is especially suitable for
working close to edges and for flush cutting.

ASSEMBLY AND OPERATION

ACTION FIGURE

Mounting Accessories See Fig. A1-A4

Mounting The Sanding Sheet See Fig. B

Mounting The Suction Device (not
supplied)

Operating The On/Off Switch See Fig. D

Using The Variable Speed Dial See Fig. E

Remove Or Install Battery Pack See Fig. F

LED Light See Fig. G

The Variable Speed Dial can be used to set the
optimum oscillating frequency according to the

accessories used and the respective application.

OSCILLATION

FREQUENCY

High oscillation
frequency:

Low oscillation
frequency:

Sanding, sawing, rasping
and polishing stone and
metal.

Scraping, polishing
varnishes.

See Fig. C1-C5

APPLICATION

after you stop working.
Do not start sanding without having the sandpaper
fitted.
Do not allow the sandpaper to wear away , it will
damage the sanding pad. The guarantee does not
cover sanding pad wear and tear.
Use coarse grit paper to sand rough surfaces,
medium grit for smooth surfaces and fine grit for
finishing surfaces. If necessary, first make a test run
on scrap material.
Excessive force will reduce the working efficiency
and cause motor overload. Replacing the accessory
regularly will maintain optimum working efficiency.

MAINTAIN TOOLS WITH
CARE

Your power tool requires no additional lubrication
or maintenance. There are no user serviceable parts
in your power tool. Never use water or chemical
cleaners to clean your power tool. Wipe clean with
a dry cloth. Always store your power tool in a dry
place. Keep the motor ventilation slots clean. Keep
all working controls free of dust. Occasionally you
may see sparks through the ventilation slots. This is

normal and will not damage your power tool.

ENVIRONMENTAL
PROTECTION

Waste electrical products should not be
disposed of with household waste. Please
recycle where facilities exist. Check with your

Local Authority or retailer for recycling advice.

9

WORKING HINTS FOR YOUR
TOOL

If your power tool becomes too hot, especially when
used at low speed, set the speed to maximum and
run it with no load for 2-3 minutes to cool the motor.
Avoid prolonged usage at very low speeds. Always
keep the blade sharp.
Always ensure the workpiece is firmly held or
clamped to prevent movement.
Any movement of the material may affect the quality
of the cutting or sanding finish.
Start your tool before working and turn it off only

Oscillating Tool WX682 WX682.9

APPLICATION

WARNING: The sawing teeth are very sharp. Do not touch during mounting and application.

The workpiece must be clamped tightly before it is cut.

Pic Description Application

Wood, plastic, fiberglass, nails,
non-ferrous metals, thin sheet
metal, hardened fillers

Thin wood, plastic, fiberglass,
non-ferrous metals, thin sheet
metal, hardened fillers, window
glazing

Sawing

Sanding

Universal Metal/Wood End Cut
Blade

Standard Wood End Cut Blade Wood, plastic, drywall

Precision Wood Cut Blade Wood, soft plastics

HSS Semicircle Saw Blade

Sanding Pad (Perforated) Wood, plastic, hardened fillers

10

Rasping

Removing
grout

Scraping

Sanding Finger Pad Wood, plastic, hardened fillers

Triangular Carbide Grit Rasp

Carbide Rasp (Finger Shaped)

Carbide Grit Semicircle Saw Blade

Diamond-Coated Semicircle Saw
Blade

Rigid Scraper Blade

Flexible Scraper Blade

Wood, hardened adhesives, thin
set, masonry

Wood, hardened adhesives, thin
set, masonry

Grout, porous concrete, masonry

Ceramic and stone tile,
backerboard

Old paint, hardened adhesives,
caulk, carpet

Elastic sealants, paint, adhesive
residues, carpet

Oscillating Tool WX682 WX682.9

We recommend that you purchase your accessories
listed in the above list from the same store that sold
you the tool. Refer to the accessory packaging for
further details. Store personnel can assist you and
offer advice.

NOTE: When plunging and sawing use a slight
pendulum motion, to allow sufficient chip removal.
The saw blade lasts longer if the wear is distributed
evenly. To ensure an even distribution, loosen the
saw blade, rotate it and retighten firmly.
Cut/Sand with a constant movement and light
pressure.
Heavy pressure does not increase the cut/removal
rate – the accessory merely wears faster.

DECLARATION OF
CONFORMITY

We,
Positec Power Tools (Europe) Ltd,
PO Box 6242, Newbury, RG14 9LT, UK

Declare that the product
Description WORX Sonicrafter
Type WX682 WX682.9 (6-designation of

machinery, representative of high frequency
oscillation tool)
Function Sanding, sawing, rasping, scraping,
polishing

Complies with the following Directives:

2006/42/EC
2011/65/EU
2014/30/EU

Standards conform to

EN 55014-1
EN 55014-2
EN 60745-1
EN 60745-2-4

The person authorized to compile the technical file,

Name Russell Nicholson
Address Positec Power Tools (Europe) Ltd
PO Box 6242, Newbury, RG14 9LT, UK

®

11

Suzhou 2016/12/12
Allen Ding
Deputy Chief Engineer,Testing & Certification

Oscillating Tool WX682 WX682.9

Warning for WX682:

LITHIUM ION BATTERY

Handle with care.
Do not load or transport package if Damaged.
A fire hazard could exist.
For more information ,call:[phone]

After-sales Service and Application

At www.worx.com you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: 0345 202 9679
E-Mail: [e-mail]

www.worx.com

Copyright © 2016, Positec. All Rights Reserved.
AR01279800