WG791E
P02
P19
Lawn Mowing Robot
Roboter-Rasenmäher
EN
D
Lawn Mowing Robot EN
2
TABLE OF CONTENTS
1. Product Safety
1.1 Safety Warnings for your lawnmower
1.2 Information on the Landroid
®
M
2. Technical Data and Component List
2.1 Technical data
2.2 Component list
3. Understanding Your Landroid®M
3.1 How does my Landroid
®
M know what to mow?
3.2 How does my Landroid
®
M know where to go?
A. Finding the charging base
B. Rain sensors
C. Sensing the boundary wire
D. Starting and stopping while mowing
3.3 How big an area can my Landroid
®
M mow?
3.4 How efficiently will my Landroid
®
M mow the grass?
4. Boundary Wire Basics
4.1 Pegging the Boundary Wire
4.2 Burying the Boundary Wire
4.3 Joining the Boundary Wire
4.4 Turn on and test installation
5. Maintenance
5.1 Keep it Sharp
A. Rotate and Flip the Blades
B. Replace the Blades
5.2 Keep it Clean
A. Cleaning the Body
B. Cleaning the Underside
C. Clean the contact pins and the charging strips
5.3 Battery Life
5.4 Winter Hibernation
5.5 Replacing the battery
6. Declaration of Conformity
3
3
5
7
7
8
10
10
11
11
11
11
11
12
12
13
13
13
13
14
14
14
14
14
15
15
15
15
16
16
17
18
ORIGINAL INSTRUCTIONS
Lawn Mowing Robot EN
3
1. Product Safety
1.1 Safety warnings for your lawnmower
WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious injury.
Carefully read the instructions for the safe operation of the machine.
Save all warnings and instructions for future reference.
•
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
•
Children should be supervised to ensure that they do not play with the appliance.
IMPORTANT
READ CAREFULLY BEFORE USE
KEEP FOR FUTURE REFERENCE
SAFE OPERATION PRACTICES
Training
a) Read the instructions carefully. Make sure you understand the instructions and be familiar with the controls and the
proper use of the appliance;
b) Never allow people unfamiliar with these instructions or children to use the appliance. Local regulations can restrict the
age of the operator;
c) The operator or user is responsible for accidents or hazards occurring to other people or their property
Preparation
a) Ensure the correct installation of the automatic perimeter delineation system as instructed.
b) Periodically inspect the area where the appliance is to be used and remove all stones, sticks, wires, bones, and other
foreign objects.
c) Periodically visually inspect to see that the blades, blade bolts and cutter assembly are not worn or damaged. Replace
worn or damaged blades and bolts in sets to preserve balance.
d) On multi-spindle appliances, take care as rotating one blade can cause other blades to rotate.
e) WARNING! The lawnmower shall not be operated without the guard in place.
OPERATION
1. GENERAL
a) Never operate the appliance with defective guards, or without safety devices, for example deflectors, in place;
b) Do not put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times;
c) Never pick up or carry an appliance while the motor is running;
d) Operate the disabling device from the appliance;
– Before clearing a blockage;
– Before checking, cleaning or working on the appliance;
e) It is not permitted to modify the original design of robotic lawnmower. All modifications are made at your own risk.
f) Start robotic lawnmower according to the instructions. When the main switch is in the ON position, make sure you keep
your hands and feet away from the rotating blades. Never put your hands and feet under the mower.
g) Never lift up robotic lawnmower or carry it around when the main switch is in the ON position.
h) Do not let persons who do not know how robotic lawnmower works and behaves use the mower.
i) Do not put anything on top of robotic lawnmower or its charging station.
j) Do not allow robotic lawnmower to be used with a defective blade disc or body. Neither should it be used with defective
blades, screws, nuts or cables.
k) Do not use robotic lawnmower if the main switch does not work.
l) Always switch off robotic lawnmower using the main switch when you do not intend to use the mower. Robotic
lawnmower can only start when the main switch is moved to the ON position and the correct PIN code has been
entered.
2. ADDITIONALLY WHEN THE APPLIANCE IS OPERATING AUTOMATICALLY
a) Do not leave the machine to operate unattended if you know that there are pets, children or people in the vicinity.
3. ADDITIONALLY WHEN USING THE MANUAL CONTROLLER
a) Mow only in daylight or in good artificial light;
b) Avoid operating the equipment in wet grass;
c) Do not operate the appliance when barefoot or wearing open sandals. Always wear substantial footwear and long trousers;
Lawn Mowing Robot EN
4
d) Always be sure of your footing on slopes;
e) Use extreme caution when reversing the appliance towards you;
f) Always switch on the motor according to instructions with feet well away from the blades(s);
MAINTENANCE AND STORAGE
WARNING! When the mower is turned upside down the main switch must always be set to the
OFF position
The main switch should be set to the OFF position during all work on the mower’s underframe, such
as cleaning or replacing the blades.
a) Keep all nuts, bolts and screws tight to be sure the appliance is in safe working condition;
b) Inspect the robotic lawnmower each week and replace worn or damaged parts for safety;
c) Check especially that the blades and blade disc are not damaged. Replace all blades and screws at the same time if
necessary so that the rotating parts are balanced.
d) Ensure that only replacement cutting means of the right type are used;
e) Ensure that batteries are charged using the correct charger recommended by the manufacturer. Incorrect use may result
in electric shock, overheating or leakage of corrosive liquid from the battery;
f) In the event of leakage of electrolyte flush with water/neutralizing agent, seek medical help if it comes into contact with
the eyes etc;
g) Servicing of the appliance should be according to manufacturers instructions.
Transport
The original packaging should be used when transporting robotic lawnmower over long distances.
To safely move from or within the working area:
a) Press the STOP button to stop the mower. If the anti-theft alarm is activated, enter the first digit of the PIN code. You
select the four digit PIN code when you start the mower for the first time.
b) Move the main switch to the OFF position if you intend to carry the mower.
c) Carry the mower by the handle at the rear under the mower. Carry the mower with the blade disc away from the body.
WARNING! The appliance is only to be used with the unit provided.
Safety warnings for battery pack
a) Do not dismantle, open or shred cells or battery pack.
b) Do not short-circuit a battery pack. Do not store battery packs haphazardly in a box or drawer where they may short-
circuit each other or be short-circuited by conductive materials.
c) Do not expose battery pack to heat or fire. Avoid storage in direct sunlight.
d) Do not subject battery pack to mechanical shock.
e) In the event of battery leaking, do not allow the liquid to come into contact with the skin or eyes. If contact has been
made, wash the affected area with copious amounts of water and seek medical advice.
f) Seek medical advice immediately if a cell or battery pack has been swallowed.
g) Battery pack gives its best performance when it is operated at normal room temperature (20 °C ± 5 °C).
h) When disposing of battery packs, keep battery packs of different electrochemical systems separate from each other.
i) Recharge only with the charger specified by POSITEC. A charger that is suitable for one type of battery pack may create
a risk of fire when used with another battery pack.
j) Under abusive conditions, liquid may be ejected from the battery pack; avoid contact. If contact accidentally occurs,
flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause
irritation or burns.
k) Do not use any battery pack which is not designed for use with the equipment.
l) Dispose of properly.
Lawn Mowing Robot EN
5
1.2 Information on the Landroid®M
WARNING - Robotic lawnmower can be dangerous if incorrectly used.
Read through the Operator’s manual carefully and understand the content before using your robotic
lawnmower.
WARNING - Keep a safe distance from the machine when operating.
WARNING - Operate the disabling device before working on or lifting the machine.
Keep your hands and feet away from the rotating blades. Never place your hands or feet close to or under
the body when robotic lawnmower is in operation.
Robotic lawnmower can only start when the ON/OFF button press ON and the correct PIN code has been
entered. Inspection and /or maintenance must be carried out with the main switch set to OFF.
WARNING - Do not ride on the machine.
Do not burn
Batteries may enter water cycle if disposed improperly, which can be hazardous for ecosystem. Do not
dispose of waste batteries as unsorted municipal waste.
Li-Ion battery. This product has been marked with a symbol relating to ‘separate collection’ for all battery
packs and battery pack. It will then be recycled or dismantled in order to reduce the impact on the
environment. Battery packs can be hazardous for the environment and for human health since they contain
hazardous substances.
Lawn Mowing Robot EN
6
Do not wash the machine with a high pressure washer
Waste electrical products must not be disposed of with household waste. Please recycle where facilities
exist. Check with your local authorities or retailer for recycling advice.
Lawn Mowing Robot EN
7
2. Technical Data and Component List
2.1 Technical data
Type: WG791E (790-799-Designation of machinery, representative of lawn mowing robot)
Rated voltage 28V Max*
No load speed 2800/min
Cutting diameter 180mm
Cutting height 20-60mm
Cutting height positions 5
Battery type Lithium-Ion
Battery model WA3225
Charging time 1.5h approx.
Charger model WA3716
Charger rating
Input: 100-240V~50/60Hz, 50W,
Output: 24-28V dc, 1.5A
Machinery weight 8.9kg
Protection degree IPX4
*Voltage measured without workload. Initial battery voltage reaches maximum of 28 volts. Nominal voltage is 25.2 volts.
Noise and technical data
A weighted sound pressure 44.5dB(A), KPA: 3.25dB(A)
A weighted sound power 63dB(A)
Wear ear protection when sound pressure is over
80dB(A)
Accessories
Charging base with 15m extension cable 1
Blades (WA0176) 12
Screws 12
Wire pegs (WA0179) 200
180m boundary wire 1
Charging base fixing nails 4
Power adaptor (WA3716) 1
Boundary wire distance gauge 2
Hex key 1
We recommend that you purchase genuine accessories listed in the above list from the same store that sold you the tool.
Use good quality accessories marked with a well-known brand name. Refer to the accessory packaging for further details.
Store personnel can assist you and offer advice.
Lawn Mowing Robot EN
8
2.2 Component List
6875
9
10
11
12
23
2221
17
19
16
18
3
4
2
1
25
20
24
15
14
13
Lawn Mowing Robot EN
9
1. HANDLE BAR
2. LOW VOLTAGE CABLE
3. CONTACT PINS
4. CHARGING BASE
5. CHARGING STRIP
6. DISPLAY WINDOW
7. CONTROL PANEL COVER
8. STOP BUTTON
9. RAIN SENSOR
10. REAR DRIVING WHEEL
11. HANDLE
12. BATTERY PACK
13. BLADE TURNING DISC
14. CUTTING BLADE
15. FRONT WHEEL
16. START KEY
17. DISPLAY
18. KEYPAD
19. ON/OFF KEY
20. POWER ADAPTOR
21. BOUNDARY WIRE(150m)
22. WIRE PEGS
23. CHARGING BASE FIXING NAILS
24. BOUNDARY WIRE DISTANCE GAUGE
25. HEX KEY
Lawn Mowing Robot EN
10
3. Understanding Your Landroid®M
We would like to congratulate you on your new purchase of the Landroid®M and entering into the care-free life of automatic
mowing. In the following, we would like to help you better understand how your Landroid
®
M thinks.
3.1 How does my Landroid®M know what to mow?
The Landroid®M chooses its direction at random. It will make sure your entire lawn is evenly mowed without leaving
behind any unattractive mowing paths (See Fig. A).
A
Lawn Mowing Robot EN
11
3.2 How does my Landroid®M know
where to go?
Your Landroid®M is capable of doing things on its own. The
Landroid
®
M knows when it needs to go to its Charging Base (4) to
charge, can sense when it is raining, can stop itself if it senses a
problem, and knows to stop, draw back, and then turn around when
it bumps into something blocking its path, such as a person, pet, or
other object. The Landroid
®
M will also automatically stop its Blade
Turning Disc (13) from rotating if it is lifted off the ground to prevent
an accident.
A. Finding the charging base
When your Landroid
®
M needs to recharge, it will stop mowing and
follow the Boundary Wire (21) in an anti-clockwise motion back to its
Charging Base. Landroid
®
M will automatically stop rotating its Blade
Turning Disc when returning to its Charging Base. However , if it is
required to go back the Charge Base manually ( when you press the
home button), the Blade Turning Disc will rotate and cut the grass
near the boundary wire. So if you want to mow the grass near the
boundary wire, just press the home button. We suggest you use this
function when the battery power is more than 75%. You can check
the battery power in the display.
B. Rain sensors
The Landroid
®
M is fitted with a Rain Sensor (9) that will detect
rain drops and tell the Landroid
®
M to stop mowing and follow the
Boundary Wire back to its Charging Base (See Fig. B )
The Landroid
®
M is programmable to have a delay start function
(0 – 180 mins) when it rains. When the rain sensors are wet, the
Landroid
®
M returns to its docking station. Only when the rain sensors
become dry will the Landroid
®
M begin the delay start countdown or return to mowing immediately. See the Programming
and Troubleshooting Guide for more details.
C. Sensing the boundary wire
The Landroid
®
M always obeys the border set by the Boundary Wire and uses two sensors at its front to sense when it is
getting close(See Fig. C). Before changing direction, the Landroid
®
M will overrun the Boundary Wire up to 20 cm*.
*This is the recommended distance. Use the provided distance gauge to ensure proper installation.
D. Starting and stopping while mowing
If you would like to command the Landroid
®
M to stop mowing, then simply press the STOP button (8) on top of the mower.
To start mowing, open the Control Panel Cover and press the ON/OFF key, then press START key directly or input your
further commands, then press the START key (See Fig. D,E ).
B
C
DD
E
Loading...