Page 1
Hand Dryer Benefits
Planning Guide - pg 2
Airforce™ - pg 3
AirMax™ - pg 4
Hand Dryers
Model A Series - pg 5
Nova® 1 and Nova® 2 - pg 6
Nova® 4 and Nova® 5 - pg 7
NoTouch™, Airspeed
and Electric-Aire™ - pg 8
™
Hair Dryers - pg 9
BACK COVER Baby Changing Stations
Mounting Heights Chart
pg 10
800-323-0701
www.worlddryer.com
Page 2
WHY CHOOSE HAND DRYERS?
Hand Dryers
The benefits of using hand dryers over paper towels
ENVIRONMENTAL
Hand dryers save trees from being cut
down and made into paper towels.
Paper towels can be made from recycled
paper, but they cannot be recycled. They
create millions of cubic feet of waste in
landfills.
The production of paper towels is twice as
energy-intensive as the use of hand dryers
and creates more greenhouse gases.
It takes more energy to produce 2 paper
towels than it does to run a typical high
speed hand dryer.
To make one ton of recycled paper, it takes
7,000 gallons of water, 158 million BTUs of
energy; and 60 pounds of pollutants go into
the atmosphere.
Over its lifetime, just one hand dryer will
produce 3.0 tons less CO2 than the
production of the towels it replaces. (4.6
tons vs 1.6 tons of CO2)
A school using 30 hand dryers saves one
ton, or 17 trees worth of paper towels per
year.
The United States Postal Service identified
hand dryers as the single most cost and
waste reduction alternative in their Pollution
Prevention Study.
FINANCIAL
Hand dryers operate on pennies a day.
Installing hand dryers in public washrooms
reduces hand drying expense by an
average of 90-95% when compared to
paper towels.
The average payback for hand dryers is
12-18 months.
Paper costs continue to rise.
MAINTENANCE
The use of paper towels involves constant
ordering, stocking, cleaning, and disposal.
Hand dryers eliminate paper towel waste
and disposal issues, including plumbing
problems due to clogged paper towels.
SAFETY AND VANDALISM
Paper towels clog toilets, litter floors and
can be fire hazards.
®
World Dryers
Overflowing trash bins are a source for
potential fires.
The cast iron models are literally bullet
proof.
are built to take abuse.
HYGIENIC
Hand dryers are more sanitary than paper
or linen roller towels.
™
The AirForce
SteriTouch anti-microbial additive to protect
from the build-up of germs, mold and
bacteria.
Hand dryers eliminate paper towel waste
and disposal issues.
Dirty towels overflow and liter floors.
Studies have found that hand dryers can
reduce the spread of micro- organisms
compared to paper towels.
Touchless dryer models prevent
contamination of buttons, knobs and levers.
Bacteria laden paper towel waste creates a
negative image for your customer’s
business.
dryers are embedded with
CONVENIENCE
Run out of towels? No worries with hand
dryers.
Hand dryers are always on duty.
2
www.worlddryer.com
Planning Guide
PLANNING GUIDE
The environmentally responsible method to dry your hands
QUANTITY ESTIMATE
Average traffic: 1 dryer per 2 washbasins
Heavy traffic: 1 dryer per washbasin
54” Bradley sink: 4 dryers per sink
DRYER PLACEMENT
Hand dryers should be placed at least 2 feet apart, near but not over the washbasin. In congested areas
dryers should be placed to create a traffic flow from wash basin to dryer to exit. Automatic dryers should be
placed more than 18” above or away from projections, which may interfere with the operation of the
automatic sensor.
More information available online: www.worlddryer.com
AirMax™ XM5-972
Automatic, Surface Mounted
Page 3
MEASUREMENTS
Surface units
Weight
Recessing Kit
Weight
(separate from dryer)
Dryer protrudes 3.5" from the wall with the use of a recessing kit.
625 mm x 337 mm x 76 mm
Shipping
Dimensions
Unit
Measurements
24.6" H x 13.3" W x 3" D
8 lbs / 3.6 kgs
24.9" H x 13.8" W x 5" D
10.7" H x 8.9" W x 6.5" D
7 lbs / 3.18 kgs
Unit
Measurements
Shipping
Dimensions
297 mm x 274 mm x 183 mm
J-970
ELECTRICAL
Aluminum
Surface Mounted
SPECIFICATIONS
Airforce™ Model J, J4, and J48 hand
dryers shall be manufactured by or for
World Dryer® Corporation. Dryer
assembly to be housed in 304 stainless
steel or a die cast Aluminum housing
finished in chrome plating or housing
finished in epoxy paint that is
incorporated with SteriTouch®
antimicrobial additive. Motor shall be
universal brush type operating at 34000
RPM and shall be thermally protected.
Dryer shall be activated by an
automatic active infrared sensor
controlled by a circuit board with 1
second run-on time and 30 second
vandal shut-off. Control board to have
conformal coating. Dryer shall provide a
40°F temperature rise, and PC/ABS
internal housing components to be V0
or V5 flame retardant. Hand dryers shall
be listed under re-examination service
of Underwriters Laboratories, Inc.
INSTALLATION
Airforce™ hand dryers require a
dedicated 15 AMP circuit, and must be
properly grounded. GFI circuit
protection is recommended. One side
of dryer should be mounted to a stud.
™
AIRFORCE
Airforce
Another innovative breakthrough from World Dryer
HAND DRYERS
MODEL NUMBERS
COVER COVER MOUNTING
MATERIAL COLOR OPTIONS Models Models
White Surface J-974 J4-974 J48-974
Black Surface J-162 J4-162 J48-162
Chrome
Brushed J-971 J4-971 J48-971
Stainless
Steel
Steel
RECESSING KIT KJR-973 KJR-973 KJR-973
Stainless Steel, ADA Compliant
Polished
Brushed
White
Surface
Surface
Surface
Surface J-973 J4-973 J48-973
Surface
Volts 120 208/230 220-240
Amps 9.6 4.8 4.8
Watts 1100 1100 1100
Hertz 60 60 50
120 volt
J-970
11.7" H x 10.8" W x 7.2" D
208/230 volt 220-240 volt
J4-970 J48-970
J-972
J-975
272 mm x 226 mm x 165 mm
632 mm x 350 mm x 127 mm
J4-972 J48-972
J4-975 J48-975
Export
®
AIRFORCE
FEATURES
fast 12 second dry
Sound level of
Extremely low
consumption at
infrared activation
ensuring optimum
hygiene levels
reduces the spread
bacteria, mold and
Available with a
white, black or
chrome cover,
surface mounted
or ADA compliant
with a recessed kit
Sleek design
prevents dirt from
collecting and is
easy to clean
WARRANTY
5 year limited
J-974
Surface Mounted
High speed,
time
84.5 dB
power
1100 watts
Automatic
Drastically
of harmful
fungi
™
SURFACE MOUNTED
3/4" KNOCKOUT
FLOOR LINE
Front View Mounting
Side View
(150 mm)
(180 mm)
6.5"
(165 mm)
5.9"
7.1"
6.7"
(170 mm)
RECESS MOUNTED
Front View
Wall Box Mounting
Side View
Drawings not to scale
ENVIRONMENTALLY FRIENDLY
Airforce™ is GreenSpec® listed. Products selected for the GreenSpec list
are considered to be the top of class and environmentally preferable,
based on USGBC Building Green's criteria. Airforce™ can help earn LEED
credits based on EA Credit 1 for optimized energy performance.
Antimicrobial
STERITOUCH® ANTIMICROBIAL
Airforce™ utilizes SteriTouch
SteriTouch® protects from the build-up of germs, mold and bacteria and
makes the dryer easy to clean.
SteriTouch® is an antimicrobial additive designed to reduce the growth of
harmful organisms such as bacteria, mold and fungi, while remaining
entirely safe for even the most sensitive applications.
SteriTouch® is effective against many organisms, including bacteria
such as methicillin resistant staphylococcus aureus (MRSA), escherichia
coli, pseudomonas aeruginosa, salmonella enteritidis and listeria
monocytogenes, and molds such as aspergillus niger.
®
patented anti-bacterial technology.
www.worlddryer.com
3
Page 4
MODEL NUMBERS
Chart shows automatic activation only. For push button, see note below.
COVER COVER MOUNTING 115 volt 208/230 volt 220-240 volt
MATERIAL COLOR OPTIONS Models Models Export
White Surface XM5-974 XM54-974 XM548-974
Beige Surface XM5-468 XM54-468 XM548-468
White Recessed XRM5-Q974 XRM54-Q974 XRM548-Q974
Beige Recessed XRM5-Q468 XRM54-Q468 XRM548-Q468
Steel White Surface DXM5-974 DXM54-974 DXM548-974
Polished Surface DXM5-972 DXM54-972 DXM548-972
Brushed Surface DXM5-973 DXM54-973 DXM548-973
Brushed Recessed DXRM5-Q973 DXRM54-Q973 DXRM548-Q973
Volts 115 208/230 220-240
Amps 20 10 10
Watts 2300 2300 2300
Hertz 60 60 50
ACTIVATION: PUSH BUTTON vs AUTOMATIC
* Push button is not available in Stainless Steel recessed units.
WORLD STONE COVERS
- Available for surface mounted, automatic units only
UNIVERSAL NOZZLES
674- White, 668-Beige, 662-Ebony, 655 Granite Grey
Cast Iron
Stainless
Steel
ELECTRICAL
Example:
M5-974
Use a cast iron model number with the following suffixes:
Example:
XM5-668
AirMax dryers only come with a fixed Universal nozzle.
MEASUREMENTS
Unit Measurements Surface
Recessed
Weight Cast Iron Surface
Cast Iron Recessed
Steel Surface
WorldStone Surface
Shipping Dimensions Surface
Recessed
15" L x 15" W x 11.2" H
11.3" W x 9.6" H x 8.1" D
287 mm x 244 mm x 206 mm
333 mm x 351 mm x 102 mm
13.1" W x 13.8" H x 4" D
29 lbs / 13.15 kgs
35 lbs / 15.88 kgs
381 mm x 381 mm x 284 mm
18 lbs / 8.16 kgs
16 lbs / 7.23 kgs
14.4" L x 12.5" W x 10.1" H
366 mm x 317 mm x 256 mm
DXM5-973
Automatic, Surface Mounted
XRM5-Q974
Automatic, Recess Mounted
M5-974
Push Button, Surface Mounted
AIRMAX™ FEATURES
15 second dry time: twice as fast as
other hand dryers!
™
AIRMAX
Airmax
Models M5, XM5, DM5, DXM5, RM5, XRM5 and DXRM5
HAND DRYERS
The above chart is for automatic activation only. For push button models, remove
the "X" from the model number.
Uses 1/2 the energy per dry of
standard dryers
Sound level of 83.3dB
Available in a variety of cover options,
push button or automatic,
surface mounted or
ADA compliant recessed models
WARRANTY
10 year limited
5 year on sensor
3 year on motor brushes
ENVIRONMENTALLY FRIENDLY
™
AirMax
is GreenSpec
environmentally preferable, based on USGBC Building Green's criteria. AirMax
based on EA Credit 1 for optimized energy performance
®
listed. Products selected for the GreenSpec list are considered to be the top of class and
SPECIFICATIONS
AirMax™ Models M5, XM5, DM5, DXM5, RM5, XRM5 and DXRM5 hand dryers shall be
manufactured by or for World Dryer
with porcelain enamel finish, 14 gauge polished or brushed 304 stainless steel, 14 gauge
epoxy coated Cold Rolled Steel, or 1/4" thick WorldStone Thermoset Polymer. Motor shall
be universal type, 1/6 HP at 12,000 RPM. Dryer shall deliver 238 cubic feet per minute of air
volume (8600 LFM). Timer shall be electromechanical cam style with 25 AMP rated switch
to operate dryer for 20 seconds on push button units. Infrared sensor detects hands, initiates
and terminates drying on automatic units. Recessed units are made with cast iron covers
and use a 16-gauge steel wall mounting box. Hand dryers shall be listed under
reexamination service of Underwriters Laboratories, Inc.
® C
orporation to include a cover of 1/4” thick cast iron
™
can help earn LEED™ credits
™
AIRMAX
Mounting Diagrams
SURFACE MOUNTED
2.5"
(63 mm)
1.5"
(38 mm)
Front View Mounting
and MODEL A MOUNTING DIAGRAMS
RECESS MOUNTED
9.25"
(235 mm)
.87"
(22 mm)
HOLE
8.33"
(212 mm)
7.75"
(197 mm)
12.5"
(315 mm)
1.25"
(32mm)
TYPICAL
Front View - Wall Box Mounting
11.75"
(300 mm)
OPENING
8 KNOCKOUTS 7/8" (22 mm) &
1 1/8" (29 mm) FOR CONDUIT
8 HOLES 13/64" (5 mm)
FOR MOUNTING
Recess Mounted
3.5"
Unit with ADA
Compliant Q Nozzle
(89mm)
(76mm)
3"
4
www.worlddryer.com
Side View
9.5"
(241 mm)
Side View
2.25"
(57mm)
4"
(100 mm)
Drawings not to scale
Page 5
MODEL A SERIES HAND DRYERS
MODEL NUMBERS
Chart shows automatic activation only. For push button, see note below.
COVER COVER MOUNTING 115 volt, 20 amp 115 volt, 15 amp 208/230 volt 277 Volts 220-240 volt
MATERIAL COLOR OPTIONS Models Models Models Models Export
White Surface XA5-974 XA52-974 XA54-974 XA57-974 XA548-974
Beige Surface XA5-468 XA52-468 XA54-468 XA57468 XA548-468
White Recessed XRA5-Q974 XRA52-Q974 XRA54-Q974 XRA57-Q974 XRA548-Q974
Beige Recessed XRA5-Q468 XRA52-Q468 XRA54-Q468 XRA57-Q468 XRA548-Q468
Stamped
Steel
White Surface DXA5-974 DXA52-974 DXA54-974 DXA57-974 DXA548-974
Polished Surface DXA5-972 DXA52-972 DXA54-972 DXA57-972 DXA548-972
Brushed Surface DXA5-973 DXA52-973 DXA54-973 DXA57-973 DXA548-973
Brushed Recessed DXRA5-Q973 DXRA52-Q973 DXRA54-Q973 DXRA57-Q973 DXRA548-Q973
Volts 115 115 208/230 277 220-240
Amps 20 15 10 8.5 10
Watts 2300 1725 2300 2300 2300
Hertz 60 60 60 60 50
ACTIVATION: PUSH BUTTON vs AUTOMATIC
Example:
XA5-668
WORLD STONE COVERS - Available for surface mounted, automatic units only.
All Model A dryers come with a fixed Universal nozzle that can be easily adjusted during installation (or
thereafter) to a swivel nozzle. For specification purposes, a model with a "5" in the model number
(indicating a fixed nozzle) is the same as a model without the "5" (indicating a swivel nozzle).
Example:
order an A5-974 if an
A-974 is specified
UNIVERSAL NOZZLES
Use a cast iron model number with the following suffixes: 674- White, 668-Beige, 662-Ebony, 655 Granite Grey
Cast Iron
Stainless
Steel
ELECTRICAL
Example:
A5-974
The above chart is for automatic activation only. For push button models, remove the "X" from the model number.
* Push button is not available in Stainless Steel recessed units.
Models A5, XA5, DA5, DXA5, RA5, XRA5 and DXRA5
Model A Series
MODEL A FEATURES
Superior engineering and high performance
Sound level of 75 dB
Quality materials provide maximum durability and vandal resistance
XA5-662
Automatic Surface Mounted
XRA5-Q974
Automatic Recess Mounted
A5-974
Push Button Surface Mounted
Available in a variety of cover options, push button or automatic, surface
Universal nozzle is shipped fixed and is easily convertible to swivel
mounted or ADA compliant recessed models
WARRANTY
10 year limited, 5 year on sensor, 3 year on motor brushes
FOR AIRMAX™ and MODEL A SERIES
Cover Options
CAST IRON COVERS
Cast Iron provides the ultimate in durability and vandal-resistance. The
1/4” thick cast iron with porcelain enamel construction makes this option
suitable for areas such as train/bus stations, schools, theaters, airports,
and prisons.
STEEL COVERS
They are both durable and economical. Grade 304 stainless steel
covers are vandal resistant and offer a touch of elegance.
WORLD STONE COVERS
Provide a durable, cost effective option to traditional metal covers.
Available for Model A and AirMax
dryers. Embedded with antimicrobial agents to promote hygiene.
Material originally developed for use in high temperature, demanding
aerospace and automotive applications.
COVER MATERIALS
White
™
, surface mounted, automatic hand
Beige
Ebony
Granite Grey
SPECIFICATIONS
Models A5, XA5, DA5, DXA5, RA5, XRA5 and DXRA5 hand dryers
shall be manufactured by or for World Dryer Corporation
cover made of 1/4” thick cast iron with porcelain enamel finish, 14
gauge polished or brushed 304 stainless steel, 0.08” thick epoxy
674
coated Cold Rolled Steel, or 1/4” thick WorldStone Thermoset Polymer.
Motor shall be universal type, 1/10 HP at 7500 RPM. Dryers shall
deliver 154 cubic feet per minute of air volume (7300 LFM). Timer shall
be electromechanical cam-style with 25 AMP rated switch to operate
dryer for 30 second period on push button units. Infrared sensor
detects hands, initiates and terminates drying on automatic units.
668
Recessed units are made with cast iron or 304 stainless steel covers
and use a 16-gauge steel wall mounting box. Hand dryers shall be
listed under reexamination service of Underwriters Laboratories, Inc.
INSTALLATION
662
AirMax™ and Model A hand dryers require a dedicated 20 AMP circuit,
and must be properly grounded. GFI Circuit protection is
recommended. One side of dryer should be mounted to a stud.
655
®
to include a
www.worlddryer.com
5
Page 6
MODEL NUMBERS
COVER MOUNTING 120 volt
COLOR OPTIONS Models
White Surface 0930
Brushed
Stainless Steel
Volts 120, 208-240
Amps 15, 10
Watts 2300
Hertz 60 or 50
ELECTRICAL
Surface
093079
MEASUREMENTS
Unit Measurements
Weight
Shipping Dimensions
406 mm x 330 mm x 203 mm
356 mm x 254 mm x 100 mm
14" W x 10" H x 4" D
12 lbs / 5.5 kgs
MODEL NUMBERS
Surface Mounted Surface Mounted
Hard wired Plug-in
0830 0833
White White
Volts 120, 208-240 120
Amps 8,7 8
Watts 1000 1000
Hertz 60 or 50 60
MEASUREMENTS
Unit Measurements
Weight
Shipping Dimensions
MOUNTING
OPTIONS
Cover Color
Model Number
ELECTRICAL
9.0" W x 9.7" H x 4" D
330 mm x 305 mm x 203 mm
13" L x 12" W x 8" H
10 lbs
/ 4.55kgs
NOVA 1
®
NOVA 1
FEATURES
Surface mounted,
automatic
activation, and
ADA compliant
Nova 1® is
multi-voltage
(100 VAC to 240
VAC), Nova 1®
Plug-in works on
120 volt
Thermally
protected motor,
tamper resistant
Nova 1® Plug-in
offers hassle free,
quick installation
screws
®
HAND DRYERS
®
Nova 1
traffic areas and are quiet.
and Nova 1® Plug-in hand dryers are suitable for light
228 mm x 246 mm x 100 mm
Nova 1® - 0830
Automatic Surface Mounted
Nova 1® Plug-in - 0833
Automatic Plug-in Mounted
Nova Series
SPECIFICATIONS
Nova 1® hand dryers shall be manufactured by or for
®
Hand Dryers to include cover of die cast Aluminum
Nova
with white epoxy enamel. Motor shall be thermally
protected brush type with minimum 7500 RPM with a
single shaft. Dryer shall deliver 134 cubic feet per minute
of air volume (6400 LFM), and shall be activated by an
infrared sensor, and controlled by a microprocessor that
allows multi-voltage application (100 VAC to 240 VAC 50 or 60 Hz). Dryer shall be surface mounted, and Nova
®
must not protrude more than 4 inches from the wall
1
when hard-wired. Plug-in units shall be equipped with a 6
foot long cord and three-prong conductor plug, and shall
include mounting bracket and hardware. Plug-in units
available only in 120 VAC, 60 Hz for use with common
wall outlets. Nova
reexamination service of Underwriters Laboratories, Inc.
®
Hand Dryer shall be listed under
Sound level
of 76dB
WARRANTY
2 year limited
Rear Mounting Front View Side View
®
NOVA 2
NOVA 2®
FEATURES
Surface mounted,
automatic
activation
Thermally
protected motor,
tamper resistant
screws
Nova 2® has dual
blowers for
maximum output
Sound level of
74dB
WARRANTY
5 year limited
6
www.worlddryer.com
HAND DRYERS
Nova 2
VAC to 240 VAC) that are suitable for light traffic
areas and are quiet.
®
hand dryers are multi-voltage units (100
16" L x 13" W x 8" H
Rear Mounting
Rear Mounting
Nova 2® - 0930
Automatic Surface Mounted
Front View
Side View
Nova Series
SPECIFICATIONS
Nova 2® hand dryers shall be manufactured by or for Nova® Hand Dryers to include
cover of drawn steel with porcelain enamel or drawn brushed finish 304 stainless
steel. Motor shall be thermally protected brush type with minimum 7500 RPM with
double shaft. Dryer shall contain dual blowers and deliver 220 cubic feet per minute of
air volume (5300 LFM), and shall be activated by an infrared sensor, and controlled by
a microprocessor that allows multi-voltage application (100 VAC to 240 VAC - 50 or
60 Hz). Dryer shall be surface mounted. Nova
reexamination service of Underwriters Laboratories, Inc.
INSTALLATION
Nova® hand dryers require a dedicated 20 AMP circuit, and must be properly
grounded. GFI Circuit protection is recommended. One side of dryer should be
mounted to a stud.
®
Hand Dryers shall be listed under
Page 7
MODEL NUMBERS
COVER MOUNTING 120 volt 208/240 volt 120 volt
COLOR OPTIONS Models Models Inst. Model *
White Surface 0412 0422 0512
White Recessed 0712 0722
Volts 120 208/240 120
Amps 15 7.5 15
Watts 1800 1800 1800
Hertz 60 60 60
MEASUREMENTS
Unit Measurements Surface
Recessed
Weight Surface
Recessed
Surface
Recessed
14" L x 11" W x 13" H
ELECTRICAL
Shipping Dimensions
12" W x 8" H x 5.9" D
305 mm x 203 mm x 150 mm
27 lbs / 12.27 kgs
22 lbs / 10 kgs
MODEL NUMBERS
COVER ACTIVATION 120 volt 208/240 volt
COLOR Models Models
White Push Button 0112 0122
Chrome Push Button 011299 012299
Chrome Automatic 011299 022299
Volts 120 208/240
Amps 15 7.5
Watts 1800 1800
Hertz 60 60
RECESSED KIT
White Trim 37-058500
Steel Box
Chrome Trim 37-058589
ELECTRICAL
MEASUREMENTS
Surface
Recessed
Weight Surface
Recessed
Surface
Dryer and
406 mm x 406 mm x 100 mm
330 mm x 254 mm x 279 mm
Shipping Dimensions
13" L x 10" W x 11" H
15" W x 13.2" H x 5.9" D
18 lbs / 8.18 kgs
29 lbs / 13.2 kgs
Unit Measurements
®
NOVA 4
HAND DRYERS
The Nova 4® hand dryer is durable and vandal resistant. These hand dryers are available
for surface or recessed mounting.
* Institutional model includes top knockout for surface wiring installation.
12.3" W x 9.2" H x 9.3" D
312 mm x 234 mm x 236 mm
356 mm x 279 mm x 330 mm
14" L x 11" W x 13" H
356 mm x 279 mm x 330 mm
®
NOVA 5
HAND DRYERS
The Nova 5® hand dryer is available in surface mounted with an optional recessing
kit. The push button model is available with an adjustable timing feature.
White Automatic 0212 0222
®
Nova 4
Push Button, Surface Mounted
- 0412
Nova Series
NOVA 4® and NOVA 5
®
Nova 5
Push Button, Surface Mounted
- 0112
®
FEATURES
Low amperage, quiet induction motor
Sound level of 74dB
Motor is brushless, so no need for brush replacement
Durable and vandal resistant.
WARRANTY
10 year limited, 5 year on sensor
SPECIFICATIONS
®
& Nova 5
Nova 4
for Nova
constructed of .20” thick cast iron (Nova 4
acid-resistant porcelain enamel or .09” thick die cast aluminum
finished in brushed chrome plating or epoxy coating (Nova 5
Dryers shall be fitted with 360 degree revolving die cast
aluminum nozzles finished in bright chrome plating.
Surface-mounted covers shall be fastened by two flat- head,
recessed tamper-resistant bolts to a heavy-gauge steel wall
plate, which in turn shall be fastened to the wall or a wall box by
four concealed mounting bolts. (For recessed dryers only: A
steel wall box shall be furnished into which a complete base
assembly shall be mounted). The dryer shall be equipped with
15 air intake slots (Nova 4
The fan shall be protected by an aluminum die cast grating fixed
into the blower housing. The entire mechanism shall be
internally grounded throughout. The motor shall be brushless,
1/10 H.P., 3200 RPM, thermally protected. The fan shall be a
large single inlet centrifugal type contained in an aluminum die
cast housing. It shall deliver 107 cubic feet per minute of air
volume (4400 LFM) and shall be mounted directly on the motor
shaft. The heating element of nichrome wire shall be mounted
on the air intake. It shall be protected by an automatic resetting
circuit breaker (25 AMP) which shall open whenever the air flow
is cut off and shall close when the flow of air is resumed. The
element shall produce an air temperature of 142 F at a 72 F
ambient room temperature. The dryer shall be equipped with an
infrared sensor which will allow the dryer to start automatically
when hands are placed underneath the air nozzle, and to stop
automatically when the hands are removed. For push button
dryers (Nova 5
micro-switch activated. It shall be adjustable to allow for the
required time cycle setting. Nova
under reexamination service of Underwriters Laboratories, Inc.
®
®
hand dryers shall be manufactured by or
Hand Dryers to include a one-piece cover
®
) or 30 air intake slots (Nova 5®).
®
only), timer shall be micro-chip based and
®
®
) finished in white
Hand Dryers shall be listed
®
).
Recessed Unit
12" W x 8.7" H x 9.3" D
305 mm x 221 mm x 236 mm
381 mm x 335 mm x 150 mm
16" L x 16" W x 4" H
www.worlddryer.com
7
Page 8
MEASUREMENTS
Shipping Dimensions
330 mm x 305 mm x 203 mm
10.7" H x 11.6" W x 4.9" D
13" L x 12" W x 8" H
10 lbs / 4.55 kgs
273 mm x 294 mm x 124 mm
Unit Measurements
Weight
MODEL NUMBERS
BODY ACTIVATION 120 volt, 17 amp 120 volt, 13 amp 208/240 volt 220-240 volt
COLOR Models Models Models Export
White Automatic NT126-005 --- NT246-005 NT235-005
Chrome Automatic NT126-004 --- NT246-004 NT235-004
White Push Button WA126-002 WA126-202 WA246-002 WA235-002
Chrome Push Button WA126-001 WA126-201 WA246-001 WA235-001
Volts 120 120 208/240 220-240
Amps 17 13 8.5 8
Watts 2000 1500 2000 1800
Hertz 60 60 60 50
RECESSING KIT KNTR-973 KNTR-973 KNTR-973 KNTR-973
Stainless Steel
ELECTRICAL
MEASUREMENTS
Unit Surface
Measurements
Recessed
Weight Surface
Recessed
Shipping Surface
Recessed
22 lbs / 10 kgs
31 lbs / 14.09 kgs
™
MOUNTING
OPTIONS
Cover Color
Model Number
ELECTRICAL
NO TOUCH
The No Touch™ and Airpseed™ hand dryers are designed for lighter traffic areas. The quiet induction motor is brushless - no need to replace brushes!
™
No Touch
Automatic, Recess Mounted
NT
with KNTR Recess Kit
& AIRSPEED™ HAND DRYERS
No Touch
SPECIFICATIONS
™
Airspeed
Push Button, Surface Mounted
NO TOUCH
AIRSPEED™
Tamper resistant screws lock cover
securely to base
Resilient motor mounting rings and
factory-lubricated, self-aligning
bearings for long motor life
Dynamically balanced blower
wheel for vibration-free running
Thermal shut-off safety features
controlled by an internal thermostat
Sound level of 71dB
Designed for light traffic
or noise sensitive areas
WA
™
and
FEATURES
WARRANTY 5 year limited
10.9" W x 11.6" H x 7.5" D
277 mm x 295 mm x 191 mm
12.7" W x 13.5" H x 5.5" D
323 mm x 343 mm x 140 mm
13" L x 12" W x 9.5" H
Dimensions
330 mm x 305 mm x 241 mm
16" L x 15" W x 14" H
406 mm x 381 mm x 356 mm
12.5”
INSTALLATION
Hand dryers require a dedicated 20 AMP circuit, and must be properly grounded. GFI Circuit protection is recommended.
One side of dryer should be mounted to a stud.
Airspeed™ and No Touch™ hand dryers
shall be manufactured by or for World
®
Corporation to include housing
Dryer
of .08“ thick die cast aluminum. Front
panel shall be in ebony gloss for the
™
NoTouch
the Airspeed
with chrome plating or white epoxy
paint. Motor shall be of shaded pole
(brushless) type operating at maximum
3200 RPM at rated load, delivering 120
cubic feet per minute of air volume
(5300 LFM). Timer shall be
electromechanical cam style with 25
amp rated switch to operate dryer for 30
seconds on push button units. No
Touch
means of an infrared emitting/ receiving
electronic control device. Recessed kits
will include a 16 gauge steel
wall-mounting box. Hand dryers shall
be listed under reexamination service of
Underwriters Laboratories, Inc.
and brushed aluminum for
™
. Housing to be finished
™
dryers shall be activated by
ELECTRIC-AIRE™ LE HAND DRYERS
Electric-Aire
LE hand dryers are suitable for light traffic areas and are quiet.
LE FEATURES
Surface mounted, automatic
activation
Multi-voltage (100 to 240 VAC)
Thermally protected motor,
tamper resistant screws
Sound level of 76dB
WARRANTY
2 year limited
Electric-Aire LE5-974
8
www.worlddryer.com
SPECIFICATIONS
LE hand dryers shall be manufactured by or for World Dryer
to include cover of die cast Aluminum with white epoxy
enamel. Motor shall be thermally protected brush type with
minimum 7500 RPM with a single shaft. Dryer shall deliver
134 cubic feet per minute of air volume (6400 LFM), and
shall be activated by an infrared sensor, and controlled by a
microprocessor that allows multi-voltage application (100
VAC to 240 VAC - 60 Hz). Dryer shall be surface mounted.
Hand Dryer shall be listed under reexamination service of
Underwriters Laboratories, Inc.
"
6.95
(177 mm)
10.73"
(273 mm)
(162 mm)
6.38
"
(109 mm)
2.38"
(60 mm)
"4.29
4.90"
(124 mm)
11.59"
(294 mm)
MODEL NUMBERS
Surface Mounted
Hard wired
LE5-974
White
Volts 120, 208-240
Amps 8,7
Watts 1000
Hertz 60
Page 9
MEASUREMENTS
Weight
Unit Measurements
Shipping Dimensions
6 lbs / 2.73 kgs
Models
HD3
Volts 110-120
Amps 9.1
Watts 1000
Hertz 60
Connection
MODEL NUMBERS
COVER COVER MOUNTING 115 volt, 20 amp 115 volt, 15 amp 208/230 volt 277 Volts 220-240 volt
MATERIAL COLOR OPTIONS Models Models Models Models Export
White Surface B-974 B1-974 B3-974 B7-974 B38-974
Beige Surface B-468 B1-468 B3-468 B7468 B38-468
White Recessed RB-974 RB1-974 RB3-974 RB7-974 RB38-974
Beige Recessed RB-468 RB1-468 RB3-468 RB7-468 RB38-468
Stamped Steel White Surface DB-974 DB1-974 DB3-974 DB7-974 DB38-974
Polished Surface DB-972 DB1-972 DB3-972 DB7-972 DB38-972
Brushed Surface DB-973 DB1-973 DB3-973 DB7-973 DB38-973
Volts 115 115 208/230 277
220-240
Amps 20 15 10 8.5 10
Watts 2300 1725 2300 2300 2300
Hertz 60 60 60 60 50
ACTIVATION:
The Model B is only available with push button activation
Cast Iron
Stainless Steel
ELECTRICAL
MEASUREMENTS
Surface
Weight Cast Iron Surface
Cast Iron Recessed
Steel Surface
Recessed
287 mm x 244 mm x 206 mm
35 lbs / 15.88 kgs
18 lbs / 8.16 kgs
Unit Measurements
Shipping Dimensions
29 lbs / 13.15 kgs
Cord and ALCI Plug
ELECTRICAL
Airstyle
AIRSTYLE
The Airstyle
second drying cycle. Designed for use in health clubs, locker rooms, and schools.
Recessed
Surface
1
1
"
2
7
8
"
3
4
7
(197 mm)
(38 mm)
"
HOLES
(22 mm)
1
9 "
4
(235 mm)
SURFACE MOUNTED
FLOOR LINE
2
(63 mm)
1
"
2
™
MODEL B HAIR DRYERS
™
hair dryers feature a safe and energy efficient, high powered 80
SPECIFICATIONS
Airstyle™ Model B Series
11.3" W x 9.6" H x 8.1" D
13.18" W x 13.8" H x 4" D
335 mm x 351 mm x 102 mm
14.4" L x 12.5" W x 10.1" H
366 mm x 317 mm x 256 mm
15" L x 15" W x 11.2" H
381mm x 381 mm x 284mm
9.5 (241 mm)
)
)
m
m
m
m
3
3
2
5
3
3
(
(
9
7
.
.
2
3
1
1
6.1 (155 mm)
SIDE
VIEW
(307 mm)12.1
(333 mm)13.1
RECESS
MOUNTED
industrial hair dryers shall be
manufactured by or for World
®
Corporation to include a
Dryer
1/4” thick cast iron with porcelain
enamel, 14 gauge thick epoxy
coated Cold Rolled Steel, or 14
gauge thick polished or brushed
304 stainless steel. Motor shall
be of universal type, 1/10 hp at
7500 RPM. Dryer shall deliver
154 CFM (7300 LFM) of warm air
volume. Dryers shall be activated
by means of a push button
control device. Timer shall be
cam operated electro-mechanical
type, designed to operate the
hair dryer for no less than 80
seconds after activation. Chrome
plated nozzle to revolve 360
degrees. Recessed units will
include a 16-gauge steel
wall-mounting box. Hair dryer
shall be listed under the
reexamination service of
Underwriters Laboratories, Inc.
INSTALLATION
Airstyle™ hair dryers require a dedicated 20 AMP circuit, and must
be properly grounded. GFI Circuit protection is recommended. One
side of dryer should be mounted to a stud.
™
Airstyle
Push Button, Surface Mounted
B-974
AIRSTYLE™ FEATURES
Push button dryer features a safe
and energy efficient, high
powered 80 second drying cycle
Available in surface or recessed
mounted
Provides a convenient amenity
that is highly vandal-resistant
All models feature swivel
nozzles
Sound level of 74dB
WARRANTY
10 year limited
110-120 volt
WorldWind
WORLDWIND™ HAIR DRYERS
MODEL NUMBERS
8" H x 23.5" W x 4" D
203 mm x 597 mm x102 mm
19" L x 8.5" W x 4.8" H
483 mm x 216 mm x 122 mm
For lighter use applications, the WorldWind™ hair dryer is a wall-mounted unit
that isolates electrical components from accidental water contact. Recommended
for hotels, hospitals, and nursing homes.
SPECIFICATIONS
WorldWind™ models HD3 shall
include a flexible hose
permanently attached to direct
air flow. Unit shall be equipped
with variable temperature drying
and shall deliver 45 CFM of air
volume at maximum rated
voltage. Plug shall have ALCI
protection. Unit to be listed
WorldWind™ HD3
Surface Mounted
under the reexamination service
of Underwriters Laboratories, Inc
www.worlddryer.com
WORLDWIND™
FEATURES
Delivers 1,000 watts of power
Variable temperature control
Safety timer automatically
activates when hand piece is
removed
WARRANTY
One year
9
Page 10
MODEL NUMBERS
ABC-300H ABC-300V ABC-300HS ABC-300HSR
Horizontal Vertical Horizontal Horizontal
Surface Surface Surface Recessed
Body Polyethylene Polyethylene
Exterior Brushed Stainless Steel Brushed Stainless Steel
457 mm x 876 mm 864 mm x 483 mm 546 mm x 953 mm 864 mm x 483 mm
100 mm x 432 mm 140 mm x 866 mm 100 mm x 432 mm 3 mm x 457 mm
Weight 15.5 lbs / 7 kgs 20.5 lbs / 9.3 kgs 35 lbs / 15.9 kgs 32 lbs / 14.5 kgs
Shipping Dimensions 36" L x 19" W x 6" H 36" L x 20" W x 6" H 48" L x 27" W x 7" H 41" L x 27" W x 7" H
914 mm x 483 mm x 152 mm 914 mm x 508 mm x 152 mm 1219 mm x 686 mm x 178 mm 1041 mm x 686 mm x 178 mm
Polyethylene
Polyethylene
MOUNTING
closed / open
MATERIAL
BABY CHANGER
Surface Recess Airstyle
™
WorldWind
™
DryBaby
™
Men 46" (117cm) 42" (107cm) 68" (172cm) 58" (147cm) 34" (86cm)
Women 44" (112cm) 40" (102cm) 59" (150cm) 58" (147cm) 34" (86cm)
Disabled 37" (94cm) 34" (86cm) 40" (102cm) 38" (86cm) 34" (86cm)
ages 3-7 32" (81cm) 28" (71cm) 41" (104cm) 58" (147cm) 34" (86cm)
ages 8-10 36" (91cm) 32" (81cm) 48" (122cm) 58" (147cm) 34" (86cm)
ages 11-13 40" (102cm) 36" (91cm) 54" (132cm) 58" (147c
m) 34" (86cm
)
ages 14-17 44" (116cm) 40" (102cm) 59" (150cm) 58" (147cm) 34" (86cm)
HAND DRYERS
HAIR DRYERS
CHILDREN
ADULTS
™
DRYBABY
DryBaby
Unit Measurements 18" H x 34.5" W 34" H x 19" W 21.5" H x 37.5" W 18" H x 34.5" W
™
DRYBABY
polyethylene interior
Safety belt adjustable
No buckle to catch
Built-in liner dispenser
Bag hooks on both sides
for added convenience
FEATURES
Easy-to-clean
Horizontal Mounted
with one hand
and break in door
WARRANTY
5 year limited
The DryBaby™ line is designed to be easily maintained while providing a safe changing surface. These changing
stations are durable and built to deliver World Dryer® quality standards.
4" D / 17" 5.5" D / 34" 4" D / 17" .13" D / 18"
MODEL DESCRIPTIONS
ABC-300H:
Horizontal surface mounted with optional safety bracket available for mounting on weaker surfaces.
ABC-300H
ABC-300V
Vertical Mounted
ABC-300HS/ ABC-300 HSR
Stainless Steel Exterior
ABC-300V:
Vertical surface mounting provides added space savings. Changer tray made of Urethane
foam-filled for added strength and rigidity.
ABC-300HS:
Horizontal surface mounted with optional recessed mounting kit and a sleek stainless steel exterior.
ABC-300HSR:
Horizontal recessed mounted with sleek stainless steel exterior.
ACCESSORIES
May be ordered separately from changing stations.
ABC-300L:
Sanitary Bed Liners. Available in quantities of 500
ABC-300MB:
1 Steel Mounting Reinforcements Bracket. Available for ABC-300H and ABC-300HC Mode
BABY CHANGING STATIONS
ls
Mounting heights are measured from the floor to the bottom of the unit.
MOUNTING HEIGHTS
Mounting
Heights
10
www.worlddryer.com
800-323-0701 708-449-6950 fax: 708-449-6958
5700 McDermott Drive
Berkeley, IL 60163
www.worlddryer.com
WD0029_09/09
Loading...