Wolf Multi-Function Cooktop User Manual

MULTI-FUNCTION COOKTOP

INSTAL LATI ON INSTRU CT IO NS

INS T RU CCI ONES DE IN STALACI ÓN

INS T RU CTI ONS D’ INS TALLATI ON

IST RUZ ION I PER L’I NSTAL LAZ I ONE

INS TA LLATI O NSA NWE I SUN GEN

E N G L I S H 4

S P Ã N O L 1 6

F R A N Ç A I S 2 8

I T A L I A N O 4 0

D E U T S C H 5 2

C O N T A C T I N F O R M AT I O N

Website: wolfappliance.com

As you follow these instructions, you will notice WARNING and CAUTION symbols. This blocked information is important for the safe and efficient installation of Wolf equipment. There are two types of potential hazards that may occur during installation.

WOLF®is a registered trademark of Wolf Appliance, Inc.

signals a situation where minor injury or product damage may occur if you do not follow instructions.

states a hazard that may cause serious injury or death if precautions are not followed.

Another footnote we would like to identify is IMPORTANT NOTE: This highlights information that is especially relevant to a problemfree installation.

W O L F MULTI-FUNCTION COOKTO P

INSTALLATION R E Q U I R E M E N T S

IMPORTANT NOTE:

completed by a qualified installer or Wolf authorized service center technician.

Installer:

Instructions prior to installation. Save these instructions for the local inspector’s reference, then leave them with the homeowner.

Homeowner:

instructions for future reference and be sure to read the entire Use & Care Information prior to use.

IMPORTANT NOTE:

installed in accordance with local codes. The correct voltage, frequency and amperage must be supplied to the appliance from a dedicated, grounded circuit which is protected by a properly sized circuit breaker or time delay fuse. The proper voltage, frequency, and amperage ratings are listed on the product rating plate.

Record the model and serial numbers before installing the cooktop. Both numbers are listed on the rating plate, located on the underside of the cooktop. Refer to the illustration below.

Please read the entire Installation

This installation must be

Please read and keep these

This appliance must be

If the information in this book is not followed exactly, a fire or explosion may result, causing property damage, personal injury or death.

IMPORTANT NOTE:

Installation and service must be performed by a qualified installer, service agency or the gas supplier.

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

A ventilation hood or downdraft system is recommended (but not required) for use with the Wolf gas multi-function cooktop.

R AT I N G P L AT E I N F O R M A T I O N

Model Number

ICBIM15/S

Serial Number

Location of rating

plate under cooktop

Rating plate location

WHAT TO DO IF YOU SMELL GAS:

Do not try to light any appliance.

Do not touch any electrical switch.

Do not use any phone in your building.

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

If you cannot reach your gas supplier, call the fire department.

W O L F MULTI-FUNCTION COOKTO P

BEFO RE YO U S T A R T

Proper installation is your responsibility. Have a qualified technician install this cooktop. You must also ensure that electrical installation is adequate and in compliance with all local codes and ordinances.

Please check the product rating plate or Use & Care Information for type of gas needed.

Proper gas supply connection must be available; refer to Gas Supply Requirements on page 10. Electrical ground is required; see Electrical Requirements on page 11.

Check the location where the cooktop will be installed. The location should be away from strong draft areas, such as windows, doors and strong heating vents or fans. Do not obstruct flow of combustion and ventilation air.

Make sure you have everything necessary for correct installation. It is the responsibility of the installer to comply with the installation clearances specified on the product rating plate. The rating plate can be found on the underside of the cooktop.

This cooktop is intended for indoor use.

INSTALLATION I N S T R U C T I O N S

SITE P R E P A R AT I O N

IMPORTANT NOTE:

Installation of the Wolf gas multi-function cooktop must meet the following location requirements. All dimensions listed are minimum requirements for safe operation. Refer to the illustration below.

To eliminate the risk of burns or fire by reaching over heated surface units,

abinet storage space located above the

c surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a ventilation hood that projects horizontally a minimum of 127 mm beyond the bottom cabinets.

L O C A T I O N I N C O U N T E R T O P

Minimum flat countertop surface. Must be equal to or greater than the width of the module(s).

Minimum 178 mm wide clearance from the module side edge to any combustible surface up to 457 mm above the countertop (noted by shaded area).

O V E R H E A D C A B I N E T D I M E N S I O N S

Minimum spacing between overhead side cabinets must be greater than or equal to the nominal width of the module(s).

Minimum 457 mm vertical distance from

he countertop to the bottom of side

t cabinets within minimum side clearance.

Minimum vertical distance between the countertop and combustible materials above the cooktop module must be 762 mm.

Minimum 64 mm from rear wall.

Maximum 330 mm depth of overhead and side cabinets directly above and within side clearance.

Failure to locate the cooktop module without the proper clearances will result in a fire hazard.

Minimum installation clearances

W O L F MULTI-FUNCTION COOKTO P

127 mm

381 mm

LOCATION OF GAS SUPPLY

MAY ALSO EXTEND 127 mm ON

FLOOR FROM BACK WALL

178 mm*min

CUT-OUT TO

COMBUSTIBLE

MATERIALS

(BOTH SIDES)

356 mm

COOKTOP CUT-OUT

WIDTH

356 mm

COOKTOP CUT-OUT

WIDTH

838 mm

RECOMMENDED

CABINET WIDTH

457 mm

NOTE:Application shown allows for installation of two 381 mm modules side-by-side with 838 mm recommended cabinet width. 457 mm recommended cabinet width for installation of single 381 mm cooktop or module. *Minimum clearance from both side edges of cooktop cut-out to combustible materials up to 457 mm above countertop. **Minimum clearance from rear edge of cooktop cut-out to combustible materials up to 457 mm above countertop.

489 mm

COOKTOP CUT-OUT

DEPTH

64 mm

min

914 mm

STANDARD

FLOOR TO

COUNTERTOP

HEIGHT

330 mm

max

762 mm

COUNTERTOP TO

COMBUSTIBLE

MATERIALS

ABOVE COOKTOP

64**

127 mm

LOCATION OF GAS

SUPPLY MAY ALSO EXTEND

127 mm ON FLOOR FROM BACK WALL

FRONT OF COUNTERTOP

64 mm

min

489 mm

COOKTOP

CUT-OUT DEPTH

381 mm

OVERALL WIDTH

533 mm

OVERALL

DEPTH

127 mm

INSTALLATION S P E C I F I C A T I O N S

Model ICBIM15/S

The illustrations below provide the overall dimensions, installation specifications and countertop cut-out for Model ICBIM15/S.

If the cooktop is not installed above an oven, the gas service may be supplied through the floor. When an oven is installed below the cooktop, unless you are using cabinets deeper than 610 mm, it is recommended that the electrical supply be placed in the base cabinet to the right of the oven. Refer to the Installation Specifications illustration below for specifics on placement of the electrical and gas supply.

IMPORTANT NOTE:

When multiple cooktops and/or modules are installed side by side, refer to the countertop cut-out dimensions on page 9.

M O D E L I C B I M 1 5 / S D I M E N S I O N S

Overall Width 381 mm

Overall Height 127 mm

Overall Depth 533 mm

Minimum Cabinet Depth 578 mm

Minimum Height Clearance* 127 mm

Cut-Out Width 356 mm

Cut-Out Depth 489 mm

*A minimum height clearance of 140 mm is required between countertop and any combustible surface directly below the cooktop.

Unit dimensions may vary to±3 mm.

Overall Dimensions

Installation Specifications and Countertop Cut-Out Dimensions

INSTALLATION I N S T R U C T I O N S

64 mm

min

FRONT OF COUNTERTOP

489 mm

CUT-OUT

DEPTH

743 mm

TWO MODULES WIDTH

1130 mm – THREE MODULES WIDTH OR

1124 mm – 762 mm COOKTOP AND ONE MODULE

1518 mm – FOUR MODULES WIDTH OR

1511 mm – 762 mm COOKTOP AND TWO MODULES OR

1276 mm – 914 mm COOKTOP AND ONE MODULE

356 mm

CUT-OUT

WIDTH

INSTALLATION O P T I O N S

M U LT I P L E C O O K T O P I N S TA L L AT I O N

If the multi-function cooktop is to be used with any combination of additional cooktop units or modules with a filler strip, the cut-out width is calculated by adding the corresponding units' cut-out dimensions plus 32 mm for each additional unit. Refer to the illustration below.

IMPORTANT NOTE:

When multiple cooktops and/or modules are installed side by side, each unit must have its own separate recommended electrical circuit. When multiple gas cooktops and/or modules are installed next to one another, they can receive their gas supply from a common line.

When two or more modules are installed together, an integrated module filler strip (IFILLER/S) is recommended. Contact your Wolf dealer for information on these accessory components.

IMPORTANT NOTE:

Review specific installation instructions for product to product capabilities.

A C C E S S O R I E S

Optional accessories are available through your Wolf dealer.

Countertop cut-out dimensions for installation of multiple cooktops and/or modules

I M P O RTA N T N O T E

This installation must conform with local codes and ordinances.

W O L F MULTI-FUNCTION COOKTO P

GAS SUPPLY R E Q U I R E M E N T S

EXPLOSION HAZARD—

Securely tighten all gas connections.

Failure to do so can result in explosion, fire or death.

The product rating plate, located on the underside of the cooktop, has information on the type of gas that should be used. If this information does not agree with the type of gas available, contact your Wolf dealer. To obtain local dealer information, visit the Locator section of our website, wolfappliance.com.

An ISO 7-1 gas inlet thread is provided on all units. Please contact your local Wolf dealer if an ISO 228-1 or other gas inlet thread is required. Pipe joint compounds suitable for use with LP gas should be used. LP gas suppliers usually determine the size and materials used on the system.

If rigid pipe is used as a gas supply line, a combination of pipe fittings must be used to obtain an in-line connection to the cooktop. All strains must be removed from the supply and gas lines so the cooktop will be level and in line.

GAS R A T I N G

Total Heat Electrical Types and

Output Gas Rating Gas Pressures

Model # (Gas) Units (Amps) Category (mbar) Country of Destination

AT, DK, EE, FI, GR, IE, IT,

I2H G20 at 20 LT, NO, PT, ES, SE, SI, SK,

ICBIM15/S 8.0 kW 0.17

I2E G20 at 20 DE & PL

I2E+ G20 at 20/25 BE & FR

ICBIM15/S-LP 581 g/h 0.17 I3P G31 at 37

GB & CH

BE, CZ, FR, GR, IE, NL, NO, PT, ES, GB & CH

INSTALLATION I N S T R U C T I O N S

ELECTRICAL R E Q U I R E M E N T S

ELECTRICAL SHOCK HAZARD—

Plug into a grounded 3-prong electrical outlet.

Do not remove ground prong.

Do not use an adapter.

Failure to follow these instructions can result in electric shock, fire or death.

IMPORTANT NOTE:

If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.

Electronic ignition systems operate within wide voltage limits, but proper ground and polarity are necessary. In addition to checking that the electrical outlet provides 220-240 V AC power and is correctly grounded, the outlet must be checked by a qualified electrician to see if it is wired with correct polarity.

A wiring diagram covering the control circuit for the Wolf multi-function cooktop model can be found on page 15.

If an electrical outlet is not available, it is the obligation of the customer to have a properly grounded, 3-prong electrical outlet installed by a qualified electrician.

IMPORTANT NOTE:

Check with a qualified electrician if you are not sure whether the cooktop is properly grounded.

IMPORTANT NOTE:

Do not ground to a gas pipe.

A 220-240 V AC, 50/60 Hz, 15 amp electrical supply is required. A time-delay fuse or circuit breaker is recommended. It is recommended that a separate circuit serving only this appliance be provided.

IMPORTANT NOTE:

A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation.

W O L F MULTI-FUNCTION COOKTO P

Cooktop

Burner Box

Foam

Strip

Burner Box

89 mm

Clamping

Screw

Countertop

Bracket

Clip

C O O K T O P INSTALLATIO N

Insert the cooktop into the countertop cut-out opening. Center the cooktop in the opening and make sure that the front edge of cooktop is parallel to the front edge of the countertop. Check that all required clearances are met. Use a pencil to outline the rear edge of the cooktop on the countertop. Remove the cooktop from the countertop opening.

IMPORTANT NOTE:

When repositioning the cooktop in the countertop cut-out opening, lift the entire cooktop up from the opening to prevent scratching the countertop.

Remove the foam strip from the hardware package. Apply the foam strip around the bottom of the burner box flush with the edge as shown in the illustration below.

Reinsert the cooktop into the countertop opening. Check that the cooktop is parallel to the front edge of the countertop. Lift the entire cooktop to make adjustments and align the rear edge with the pencil line.

Attach the brackets to the burner box by inserting the clips into the rectangular punchouts on the left and right side of the burner box. Insert the 89 mm clamping screws into the brackets. Use a screwdriver to tighten the clamping screws against the underside of the countertop. Refer to the illustration below. Do not overtighten screws.

G A S S U P P LY L I N E C O N N E C T I O N

Assemble the flexible metal connector from the gas supply pipe to the gas entrance nipple. You will need to determine the fittings required, depending on the size of your gas supply line and flexible metal connector.

Use a pipe-joint compound made for use with natural and LP gas. If a flexible metal connector is used, be sure the tubing is not kinked.

Foam strip application

Bracket installation

INSTALLATION I N S T R U C T I O N S

C O O K T O P INSTALLATIO N

G A S L E A K T E S T I N G

Use a brush and liquid detergent to test all gas connections for leaks. Bubbles around connections will indicate a leak. If a leak appears, shut off gas valve controls and adjust connections. Then check connections again. Clean all the detergent solution from the cooktop.

Never test for a gas leak with a match or other flame.

C O M P L E T I N G T H E I N S TA L L A T I O N

Once the cooktop has been checked for any gas leaks, plug the power supply cord into the grounded electrical outlet.

Place the burner head on the burner base and position the burner grate over the burner assembly.

IMPORTANT NOTE:

Do not seal the cooktop to the countertop. It must be removed if service is necessary.

SURFACE B U R N E R S

I N I T I A L L I G H T I N G

The cooktop burner uses an electronic igniter in place of a standing pilot. When the cooktop control knob is pushed in and turned to the

position, the system creates a spark to light the burner. This sparking continues for 4 seconds or until the electronic ignition senses a flame, which ever comes first. If the igniter fails to ignite the gas in 4 seconds, the gas safety shutoff valve will close, eliminating the gas flow for 5 seconds. The valve will reopen after the purge time of 5 seconds, and the igniter will automatically attempt to re-ignite the gas. This cycle of events is attempted 3 times. After the third attempt, in order for gas to flow to the burner once again, the user must return the knob to the position and then turn the knob to the position.

To check operation of the cooktop burner, push in and turn the control knob to the position. The flame should light within four seconds.

If the burner does not light properly, turn the control knob to the position. Check that the burner head is in the proper position. Check that the power supply cord is plugged in and that the circuit breaker or house fuse has not blown. Check operation again; if the burner does not light properly at this point, contact your Wolf dealer or regional distributor.

IMPORTANT NOTE:

Initial lighting of the cooktop burner may take slightly longer as air in the system must be purged before gas can be supplied to the burner.

W O L F MULTI-FUNCTION COOKTO P

C O N T A C T I N F O R M AT I O N

Website: wolfappliance.com

COOKTO P R E M O V A L

If it is necessary to remove the multi-function cooktop for cleaning or service, shut off the gas supply. Disconnect the gas and electric supply. Remove the mounting brackets on the right and left side of the burner box and remove the cooktop. Reinstall in the reverse order and check the gas connection for leaks.

TROUBLES H O O T I N G

IMPORTANT NOTE:

If the multi-function cooktop does not operate properly, follow these troubleshooting steps:

Verify that power is being supplied to the cooktop.

Check the gas supply and electrical connections to ensure that the installation has been completed correctly.

Refer to the Troubleshooting Guide in the Wolf Multi-Function Cooktop Use & Care Information.

I F YO U N E E D SERVIC E

For service in your area, contact either your Wolf dealer or visit the Locator section of our website, wolfappliance.com to find the regional distributor by country.

When calling for service, you will need the model and serial number of your multifunction cooktop. Both numbers are listed on the rating plate, located on the underside of the cooktop. Refer to the illustration on page 5.

IMPORTANT NOTE:

Installation and service must be performed by a qualified installer or service agency.

If the cooktop still does not work, contact your Wolf dealer or regional distributor. Do not attempt to repair the cooktop yourself.

INSTALLATION I N S T R U C T I O N S

LACK

WHITE

BLACK

HITE

GAS VALVE

WHITE

BLACK

OWER CORD

RN/YEL

GRN/YEL

DSI

RED

10 7

WIRING D I A G R A M

Model ICBIM15/S

The information and images in this book are the copyright property of Wolf Appliance, Inc., an affiliate of Sub-Zero, Inc. Neither this book nor any information or images contained herein may be copied or used in whole or in part without the express written permission of Wolf Appliance, Inc., an affiliate of Sub-Zero, Inc.

I N F O R M A C I Ó N D E C O N TA C T O

ágina Web:

wolfappliance.com

Cuando consulte las instrucciones que aparecen en esta guía, encontrará símbolos de ADVERTENCIA y PRECAUCIÓN. Esta información en recuadros es importante para instalar el equipo de Wolf de forma segura y eficaz. Existen dos tipos de posibles riesgos que pueden producirse durante una instalación.

WOLF®es una marca comercial registrada de Wolf Appliance, Inc.

indica una situación en la que se pueden sufrir heridas leves o provocar daños secundarios al producto si no se siguen las instrucciones.

indica peligro de que se produzcan heridas personales graves o incluso puede provocar la muerte si no se siguen las precauciones especificadas.

Otro tipo de anotación que es importante resaltar es la que se incluye en NOTA IMPORTANTE: En esta nota se resalta la información que resulta especialmente importante para que la instalación se realice sin problemas.

PLACA MULTIFUNC IÓ N D E W O L F

R E Q U I S I T O S D E INSTALAC IÓ N

NOTA IMPORTANTE:

realizada por un técnico cualificado o por un técnico de mantenimiento autorizado de Wolf.

Instalador:

lación antes de llevar a cabo la instalación. Guarde estas instrucciones para que el inspector local pueda utilizarlas como referencia y, a continuación, entréguelas al propietario del aparato.

Propietario:

para que pueda utilizarlas como referencia en el futuro y asegúrese de leer la guía de uso y mantenimiento antes de utilizar el aparato.

NOTA IMPORTANTE:

larse siguiendo las normativas nacionales correspondientes. Se debe aplicar al aparato el voltaje, la frecuencia y el amperaje adecuados desde una instalación eléctrica resistente con toma de tierra protegida por un fusible de retardo. El voltaje, la frecuencia y el amperaje se muestran en la placa de datos del producto.

Apunte la referencia del modelo y el número de serie antes de instalar el aparato. Esta información se muestra en la placa de datos del producto situada en la parte inferior de la placa. Observe la siguiente ilustración.

Lea las instrucciones de insta-

Esta instalación debe ser

Lea y guarde estas instrucciones

Este aparato debe insta-

Si no sigue exactamente las instrucciones que se proporcionan en esta guía, es posible que se produzca un incendio o una explosión lo cual puede provocar daños en la propiedad, heridas graves o incluso la muerte.

NOTA IMPORTANTE:

La instalación y el mantenimiento deben ser realizados por un instalador cualificado, por un centro de asistencia técnica o por el proveedor de gas.

No almacene ni utilice gasolina ni otros vapores ni líquidos inflamables cerca de éste o de otros aparatos.

Se recomienda utilizar una campana extractora o un ventilador de tiro ascendente con la placa de gas multifunción de Wolf, aunque no es obligatorio.

I N F O R M A C I Ó N D E L A P L A C A D E D A T O S

eferencia del

odelo

ICBIM15/S

úmero de serie

Ubicación de la placa de datos debajo de la

vitrocerámica

Ubicación de la placa de datos

QUÉ SE DEBE HACER SI HUELE A GAS:

No encienda ningún aparato.

No toque ningún interruptor eléctrico.

No utilice ningún teléfono dentro del edificio.

Llame inmediatamente a su proveedor de gas desde el teléfono de un vecino. Siga las instrucciones que le proporcione el proveedor de gas.

Si no le es posible ponerse en contacto con el proveedor de gas, llame a los bomberos.

PLACA MULTIFUNC IÓ N D E W O L F

ANTES D E C O M E N Z A R

Es responsabilidad del propietario asegurarse de que la instalación se realiza de manera correcta. Esta placa debe ser instalada por un técnico cualificado. Debe comprobar que la instalación eléctrica es la correcta y que cumple todos los códigos y normativas nacionales.

Revise la placa de datos del producto o lea la guía de uso y mantenimiento para obtener información sobre el tipo de gas que necesita.

Debe disponer de una entrada de suministro de gas; consulte la sección Requisitos del suministro de gas en la página 22. También debe disponer de una conexión eléctrica a tierra; consulte la sección Requisitos eléctricos en la página 23.

Inspeccione el lugar en el que va a instalar la placa. El lugar en el que va a instalarla debe estar alejado de áreas en las que pueda haber corrientes fuertes, por ejemplo, ventanas, puertas y salidas de aire caliente o ventiladores. No debe obstruir el flujo de combustión ni el aire de ventilación.

Compruebe que tiene todo lo necesario para que la instalación se lleve a cabo de la manera correcta. Es responsabilidad del instalador dejar los espacios requeridos para la instalación que se especifican en la placa de datos del producto. La placa de datos está ubicada en la parte inferior del aparato.

Esta placa está diseñada para que se utilice en espacios interiores.

I N S T R U C C I O N E S D E INSTALACIÓ N

P R E PA R A C I Ó N D E L SITIO

NOTA IMPORTANTE:

La instalación de la placa multifunción de gas de Wolf debe cumplir los siguientes requisitos de colocación. Las medidas que se especifican son las mínimas para que el funcionamiento de la placa sea seguro. Observe la siguiente ilustración.

Para eliminar el riesgo de sufrir quemaduras o de que se produzca un incendio al alcanzar las superficies calientes, debe evitar colocar armarios por encima de los módulos de superficie. Si va a colocar armarios, el riesgo se puede reducir instalando una campana de extracción que sobresalga horizontalmente un mínimo de 127 mm de la parte inferior de los armarios.

C O L O C A C I Ó N E N L A E N C I M E R A

Superficie mínima de encimera plana. Debe ser igual o superior al ancho del módulo o módulos.

Espacio mínimo de 178 mm desde el borde lateral del módulo a cualquier superficie combustible situada 457 mm por encima de la encimera (área sombreada de la ilustración).

M E D I D A S D E L O S A R M A R I O S S U P E R I O R E S

El espacio mínimo entre los armarios laterales superiores debe ser igual o superior al ancho nominal del módulo o módulos.

Debe existir una distancia vertical mínima de 457 mm desde la encimera hasta la parte inferior de los armarios laterales con una distancia lateral mínima.

La distancia vertical mínima entre la encimera y los materiales combustibles situados por encima de la placa debe ser de 762 mm.

Distancia mínima de 64 mm a la pared trasera.

El fondo máximo de los armarios superiores laterales situados por encima de la placa debe ser de 330 mm con una distancia lateral mínima.

Si no coloca el módulo de la placa siguiendo las distancias de separación correctas, es posible que se produzca un incendio.

Distancias mínimas de instalación

PLACA MULTIFUNC IÓ N D E W O L F

127 mm

381 mm

LA UBICACIÓN DE LA TOMA DE GAS

SE PUEDE EXTENDER 127 mm EN EL

SUELO DESDE LA PARED TRASERA

178 mm*

mín

DESDE CORTE

A LOS

MATERIALES

INFLAMABLES

(AMBOS LADOS)

356 mm

ANCHURA DE CORTE

DE LA SUPERFICIE

DE COCCIÓN

356 mm ANCHURA DE CORTE DE LA

SUPERFICIE DE COCCIÓN

838 mm

ANCHURA DELARMARIO R

ECOMENDADO

457 mm

NOTA:La aplicación que se muestra permite la instalación de dos módulos contiguos de 381 mm con un armario con una anchura recomendada de 838 mm. 457 mm de anchura de armario recomendada para la instalación de un solo módulo o superficie de cocción de 381 mm. *Espacio mínimo desde ambos bordes laterales del corte de la superficie de cocción hasta la superficie inflamable situada a 457 mm por encima de la encimera. **Espacio mínimo desde el borde trasero del corte de la superficie de cocción a la superficie inflamable situada a 457 mm sobre la encimera.

489 mm

PROFUNDIDAD DE

CORTE DE LA

SUPERFICIE DE COCCIÓN

64 mm

mín

914 mm

ALTURA

ESTÁNDAR DEL SUELO A LA ENCIMERA

330 mm

máx

762 mm ENCIMERA A MATERIALES

COMBUSTIBLES

SOBRE

LA SUPERFICIE

DE COCCIÓN

64**

127 mm

LA UBICACIÓN DE LA TOMA

DE GAS SE PUEDE EXTENDER

127 mm EN EL SUELO DESDE

LA PARED TRASERA

PARTE DELANTERA DE LA ENCIMERA

64 mm

mín

489 mm

PROFUNDIDAD

DE CORTE

DE LA SUPERFICIE

DE COCCIÓN

381 mm

ANCHURA TOTAL

33 mm

PROFUNDIDAD

TOTAL

127 mm

E S P E C I F I C A C I O N E S D E L A

INSTALAC IÓ N

odelo ICBIM15/S

Las ilustraciones que se muestran a continuación proporcionan las medidas totales, las especificaciones de instalación y el corte de la encimera que corresponden al modelo CBIM15/S.

Si no instala la placa sobre un horno, el suministro de gas puede realizarse a través del suelo. Cuando instale un horno debajo de una placa, se recomienda que el suministro eléctrico se coloque en el armario de la base situado a la derecha del horno, a menos que esté utilizando armarios con un fondo superior a 610 mm. Observe la ilustración Especificaciones de instalación que se muestra a continuación para obtener información específica sobre la ubicación del suministro eléctrico y de gas.

NOTA IMPORTANTE:

En el caso de que instale varias placas y/o módulos juntos, consulte las dimensiones del corte de la encimera en la página 21.

D I M E N S I O N E S D E L M O D E L O I C B I M 1 5 / S

Anchura total 381 mm

Altura total 127 mm

Profundidad total 533 mm

Fondo mínimo del armario 578 mm

Espacio de altura mínimo* 127 mm

Ancho del corte 356 mm

Profundidad del corte 489 mm

*Se necesita dejar un espacio mínimo de altura

e 140 mm entre la placa y cualquier superficie

d combustible que se encuentre justo debajo de la placa.

Las medidas de la unidad pueden variar±3 mm.

Especificaciones de la instalación Medidas de corte de la encimera

Medidas totales

+ 44 hidden pages