Page 1
I NSTALLATION I NSTRUCTIONS
P RO I SLAND V ENTILATION H OODS
Page 2
As you follow these instructions, you will
notice WARNING and CAUTION symbols.
This blocked information is important for the
safe and efficient installation of Wolf equipment. There are two types of potential
hazards that may occur during installation.
Another footnote we would like to identify is
IMPORTANT NOTE: This highlights information that is especially relevant to a problemfree installation.
signals a situation where minor injury or
product damage may occur if you do not
follow instructions.
states a hazard that may cause serious
injury or death if precautions are not
followed.
WOLF®is a registered trademark of Wolf Appliance Company, LLC
CONTACT
INFORMATION
Wolf Customer
Service:
800-332-9513
Website:
wolfappliance.com
Page 3
3
INSTALLATION REQUIREMENTS
IMPORTANT NOTE:
This installation must be
completed by a qualified installer or Wolf
authorized service center technician.
Installer:
Please read the entire Installation
Instructions prior to installation. Save these
instructions for the local inspector’s reference, then leave them with the homeowner.
Homeowner:
Please read and keep these
instructions for future reference and be sure
to read the entire Use & Care Information
prior to use.
Any questions or problems about the
installation should be directed to your Wolf
dealer or Wolf Appliance Company, LLC at
800-332-9513. You can also visit our website
at wolfappliance.com.
IMPORTANT NOTE:
This appliance must be
installed in accordance with National Electrical
Codes, as well as all state, municipal and local
codes. The correct voltage, frequency and
amperage must be supplied to the appliance
from a dedicated, grounded circuit which is
protected by a properly sized circuit breaker or
time delay fuse. The proper voltage, frequency,
and amperage ratings are listed on the product
rating plate.
Record the model and serial numbers before
installing the Pro island ventilation hood. Both
numbers are listed on the rating plate, located
on the left wall of the hood shell.
WOLF PRO ISLAND VENTILATION HOODS
Island Hood
Island Hood
(R) Rail Option
Dimensions in parentheses are in
millimeters unless otherwise specified.
LIST OF MATERIALS
The following is a list of materials shipped
with the Wolf Pro island ventilation hood.
Stainless steel island hood
Transition with backdraft damper (attached
inside hood—needs to be removed)
Decorative stainless steel rails and installation components—(R) model hoods only
Two control knobs
Filters and grease cups (installed in hood)
(8–16) #10 x 2" (51) self-tapping hex head
screws (number of screws varies with the
width of the island hood)
(4)
1
/4" x 3" (76) lag screws
Installation package (taped to filters)
Installation Instructions
Use & Care Information and product
registration card
Wolf logo nameplate
Rating plate location
Location of rating plate
inside left wall
Model Number
Serial Number
Page 4
4
WOLF PRO ISLAND VENTILATION HOODS
IMPORTANT NOTE:
Wolf recommends that
the Pro island ventilation hood be installed
30" (762) to 36" (914) above the countertop.
Rail option (R) island hoods come with classic
stainless steel decorative rails and stand-offs
on both sides of the hood. Optional platinum
or brass rails are available to match Wolf dual
fuel range bezels. Contact your Wolf dealer for
details.
ELECTRICAL REQUIREMENTS
Wolf Pro island ventilation hoods require a
separate, grounded 110/120 V AC, 60 Hz power
supply. The service should have its own 15
amp circuit breaker. Locate the electrical
supply through the top of the hood. Refer to
the Installation Specifications illustration on
the following page.
You must follow all National Electrical Code
regulations. In addition, be aware of local
codes and ordinances when installing your
service.
DUCT COVER
If you are installing a Wolf duct cover with the
Pro island hood, refer to instructions on page 8
before installing the hood.
ACCESSORIES
Optional accessories are available
through your
Wolf dealer. To
obtain local dealer
information, visit
the Locator section
of our website,
wolfappliance.com.
INSTALLATION CONSIDERATIONS
IMPORTANT NOTE:
Wolf Pro island ventilation hoods are recommended for use with all
Wolf cooking appliances.
Proper installation is the responsibility
of the installer. Product failure due to
improper installation is not covered
under the Wolf Warranty. Refer to the Wolf
Pro Ventilation Hoods Use & Care
Information for warranty details, or visit
the Contact/ Help section of our website,
wolfappliance.com.
Make sure you have the tools and materials
necessary for proper installation.
Warranty service must be performed by a
Wolf authorized service center. Wolf is not
responsible for service required to correct a
faulty installation.
IMPORTANT NOTE:
Wolf Pro ventilation
hoods are shipped without the blower
assembly. Wolf internal, in-line and remote
blower assemblies are available; refer to pages
13–15. Use only a Wolf blower with the Pro
island hood.
Page 5
5
Dimensions in parentheses are in
millimeters unless otherwise specified.
INSTALLATION INSTRUCTIONS
TOP WIDTH
SUBTRACT 18" (457) FROM OVERALL WIDTH
18" (457)
OVERALL
HEIGHT
OVERALL WIDTH
34" (864)
OVERALL DEPTH
13"
(330)
4"(102)
2"
(51)
3
/4" (19)
DIAMETER
OF RAIL
2"
(51)
OVERALL DIMENSIONS
PRO ISLAND HOODS
Overall Widths 36" (914), 42" (1067),
54" (1372) and 66" (1676)
Overall Height
18" (457)
Overall Depth (
excluding
rails) 34" (864)
Shipping Weight (shell only) 95–168 lbs
(43–76 kg)
Dimensions may vary to ±1/8" (3).
Pro Island Hood
18" (457)
HEIGHT
OF HOOD
34" (864)
DEPTH OF HOOD
WIDTH OF HOOD
LOCATION OF ELECTRICAL SUPPLY
CENTERED THROUGH TOP OF HOOD
30" TO 36"
(762–914)
TO COUNTERTOP
30" TO 36"
(762–914)
TO COUNTERTOP
INSTALLATION SPECIFICATIONS
Pro Island Hood
Page 6
6
WOLF PRO ISLAND VENTILATION HOODS
INSTALLATION SPECIFICATIONS
The illustration and chart below provides
dimensions critical for proper installation of
the Wolf Pro island ventilation hood.
34" (864)
DEPTH OF
HOOD
A
WIDTH OF
HOOD
B
WIDTH OF
TOP PLATE
C
HEIGHT OF
TRANSITION
D
TO CENTER
OF TRANSITION
6
1
/2
"
(165)
13"
(330)
10" (254)
Pro Island Hoods
Model (A) (B) (C) (D)
I363418 36" (914) 18" (457) 83/4" (222) 9" (228)
I423418 42" (1066) 24" (610) 83/4" (222) 12" (304)
I543418 54" (1371) 36" (914) 83/4" (222) 18" (457)
I663418 66" (1676) 48" (1219) 83/4" (222) 24" (610)
Letters correspond to those in the illustration.
To reduce the risk of fire and electric
shock, install this ventilation hood only
with a blower manufactured by Wolf.
Blower model numbers are listed on
page 17.
Page 7
7
Dimensions in parentheses are in
millimeters unless otherwise specified.
INSTALLATION INSTRUCTIONS
INSTALL DUCTWORK
IMPORTANT NOTE:
Wolf recommends that
the Pro island ventilation hood be installed
30" (762) to 36" (914) above the countertop.
IMPORTANT NOTE:
Consult a qualified HVAC
Engineer for specific ducting applications.
IMPORTANT NOTE:
All Wolf Pro ventilation
hoods must exhaust to the outdoors. Always
use metal ducting. Do not use flex ducting.
Decide where the ductwork will run between
the hood and the outside. A straight, short
duct run will allow the hood to perform more
efficiently. Limit the number of elbows and
transitions to as few as possible. Long duct
runs, elbows and transitions will reduce the
performance of the hood. Wolf recommends
the maximum linear duct run be no greater
than 50' (15 m). The Pro island hood has a
vertical discharge.
IMPORTANT NOTE:
There is a possibility of
noise issues, if there is a short duct run
coupled with a remote blower.
Always install a roof or wall cap if you are not
installing a remote blower. Connect 10" (254)
round metal ductwork to the cap and work
back towards the hood. Use duct sealing tape
on joints between ductwork sections.
Wolf Pro island hoods come standard with a
backdraft damper included in the transition
assembly. Local codes may require the use of
an additional backdraft damper. Contact your
local HVAC professional for specific requirements. In cold weather installations a backdraft
damper is necessary to minimize the backflow
of cold air into the room.
Local building codes may require the use of
make-up air. Consult your local HVAC professional for specific requirements in your area.
To reduce the risk of fire, use only metal
ductwork.
ROOF CAP OR REMOTE BLOWER
18" (457)
HEIGHT OF HOOD
ISLAND HOOD
DUCTWORK INSTALLATION
THROUGH ROOF
34" (864)
DEPTH OF HOOD
10" ROUND DUCT
VERTICAL
DISCHARGE
VERTICAL DISCHARGE ONLY FOR ISLAND HOODS.
TRANSITION
14
1
/8"W x 9"D TO 10" ROUND
11"H (INCLUDING FLANGES)
SOFFIT, CABINET OR
DUCT COVER
30" TO 36"
(762–914)
COUNTERTOP
TO BOTTOM OF
VENTILATION HOOD
36" (914)
STANDARD
FLOOR TO
COUNTERTOP
HEIGHT
Ducting options for island hoods
Page 8
8
WOLF PRO ISLAND VENTILATION HOODS
DUCT COVER INSTALLATION
IMPORTANT NOTE:
If an optional duct cover
is to be used, it must be installed before
installing the island hood.
Duct covers 6" (152) and 12" (305) high in
widths to match all island hoods are available
through your Wolf dealer. To obtain local
dealer information, visit the Locator section of
our website, wolfappliance.com.
Duct cover installation
Installing a duct cover assembly will
impact all aspects of the hood installation including hood location, ducting,
electrical placement and the mounting
surface.
ACCESSORIES
Optional accessories are available
through your
Wolf dealer. To
obtain local dealer
information, visit
the Locator section
of our website,
wolfappliance.com.
The duct cover must be attached to the ceiling
before installing the hood. Refer to the illustration below and install the duct cover using the
following steps.
Use four
1
/4" x 3" (76) lag screws (included
with the hood) to attach the duct cover to
ceiling framing. Refer to the chart on page 6
for the specific dimensions of your model.
Install additional #10 x 2" (51) hex head
screws (included with the hood) along the
top edge of the duct cover for support.
Install four
5
/16" stainless steel bolts
(included with the duct cover) through the
mounting holes on each corner of the hood
and into the bottom edge of the duct cover.
Attach the duct cover to the hood assembly
with #12 x
7
/8" (22) self-tapping hex head
screws (included with the duct cover).
Duct
Cover
5
" Nut
/16
5
" Bolt
/16
7
" (22)
#12 x
/8
Self-Tapping
Hex Head Screw
(51)
#10 x 2"
Hex Head Screw
1
" x 3" (76)
/4
Lag
Screw
Page 9
9
Dimensions in parentheses are in
millimeters unless otherwise specified.
INSTALLATION INSTRUCTIONS
HOOD PREPARATION
Follow these steps to prepare the island hood
for installation:
Slide the grease cups out from the bottom
edges of the front and back of the hood.
Remove the filters by pressing up at the
angle the filters are placed in, then rotate
the bottom of the filter down. Gloves
should be worn to provide a proper grip.
Remove the center filter bank by removing
two screws from each end of the hood.
Do
not discard the screws
, they will be reinstalled after installation of the hood is
complete. Refer to the illustration below.
The hood assembly is shipped with the
transition attached. The transition is
shipped upside down in the top of the hood
and must be removed and reinstalled in the
proper position.
Separate the transition from the hood
assembly by removing the four shipping
screws. Invert and reattach the transition to
the hood with the shipping screws.
Remove filters and center filter bank
If you are installing a remote blower, drill a
7
/8" (22) hole through the hood framing for
the conduit. Refer to the remote blower
information on page 14 and follow installation instructions provided with the blower.
IMPORTANT NOTE:
Do not run wiring for the
remote blower through the ductwork.
Center Filter Bank
Location of
Screws for
Center Filter Bank
Filter
Page 10
10
WOLF PRO ISLAND VENTILATION HOODS
ACCESSORIES
Optional accessories are available
through your
Wolf dealer. To
obtain local dealer
information, visit
the Locator section
of our website,
wolfappliance.com.
INSTALL THE ISLAND HOOD
IMPORTANT NOTE:
If an optional duct cover
is to be used, it must be installed before
installing the island hood. Refer to Duct Cover
Installation on page 8.
IMPORTANT NOTE:
There must be a
minimum 10" (254) opening between ceiling
framing to accommodate the ductwork necessary for proper ventilation.
The filters and center filter bank must be
removed prior to installation of the island
hood. Refer to Hood Preparation on page 9.
Layout the dimensions of the hood top
mounting plate on the ceiling. The top plate
dimensions will vary with the size of the
hood. For the dimensions of your model,
refer to the illustration and chart on page 6.
Use minimum 2 x 4 lumber to construct the
framing. Proper structural support is
required to accommodate the weight of the
hood.
Framing must be tied together and to
ceiling joists to provide enough structural
strength to support the weight of the
hood and internal blower, if applicable.
Mark the center location of the hood.
Install 2 x 4 blocking between ceiling joists.
Refer to the illustration below.
Drill
5
/32" (4) holes in the 2 x 4 framing to
match mounting holes in the top plate of
the hood.
Lift the hood and align the hood mounting
holes with the predrilled holes in the
framing. Install the
1
/4" x 3" (76) lag screws
(included with the hood) through the
mounting holes on each corner of the hood
and into the framing.
Do not overtighten
the screws.
Connect the 10" (254) round ductwork to the
transition using sheet metal screws and
duct sealing tape.
Make the electrical connections. Refer to
Install Wiring on page 12.
Island hood framing – top view
1
Island Hood
Top Plate
13"
(330)
(76)
10"
Ductwork
Existing
Ceiling Joists
Width of top plate varies with width of island hood
" x 3" (76)
/4
Lag Screws
2 x 4 Blocking
Page 11
11
Dimensions in parentheses are in
millimeters unless otherwise specified.
INSTALLATION INSTRUCTIONS
When making electrical connections,
make sure the electrical power is turned
off at the power source or circuit breaker
before proceeding.
Adjust the positioning of the hood if
necessary, and tighten all four lag screws
until the hood is flush with the ceiling.
Install the #10 x 2" (51) screws (included
with the hood) through the remaining
mounting holes in the top plate of the hood
for additional support. Refer to the illustration below.
If you are installing an internal blower, do
not reinstall the center filter bank and filters
until the blower installation is complete.
Refer to the internal blower information on
page 13 and follow installation instructions
provided with the blower.
Due to the weight of the island hood,
be sure to have adequate manpower for
installation.
1
/4
" x 3" (76)
Lag Screw
#10 x 2"
(51)
Hex Head Screw
Island Hood
Top Plate
Island hood installation
INSTALL THE ISLAND HOOD
Page 12
Run a 120 V AC, 15 amp circuit power cable
from the service panel to the electrical box
at the center of hood. Supply a minimum of
6' (1.8 m) of ROMEX cable.
Remove the knockout located on the left
side of the hood top plate. Refer to the
illustration and chart below for the wiring
location of your specific model.
Insert the conduit through the hole on top
of the hood to the electrical box located in
center of hood shell.
Remove the hood electrical box cover.
Connect black wire to power supply black
wire, white wire to power supply white wire
and green wire to green wire or bare wire.
Place all wiring connections inside the
electrical box and reinstall the cover. Make
sure that the wires are secure and that no
wires are pinched between the cover and
box.
Refer to the wiring diagram packaged with the
island hood for more information.
12
WOLF PRO ISLAND VENTILATION HOODS
INSTALL WIRING
This ventilation hood must be properly
grounded. This unit should be installed by
a qualified electrician in accordance with
all applicable national and local electrical
codes.
Before servicing or cleaning unit, switch
power off at service panel and lock the
service disconnecting means to prevent
power from being switched on accidentally. When the service disconnecting
means cannot be locked, securely fasten a
prominent warning device, such as a tag,
to the service panel.
Do not remove the control knob bezel to
access hood wiring, this will damage the
bezel assembly.
B
Transition Cut-Out
8"
(203) x 5
7
/8
" (149)
Location of
Knockout
A
Island hood wiring location
IMPORTANT
NOTE
You must follow
all National
Electrical Code
regulations. In
addition, be aware
of local codes and
ordinances when
installing your
service.
Location of Knockout for Wiring
Model (A) (B)
I363418 1" (25) 1" (25)
I423418 2" (51) 11/2" (38)
I543418 8" (203) 11/2" (38)
I663418 14" (356) 11/2" (38)
Letters correspond to the illustration.
Page 13
13
Dimensions in parentheses are in
millimeters unless otherwise specified.
INSTALLATION INSTRUCTIONS
INTERNAL BLOWER
IMPORTANT NOTE:
Refer to the installation
instructions provided with the internal
blower for additional mounting and wiring
instructions.
IMPORTANT NOTE:
Use wire connectors or
wire nuts approved by UL or C/UL.
IBLOWER-120INT INSTALLATION
Remove filters and center filter bank from
the island hood. Refer to Hood Preparation
on page 9.
Lift the blower into position inside the
hood.
Engage the two tabs on the blower into the
two slots in the top of the island hood.
Secure the blower to the threaded studs
with two hex nuts (included with the
blower). Refer to the illustration below.
Plug the blower power cords into receptacles located near the center of the hood
shell. Use the clips on the interior of the
hood to keep excess power cord away from
moving parts.
Once installation of the blower is complete,
replace the center filter bank and filters.
IMPORTANT NOTE:
Before turning the power
on to the ventilation hood, make sure the
blower is off.
Internal blower installation
Top of Hood
Slot
Ta b
Internal Blower
Hex Head Nuts
Threaded
Studs
Powe r
Cords
Page 14
14
WOLF PRO ISLAND VENTILATION HOODS
IN-LINE AND REMOTE BLOWERS
BLOWER INSTALLATION
IMPORTANT NOTE:
Refer to the specific
installation instructions provided with each
blower for additional mounting instructions.
Locate the blower so that the length of the
duct run and number of elbows and transitions
are kept to a minimum. Wolf recommends the
maximum linear duct run be no greater than
50' (15 m).
If possible, remote blowers should be located
between wall studs or roof rafters. Avoid
pipes, wires or other ductwork that may be
running through the wall.
Be sure that there is enough space for any
transitions that may be needed between the
blower and the connecting ductwork. For best
performance, locate transitions nearest the
blower.
Refer to the illustrations below and on the
following page for overall dimensions of Wolf
in-line and remote blowers. Also refer to the
specific installation instructions provided with
each remote blower to verify cut-out dimensions.
Dimensions for BLOWER-90REM
Dimensions for BLOWER-150REMDimensions for BLOWER-120REM
3
/4
20
"
28
(718)
1
"
/4
Diameter
1
15
"
/2
(394)
14"
(356)
10" (254)
3
/4
24
(629)
(527)
1
24
"
/2
(622)
3
4
"
/4
"
(121)
29
(749)
25"
(635)
21" (533)
10"
(254)
29
(749)
7
(184)
1
"
/2
1
"
/4
18" (457)
10"
1
"
/2
10" (254)
Diameter
3
14
"
/4
(375)
1
10
"
/8
(257)
22"
(559)
(254)
29
(749)
7
(184)
1
29
"
/2
(749)
1
/2
"
1
/4
"
14
(375)
10" (254)
Diameter
3
"
/4
3
10
"
/8
(264)
Page 15
18"
(457)
22"
(559)
24
7
/8
"
(632)
12"
(305)
18"
(457)
8"
(203)
15
Dimensions in parentheses are in
millimeters unless otherwise specified.
INSTALLATION INSTRUCTIONS
IN-LINE AND REMOTE BLOWERS
BLOWER WIRING
IMPORTANT NOTE:
Refer to the specific
installation instructions provided with each
blower for additional wiring instructions.
Follow wiring instructions at the blower as
outlined in the specific installation instructions provided with each blower. Black (L1)
to black, white (neutral) to white, or white
to blue, or white to brown (depending on
model) and green to grounding screw. Run
blower cable (ROMEX) to the hood.
Insert 30" (762) of ROMEX cable through
the knockout opening and into the electrical
box on the rough-in plate of the hood.
Secure the cable to the electrical box with
an appropriate connector.
Locate the cord assembly provided with the
blower. The cord assembly has two leads,
black (L1) and white (neutral). Connect
these leads to the leads from the blower,
black to black and white to white.
Connect
all
green and bare wires together
to the ground screw in the electrical box.
Plug the cord assembly into the receptacle
located near the center of the hood shell.
Use the clips on the interior of the hood to
keep excess power cord away from moving
parts.
Reinstall the electrical box cover and
screws. Make sure that all wires are secure
and that no wires are pinched between the
cover and box.
IMPORTANT NOTE:
Before turning the power
on to the ventilation hood, make sure the
blower is off.
When making electrical connections,
make sure the electrical power is turned
off at the power source or circuit breaker
before proceeding.
Dimensions for BLOWER-110IL
Page 16
16
WOLF PRO ISLAND VENTILATION HOODS
LOGO NAMEPLATE
The Wolf logo nameplate does not come
installed on the hood since there are various
locations that the nameplate can be attached.
Also, some customers prefer not to have a
nameplate on their hood.
A template for positioning the Wolf logo
nameplate in a standard location is included
on page 19. Follow these steps to install the
nameplate:
Decide on the location for the nameplate.
Clean the mounting area with rubbing
alcohol.
If desired, cut-out the template from page
19. Fold the template, locate placement on
hood and tape to the hood surface. Check
alignment and adjust if necessary.
Remove backing paper from the nameplate.
Position the nameplate in the template
cut-out and press into place.
Remove the template and any tape residue.
INSTALL FILTERS / GREASE CUPS
Reinstall the center filter bank. Leave the
screws slightly loosened until after the
filters are in place. Refer to Hood Preparation on page 9.
Remove all packaging material from the
filters and grease cups.
Slide the grease cups along the bottom
edge of the hood so that the lip of the
grease cup overhangs slightly.
Install the filters. Orient each filter with
lines running vertically. Position the top
edge of the filter as shown in the illustration below. While pressing up against the
spring, rotate the bottom edge of the filter
into position next to the grease cup. Gloves
should be worn to provide proper grip.
Filter and grease cup installation
Spring
Filter
Grease Cup SIDE VIEW
Page 17
17
Dimensions in parentheses are in
millimeters unless otherwise specified.
INSTALLATION INSTRUCTIONS
BLOWER ASSEMBLIES
Wolf Pro island ventilation hoods are shipped
without the blower assembly. Wolf internal,
in-line and remote blower assemblies are
available as sales accessories through your
Wolf dealer.
IMPORTANT NOTE:
Blower options vary with
the cooking surface. Use only a Wolf blower
with the Pro island ventilation hood.
INTERNAL BLOWER
IBLOWER-120INT (804703) –
1200 CFM
internal blower for all island hoods.
IN-LINE BLOWER
BLOWER-110IL (808190) –
1100 CFM
in-line blower for all island hoods.
REMOTE BLOWERS
BLOWER-90REM (801641) –
900 CFM
remote blower for Models I363418, I423418
and I543418.
BLOWER-120REM (801642) –
1200 CFM
remote blower for all island hoods.
BLOWER-150REM (804701) –
1500 CFM
remote blower for all island hoods.
Refer to the Wolf Design Guide for Pro ventilation recommendations. You can also visit our
website at wolfappliance.com.
ACCESSORIES
Optional accessories are available
through your
Wolf dealer. To
obtain local dealer
information, visit
the Locator section
of our website,
wolfappliance.com.
TROUBLESHOOTING
IMPORTANT NOTE:
If the Pro island ventilation hood does not operate properly, follow
these troubleshooting steps:
Verify that power is being supplied to the
ventilation hood.
Check electrical connections to ensure that
the installation has been completed
correctly.
Refer to the Troubleshooting Guide in the
Wolf Pro Ventilation Hoods Use & Care
Information.
If the ventilation hood still does not work,
contact a Wolf authorized service center. Do
not attempt to repair the ventilation hood
yourself. Wolf is not responsible for service
required to correct a faulty installation.
Page 18
18
CONTACT
INFORMATION
Wolf Customer
Service:
800-332-9513
Website:
wolfappliance.com
IF YOU NEED SERVICE
Maintain the quality built into your Pro
island ventilation hood by calling a Wolf
authorized service center.
For the name and number of the Wolf
authorized service center nearest you,
check the Locator section of our website,
wolfappliance.com
, or call Wolf Customer
Service at
800-332-9513
.
When calling for service, you will need the
model and serial number of your ventilation
hood. This information is found on the
rating plate located on the left wall of the
hood shell. Refer to the illustration on
page 3.
WOLF PRO ISLAND VENTILATION HOODS
The information and images are the copyright
property of Wolf Appliance Company, LLC, an
affiliate of Sub-Zero Freezer Company, Inc.
Neither this book nor any information or images
contained herein may be copied or used in whole
or in part without the express written permission
of Wolf Appliance Company, LLC, an affiliate of
Sub-Zero Freezer Company, Inc.
©Wolf Appliance Company, LLC all rights reserved.
Page 19
19
FOLD LINE FOR LOGO PLACEMENT
BOTTOM EDGE OF HOOD
CUT-OUT FOR LOGO PLACEMENT
LEFT OUTER EDGE OF HOOD
Page 20
807573 6/2006
WOLF APPLIANCE COMPANY, LLC P.O. BOX 44848 MADISON, WI 53744 800-332-9513 WOLFAPPLIANCE.COM
Loading...