Wolf 802781, 802782, 802783, 812340, 812341 Installation Guide
...
802781, 802782, 802783, 812340, 812341, 812342, 814020, 815837, 820395
Warming Drawer Handle Installation Instructions
812548 / Rev D / October, 2011Page 1 of 4
CONT
AINS:
ITEM
QTY DESCRIPTION
A 4 Bolt, #10-24 x 3/4''
B 4 Bolt, #10-24 x 1''
C 4 Bolt, #10-24 x 1-1/4''
D 4 Bolt, #10-24 x 1-3/4''
E 4 Bolt, #10-24 x 2-1/4''
F 4 Bolt, #8-32 x 5/8''
G 4 Bolt, #8-32 x 1''
NOTES:
• This front panel kit is designed for and approved only for use with Wolf Warming Drawer (WWD30).
• These handle kits are designed for use with a Wolf Integrated Front Panel Kit #808152
• Please read these instructions carefully before beginning installation.
• For any additional information, refer to the Use and Care Information and Installation instructions included
with model WWD30.
AB C D EFGHI JK L
Fastener Reference
802781 Handle, Tubular 23-1/2” Classic
802782 Handle, Tubular 23-1/2” Carbon
802783 Handle, Tubular 23-1/2” Platinum
812340 Handle Curved 26-7/8” Framed
812341 Handle, Curved 29-3/8” Unframed
812342 Handle, Pro 25-7/8”
814020 Tube Handle, 3/4'' Unframed
815837 Tube Handle, 3/4'' Framed
820395 Tube Handle, 3/4'' Black
ITEM QTY DESCRIPTION
H 4 Bolt, #8-32 x 1 1/4''
I 4 Bolt, #8-32 x 1 3/4''
J 4 Bolt, #8-32 x 2 1/2''
K 4 Washer, 1/4 x 5/8''
L 2 Stud, Mounting
1 Instructions
See Fastener Reference Diagram Below:
802781, 802782, 802783, 812340, 812341, 812342, 814020, 815837, 820395
Warming Drawer Handle Installation Instructions
812548 / Rev D / October, 2011
INST
ALLATION PROCEDURE:
1” Tubular Handles
(Kits 802781, 802782, 802783):
1. Mark custom panel to locate the drill holes using
the center-line dimensions from Figure 1. Drill
four (4) 7/32'' to 1/4'' holes.
2. Counter bore 5/8'' holes to 5/32'' deep so that you
can completely recess the head of the bolt and
washer (See Figure 2).
3. Insert appropriate length bolts (two 1/4'' bolts, but
may vary depending on panel thickness) with
washer(s) through holes into handle (See Figure
2).
4. Tighten the bolts to secure the handle to cabinet
panel.
5. Proceed with panel attachment instructions included with the WWD flush mount panel kit.
3/4” Tubular Handle Framed & Unframed
(Kits 814020, 815837, 820395):
1. Mark custom panel to locate the drill holes using
the center-line dimensions from Figures 3 or 4.
Drill four (4) 7/32'' to 1/4'' holes.
(CONTINUED ON NEXT PAGE)
Page 2 of 4
C
L
19.310
23.750
C
L
15.310
Figure 1. 1'' Handle Dimensions
1-3/8” to 1 3/4”
Figure 2. Decorative Panel Prep for Handle
C
L
26.625
29.375
C
L
25.375
Figure 4. 3/4'' Unframed Handle Dimensions
C
L
24.124
C
L
25.374
26.875
Figure 3. 3/4'' Framed Handle Dimensions
Counter Bore
Bolt
Decorative Panel
(Cross Section View)
Washer
Loading...