Wisenet SMT-2702PVM, SMT-2152PVM, SMT-2151PVM, SMT-2701PVM User Manual

Page 1
Hanwha Techwin America
500 Frank W. Burr Blvd. Suite 43 Teaneck, NJ 07666 Toll Free +1.877.213.1222 Direct +1.201.325.6920 Fax +1.201.373.0124 www.hanwhasecurity.com
LCD PUBLIC VIEW MONITOR
User Guide
SMT-2151PVM & SMT-2701PVM
Page 2
Page 3
LCD Public View Monitor
User Guide
Hanwha Techwin Co., Ltd. All rights reserved.
©2017
Trademark
Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company.
Restriction
Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization.
Disclaimer
Hanwha Techwin
provided. Use of this document and the subsequent results shall be entirely on the use right to change the contents of this document without prior notice.
Please change your password every three months to safely protect personal information and to prevent the damage of the information theft. Please, take note that it’s a user’s responsibility for the security and any other problems caused by mismanaging a password.
Equipment shall be installed in accordance with the latest local/national codes of practice, and standards eg :- UL 1203 Edn. 5, CSA22.2 No30-M1986 Edn1 rearmed 2012, CSA C22.2 No25-1966 rearmed 2014, CSA C22.2 No 60065-03 Edn. 1, UL60065 Edn. 7,
makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be
r’s own responsibility.
Hanwha Techwin
reserves the
Page 4
contents
GENERAL
4
1.3 Before You Begin 5
VESA MOUNTING
41.1 CE Information
41.2 Safety Precautions
MTBF shall be 30,000 hours minimum at 90% condence level and 100% duty cycle continuous operation at 25 C. The calculation does not include LCD panel.
Model
SMT-2151PVM SMT-2152PVM
VESA Spec. of screw hole
100x100 mm 200x100 mm
M4 x 5mm
o
MECHANICAL
FUNCTIONAL
SPECIFICATIONS
7
CONTROLS AND
INDICATORS
8
72.1 Functional Specications
83.1 Connectors
93.2 Control Button
103.3 LED Indication
113.4 Remote Control
113.5 Accessories
SMT-2701PVM SMT-2702PVM
Use appropriate screws to mount VESA bracket (Screw hole: M4 x 5mm), failure to do so may cause serious injury.
Ensure that the VESA bracket has an adequate size mounting plate, screws and/or xings to support the weight of the monitor and bracket to the surface to which it is being attached. Failure to do so may cause serious injury.
If there is any doubt of the suitability of a mount or xing method, a qualied technician should be consulted.
Caution
This 21.5” / 27” PVM is intended to be xed to a surface during use. Use a bracket rated for the weight of the unit. Follow the bracket instructions for xing to a surface.
100x100 mm 200x100 mm
M4 x 5mm
19
Page 5
Mechanical
CABINET
Material: Metal. Finish: Black
DIMENSIONS OF SMT-2151PVM / SMT-2152PVM (21.5” PVM)
Unit: mm(inch)
47(1.8")
503(19.8")
Net Weight: 5.9Kg /13 lbs.
Shipping Weight: 8.0Kg / 17.7 lbs.
Packing Dimension (L x W x H): 628x155x502mm / 24.7x 6.1x 19.7 inch
20(0.8")
361(14.2")
35(1.4")
200(7.9")
100(3.9")
DIMENSIONS OF SMT-2701PVM / SMT-2702PVM (27” PVM)
Unit: mm(inch)
637(25.1")
52(2.0")
20(0.8")
200(7.9")
100(3.9")
100(3.9")
OSD MENU
12
REGULATORY AGENCY
& RELIABILITY
17
MECHANICAL
18
4.1 Main Menu
4.2 Main Adjust
4.3 Color Adjust
4.4 Scan Setting
4.5 Image Adjust (VGA Only)
4.6 Information
4.7 Language
4.8 Setup Menu
4.9 Factory Reset
4.10 Audio Control
12 12
13
CONTENTS
13 14 14 15 15 16 16
175.1 Safety Approvals
175.2 EMI/EMS Emission Approvals
186.1 Cabinet
186.2 Dimensions of SMT-2151PVM, SMT-2152PVM
186.3 Dimensions of SMT-2701PVM, SMT-2702PVM
196.4 VESA mounting
448(17.7")
40(1.6")
Net Weight: 7.7Kgs /17.1 lbs.
Gross Weight: 10.4Kgs / 23 lbs.
Packing Dimension (L x W x H): 769 x 162 x 608mm / 30.2x 6.3x 23.9 inch
18
100(3.9")
Page 6
general
regulatory agency
CE INFORMATION
The product must be installed according to the currently valid installation regulations for EMC to guarantee the designed use and to prevent EMC problems. The device supplied with this manual is according to the EC, EMC Directive, 2014/30/EU & LVD 2014/35/EU
SAFETY PRECAUTIONS
Do not modify the three-prong grounding type monitor power plug in any way.
1.
2.
Operate this unit only from the type of power source indicated on the label.
3.
Do not block or cover ventilation openings on the back or bottom of the monitor cabinet.
4.
Do not place this monitor near a radiator or heating vent.
5.
Do not push objects of any kind through cabinet openings. This may result in re or electrical shock.
6.
Before adding attachments always ask a service technician to perform routine safety tests to determine that equipment is in safe operating condition. Ground potential tests should be part of the routine safety check made by the service technician.
7.
Do not place monitor on an unstable cart, stand, or shelf where it may fall and injure personnel or damage equipment.
8.
Route power cords so that they cannot be walked upon or tripped over. Do not allow anything to rest on the power cord.
9.
Do not install monitor in wet areas, or where it may be exposed to rain or water. Do not spill liquid of any kind on the unit.
10.
Unplug the power cord from the unit before cleaning the display. Use only a damp cloth. Do not use alcohol, spirits, or ammonia to clean the display. DO NOT ATTEMPT TO CLEAN THE INTERIOR OF THIS UNIT- THIS ACTION
MUST BE PERFORMED BY THE SERVICE TECHNICIAN AS REQUIRED DURING NORMAL MAINTENANCE.
11.
Refer all servicing to qualied service personnel. REMOVAL OF BACK COVER BY UNAUTHORIZED PERSONNEL MAY
EXPOSE THE USER TO DANGEROUS VOLTAGES OR OTHER HAZARDS.
12.
Unplug the unit immediately and notify the service technician.
A.
If liquid has been spilled into the display or the display has been exposed to rain or water.
B.
If the unit has been dropped or the cabinet damaged.
C.
If fuses continue to blow.
D.
If the power cord is damaged or frayed.
E.
If a distinct change from normal operation is apparent.
When replacement parts are required, be sure that the service technician uses components specied by the manufacturer which have the same characteristics as the original parts. UNAUTHORIZED SUBSTITUTIONS MAY RESULT
IN FIRE, ELECTRICAL SHOCK OR OTHER HAZARDS.
Upon completion of any service or repairs, ask the technician to perform safety checks to determine that the equipment is in safe operating condition.
WARNING: SERIOUS SHOCK HAZARDS EXIST WITHIN THE COVERS OF THIS MONITOR. DO NOT OPEN THE COVERS
UNDER ANY CIRCUMSTANCES, THERE ARE NO USER SERVICEABLE COMPONENTS INSIDE
4
SAFETY APPROVALS
This series design shall meet the standards of the following domestic and foreign agencies: UL : UL 60950-1
cUL: CAN/CSA C22.2 NO. 60950-1-07
EMI/EMS EMISSION APPROVALS
This series design shall meet following EMI/EMS specications: FCC Compliance: FCC Rules and Regulations, Part 15, subpart B, Class A. CE COMPLIANCE: EN55032 Class A.
EN55024. EN50130-4
OSD MENU
17
Page 7
OSD menu
FACTORY RESET
Press MENU button to recall PVM Monitor to factory default setting.
AUDIO CONTROL
Press MENU button to enter the sub-menu
1. Press / button to select an icon
2. Press MENU button to conrm the selection.
3. Press / button to adjust the value
4. Press MENU button to return
VOLUME – Adjust the PVM Monitor volume. MUTE – Select Audio MUTE ON/OFF.
BEFORE YOU BEGIN
Read these instructions before installing or operating this product. Note: This installation should be made by a qualied service person and should conform to local codes.
This manual provides installation and operation information. To use this document, you must have the following minimum qualications
A basic knowledge of CCTV systems and components
A basic knowledge of electrical wiring and low-voltage electrical connections
Intended use
Only use this product for its designated purpose; refer to the product specication and user documentation.
Customer Support
For assistance in installing, operating, maintaining and troubleshooting this product refer to this document and any other documentation provided.
Conventions Used in this Manual
Boldface or button icons highlight command entries. The following WARNING, CAUTION and Note statements
identify potential hazards that can occur if the equipment is not handled properly:
* WARNING:
Improper use of this equipment can cause severe bodily injury or equipment damage.
** Caution:
Improper use of this equipment can cause equipment damage.
Note: Notes contain important information about a product or procedure.
This apparatus is manufactured to comply with the radio interference. A Declaration of Conformity in accordance with the following EU standards has been made. The manufacturer declares that the product supplied with this document is compliant the provisions of the EMC Directive 2014/30/EU, the CE Marking Directive 93/68 EEC and all associated amendments.
GENERAL
All lead-free products oered by the company comply with the requirements of the European law on the Restriction of Hazardous Substances (RoHS) directive: 2011/65/EU, which means our manufacture
!
processes and products are strictly “lead-free” and without the hazardous substances cited in the directive.
The crossed-out wheeled bin mark symbolizes that within the European Union the product must be collected separately at the product end-of-life. This applies to your product and any peripherals marked with this symbol. Do not dispose of these products as unsorted municipal waste.
* This symbol indicates electrical warnings and cautions.
** This symbol indicates general warnings and cautions.
16
5
Page 8
general
WARNINGS AND CAUTIONS:
To reduce the risk of re or electric shock, do not insert any metallic objects through the ventilation grills or other openings on the equipment.
WARNING
This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO USER-SERVICABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
6
LANGUAGE
Press MENU button to enter the sub-menu
SETUP MENU
Press MENU button to enter the sub-menu
1. Press / button to select an icon
2. Press MENU button to conrm the selection.
1. Press / button to select an icon
2. Press MENU button to conrm the selection.
3. Press / button to adjust the value
4. Press MENU button to return
OSD TIMEOUT – Adjust the OSD timeout OSD BLENDING – Select OSD blending
LOW/MIDDLE/HIGH/OFF BACKLIGHT CONTROL – Select backlight control TIMER/SENSOR/OFF BACKLIGHT TIMER – Set backlight timer 10min~120min, 10min increment/click
LED FLASH – FLASH 1sec(on)/1sec(o) - - OFF/ON LED SWAP – Set LED color GREEN or RED FW. UPDATE (USB) – Plug USB with update FW
then select this icon to update PVM FW CAMERA POWER – Press MENU button to return to the main menu EXIT – Press MENU button to return to the main menu
OSD MENU
15
Page 9
OSD menu
functional specications
IMAGE ADJUST (VGA ONLY)
Press MENU button to enter the sub-menu
INFORMATION
Press MENU button to enter the sub-menu
1. Press / button to select an icon
2. Press MENU button to conrm the selection.
3. Press / button to adjust the value
4. Press MENU button to return
AUTO ADJUST – Press MENU buttons to auto adjust Image Settings H. POSITION – Adjust the horizontal position value manually V. POSITION – Adjust the vertical position value manually
PHASE – Adjust the phase value manually CLOCK – Adjust the clock value manually EXIT – Press MENU button to return to the
main menu
Power Supply
PVM Monitor Power Requirements:
21.5” Voltage: DC 12V-24V Wide Range Current: 2.6A max (12Vdc) or 1.3A max (24Vdc) 27” Voltage: DC 12V-24V Wide Range Current: 3.6A max (12Vdc) or 1.8A max (24Vdc)
Use only a PSU rated at 12Vdc, with a minimum current rating of 2.6A/3.6A; or 24Vdc, with a minimum current rating of 1.3A/1.8A
D-SUB Input
Analog RGB: 0.707Vrms Support VESA Standard Timing
HDMI Input - HDMI Compatible Interface
480i / 480p / 576i / 576p 720p / 1080i / 1080p
EDID
This series of displays support EDID (HDMI input only)
Audio Input
Signal Level: 1.0Vrms
Environmental
Temperature: Operating: 0 Storage: -20oC to +60oC Humidity: Operating: 10% to 85% (non-condensing) Storage: 10% to 95% (non-condensing)
o
C to +40oC
GENERAL & FUNCTIONAL SPECIFICATIONS
7
14
Page 10
controls & indicators
CONNECTORS
DC In
(A)
RJ45
(B)
AUDIO IN
(C)
A. DC IN: DC 12~24V INPUT (DC Jack 5.5mmψ2.5). B. RJ45: IP Camera Video Output C. AUDIO IN: Stereo audio input D. USB: Firmware update E. HDMI: HDMI input F. VGA: D-sub 15pin input
USB
(D)
HDMI
(E)
VGA
(F)
COLOR ADJUST
Press MENU button to enter the sub-menu
SCAN SETTING
Press MENU button to enter the sub-menu
1. Press / button to select an icon
2. Press MENU button to conrm the selection.
3. Press / button to adjust the value
4. Press MENU button to return
COLOR TEMP – Select the color temperature USER/ 6500K / 7500K / 9300K
RED – Adjust the RED value under USER setting GREEN – Adjust the GREEN value under USER setting BLUE – Adjust the BLUE value under USER setting EXIT – Press MENU button to return to the main menu
1. Press / button to select an icon
2. Press MENU button to conrm the selection.
3. Press / button to adjust the value
4. Press MENU button to return
ASPECT RATIO – Select aspect ratio 4:3 or 16:9 UNDERSCAN – Select underscan ON/OFF/USER H.START – Adjust horizontal start value under USER setting H.SIZE – Adjust horizontal size value under USER setting V.START – Adjust vertical start value under USER setting V.SIZE – Adjust vertical size value under USER setting EXIT – Press MENU button to return to the main menu
OSD MENU
8
13
Page 11
OSD menu
MAIN MENU
Press MENU button to enter the sub-menu
Main Adjust Color Adjust Scan Setting Image Adjust Information Language Setup Menu Factory Reset Audio Control Exit
Press / button to select an icon, then press MENU button to conrm the selection.
CONTROL BUTTON (ON THE BACK)
CONTROLS & INDICATORS
IPC Reset access door
IPC SD Card access door
MAIN ADJUST
Press MENU button to enter the sub-menu
12
1. Press / button to select an icon
2. Press MENU button to conrm the selection.
3. Press / button to adjust the value
4. Press MENU button to return
VIVID MODE – Select Vivid mode BRIGHTNESS – Adjust the brightness value CONTRAST – Adjust the contrast value SHARPNESS – Adjust the sharpness SATURATION – Adjust the saturation NR – Set Noise Reduction level DLC – Set Dynamic Luminance Control ON/OFF EXIT – Press MENU button to return to the main menu
(A) “ ” Source button
Press the button to show source menu. Select VGA, HDMI, and CAMERA input.
(B) “ ” Up button
Press the buttons to scrolling the cursor to desired function. Press the buttons to increase the value of selected function in sub OSD menu.
(C) “ ” Down button
Press the buttons to scrolling the cursor to desired function. Press the buttons to decrease the value of selected function in sub OSD menu.
(D) “ ” Menu button
Press the button to show the OSD main menu. As a conrmation key during the OSD operation.
(E) “ ” Power button
Press the button to turn ON or turn OFF the monitor.
9
Page 12
controls & indicators
LED INDICATION REMOTE CONTROL
A B C
POWER: Monitor Power On/O.
MUTE: Audio mute
SOURCE: Select input signal
: OSD menu navigation
OK: OSD conrm/select
EXIT: Exit the OSD menu
MENU: Access OSD menu
INFO: Displays PVM information
CAMERA: Sets camera as display source
HDMI: Sets HDMI input as display source
VGA: Sets VGA input as display source
LOCK: Activates and deactivates remote key lock
Vol. + : Increase audio volume
Vol. -: Decrease audio volume
CONTROLS & INDICATORS
(A) Light sensor: (measures ambient light for auto adjust settings) (B) IR Receiver: (for remote control) (C) LED: (Programmable, attention getting LED)
Notes:
The remote control requires 2xAAA batteries. Ensure batteries are inserted in the correct polarity according to the + and – symbols in the battery compartment.
To avoid damage from possible battery leakage, remove the batteries if you do not plan to use the remote control handset for an extended period of time.
Batteries should last more than 2 years with normal use.
ACCESSORIES
All of the accessories listed below are included with the PVM.
1. 60 Watts 12V power adapter x 1
2. US Power Cord x 1
3. Remote Control x 1
4. DC Terminal x 1
5. Cable Clip x 1
6. AAA battery x 2
7. User’s Manual x 1
10
11
Loading...