Winco Customer Instructions Instruction Manual

other electronic devices.

CUSTOMER INSTRUCTIONS

PLEASE READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE PROCEEDING WITH ASSEMBLY

PLEASE READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE USING THIS PRODUCT.

e-mail: [e-mail] before attempting to use this product; otherwise injury may occur.

Winco assumes no responsibility for damage or injury caused by the

3170B Designer Three Panel Screen

If you have trouble understanding these instructions contact your dealer or Winco customer support, [phone],

1. READ AND FOLLOW ALL DIRECTIONS.

2. NEVER place screen on a cart, table, stand or other objects; Screen could fall and INJURY MAY OCCUR.

3. NEVER place screen near open flame or over a radiator or heat register.

4. NEVER place screen in front of a door or exit sign; or durin g emergency screen could hinder evacuation.

5. SUFFOCATION DANGER to children if vinyl is not attached to screen; Screen could block nose and mouth
and prevent breathing. VINYL SCREEN IS NOT A TOY.

6. DO NOT allow children to play with screen; Screen could fall and INJURY MAY OCCUR.

7. Screen should ALWAYS be position ed on le vel surf ac e.

8. NEVER stand or ride on screen legs; INJURY MAY OCCUR.

9. DO NOT use screen in or with ANY type of vehicle or trailer.

10. DO NOT attach objects to screen frame; Screen can tip over and INJURY MAY OCCUR.

11. Remove from service; Any screen with broken or missing parts, torn vinyl, or other visible damage.

12. USE ONLY WINCO AUTHORIZED REPLACEMENT PARTS.

13. SAVE THESE INSTRUCTIONS for future reference and training.

14. Both small and large magnets can pose dangers to kids and adults. Mishandling of magnets may

cause injury or property damages. Make sure to keep magnets away from people who are wearing
pace makers or other medical devices. Also keep magnets away from CRT monitors, CRT TVs, and

improper assembly, installation or use of these products.

Tools needed:

• Scissors or box cutter

• 5/32 Allen Wrench (provided)

• Phillips screw driver (not provided)

1. After checking your product for any shipping damage, remove all packing material and hardware that was secured for
shipping. Cut tape and/or plastic with scissors, being careful not to damage screen.

LEG INSTALLATION SEE PHOTOS, NEXT PAGE

2. Using a Phillips Screw Driver, Install (2) Screen Leg Reinforcement Tubes (#5) between Leg Frame Assemblies (#3)
using 4-Phillips Head Screws (5A), one on each end, through (#3) into (#5). Leave screws on one Leg Frame
Assemblies (#3) loose to allow assembly to be inserted into Wing/Mid Frame Assembly (#1A).

3. Insert both Leg Frame Assemblies (#3) into the bottom of the Wing/Mid Frame Assembly (#1A).
Line up the holes in (#3) w/ the holes in (#1A).

4. Using the Allen Wrench provided screw in 1-Button Socket Screw (3D), per leg, through (#1A) and into (#3). Tighten 2-
Phillips Head Screws (5A) that were left loose in step 2.

PANEL REPLACEMENT SEE PHOTOS, NEXT PAGE

5. To replace Vinyl Panels (#4), hold the screen by the top Screen Rod (#2A).

6. Next, using the Allen Wrench provided, push in on the small hole just below the Snap Button (#2B).

Re-install (#2A) by repeating the above procedure, then release (#2B) when (#2A) is in place

CARE & MAINTENANCE OF YOUR SCREEN

7. Periodically check all fasteners for tightness.

8. To clean Vinyl Panels use only mild liquid soap and water.

006250 Rev S 02-14-17 SLC

Page 1 of 4

Page 2 of 4

Wrinkles in Vinyl – Storage and/or shipping causes wrinkles in the vinyl of your Winco Screen; This is normal. Please allow

1-2 weeks at room temperature (approx. 70+ degrees) to allow for vinyl to return to original appear an ce.

Items Included with Screen: Qty.

(1A) Wing/Mid Frame Assembly Kit 1
(1B) Domed Plastic Insert 10
(2B) Snap Buttons 4
(2A) Screen Rod 6
(2B) Snap Buttons 12
(3) Leg Frame Assembly 2
(3B) 2” Caster 4
(3C) Caster Insert 4

(3D)

¾” Button Socket Screw 2

(4) 3170 Vinyl Panel 3
(5) Screen Leg Reinforcement Tube 2
(5A) 2” Phillips Head Screw 4
(6) MAGNET,1/2" X 1/8" 2

Visit our website www.wincomfg.com/product-documents/parts-lists for a complete parts list catalog of your chair or

call Customer Service @ 1-800-237-3377 to request it by mail.

006250 Rev S 02-14-17 SLC

Page 3 of 4

GENERAL CARE & CLEANING:

Periodically inspect tightness of all screws, bolts, and nuts.
Winco furnishings are built to provide durable reliable service when properly cared for. In general all of our products

should be 1) Cleaned 2) Rinsed 3) Allowed to air dry. It is important to note that disinfecting a product is not the
same as cleaning the product. Disinfectants alone will not provide adequate cleaning, they do not have grease
or oil cutting properties to remove grime or hair and skin oils. Over time, the appearance and feel and
performance of your upholstery may diminish if not cleaned properly

CLEANING:

Remove grime, hair and body oils; Your furnishings should be cleaned with mild soap & water solution and a damp
cloth on a regular basis. Avoid harsh detergents that could damage the finish of your product. If the furnishing is
disinfected with bleach, it MUST be wiped off using only clean water on a damp cloth and then be allowed to air dry.
Failure to rinse with clean water can result in a build-up of residues over time that can damage your product.

Magnet Disclaimer

Disclaimer – It is required that the buyer rea d a nd unders t a nd t he s e

instructions before us ing the magnet.

Both small and large magnets ca n pose da nge rs to kids and adults.
Mishandling of magnets may cause injury or property damages. Make
sure to keep magnets away from people who are wearing pace makers or
other medical devices. Also keep magnets away from CRT monitors, CRT
TVs, and other electroni c devic e s .

006250 Rev S 02-14-17 SLC

Page 4 of 4

Design, appearance, parts, & construction are subject to change without notice

006250 Rev S 02-14-17 SLC