Winco 8910SH User Manual

8900-8910

Bariatric Treatment Table

CUSTOMER INSTRUCTIONS

PLEASE READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE USING THIS PRODUCT.

If you have trouble understanding these instructions contact your dealer or Winco customer support, (800) 237-33 77

Winco assumes no responsibility for damage or injury caused by improper assembly,

1. READ AND FOLLOW ALL DIRECTIONS.

2. NEVER stand on table or INJURY MAY OCCUR.

3. NEVER allow user to sleep unattended on table or INJURY MAY OCCUR.

4. NEVER leave an unconscious user unattended on table or INJURY MAY OCCUR.

5. DO NOT use table for transporting user in or with ANY type of vehicle or trailer. Winco tables have not been tested

or approved for use by an occupant in any type of vehicle or trailer.

6. NEVER leave an infant or child unattended on table or INJURY MAY OCCUR.

7. DO NOT put hands, feet or clothing into any openings when changing user positions on table. Attendant MUST

confirm that users hands and feet are clear of openings when changing positions or INJUR Y MAY RESULT.

8. Periodically, recheck tightness of all nuts, bolts and screws.

9. USE ONLY WINCO AUTHORIZED REPLACEMENT PARTS.

10. NEVER EXCEED the recommended weight capacity of 1000 lbs. (453.6 kg).

11. SAVE THESE INSTRUCTIONS for future reference and training.

Tools needed:

 Phillips-head screwdriver
 7/16” wrench, (multiple size wrench included)
 Scissors or box cutter
 Cardboard shipping container (stays under table during assembly to protect upholstery)
 - If using powered tools always start hardware together by hand first & wear safety goggles

PLEASE READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE PROCEEDING WITH ASSEMBLY

1. After checking your product for any shipping damage, table needs to be positioned upside-down on cardboard
or protective surface. Remove all packing material and hardware that was secured for shipping. Cut tape on
corners of box so that cardboard will lay flat while you assemble table.

Leg Assemblies (3):

2. You will find (3) Table Legs, in-between or attached-to the Table Frame Rails. Pivot up the (2) Table Legs
on ends of table (see photo). Insert (2) ¼-20 x 2” screws through (2) holes in each Upper Leg Brace and into
(2) threaded holes in the wood of the Upholstered Top.

NOTE: Upper Leg Braces on all Table Legs have (2) holes that need to align with two threaded holes in the
wood of the Upholstered Top.

The center Table Leg must have two sets of holes aligned. Holes in the Upper Leg Brace of the Table Leg
must align with holes in the bottom of table, AND the oval-shaped holes on the legs must align with holes on
both frame rails on the table.

The center Table Leg may need to be rotated 180 degrees so that the above alignment is possi ble.

before attempting to use this product; otherwise injury may occur.

installation, use, or maintenance of these products.

8900-8910 Weight Capacity = 1000 lbs. (453.6 kg.)

SEE “Parts Guide & List” (pg.3) for visual reference during assembly.

Page 1 of 4

006190 REV O Date 06-06-12 JWC

prop

j

j

Page 2 of 4

3. Secure the middle Table Leg to the Table Frame Rails with (2) ¼-20 x 2-1/2” screws & locknuts. Then, insert
(2) ¼-20 x 2” screws through (2) holes in each Upper Leg Brace and into (2) threaded holes in the wood of
the Upholstered Top.

IMPORTANT: DO NOT fully tighten at this time.

Cross-Braces (2):

Before installing:

Make sure that the smooth surface of the welds on the Cross-Braces will face upward (when the table is in
the upright position) prior to fastening to Lower Leg Brace of Table Legs. (IMPORTANT for best appearance
and

4. Cross-brace to End Legs: Place (4) ¼-20 x 1-½” screws into the holes in the Lower Leg Braces and
through the holes on the Cross-braces. Install locknuts (hand-tighten). Heads of screws should face the
ends of table, for better appearance.

5. Cross-brace to Center Leg: Place (2) ¼-20 x 2” screws into the holes in the Lower Leg Brace and through
the holes in BOTH of the Cross-brace. Install locknuts.

6. TIGHTEN ALL nuts & bolts holding the Table Legs to the Table Frame Rails.

7. Install the six (6) Glide Feet into the threaded ends of the table legs.

Additional instructions for 8910 models ----- (8900 model go to step 12)

8. Attach the Face Slot Tube so that one hole is aligned with the center hole of the Upper Leg Brace, (flat side

9. Position the opposite end of the Face Slot Tube over the 1” nylon spacer and the hole in table bottom. Install

10. Install Face Paper Holder using (2) 1” black drywall screws in pre-drilled holes on either side of Face Slot.

11. Install Face Paper Cutter on Table Frame Rail (where desired) opposite Face Paper Holder. Peel backing

HINT: After peeling paper from adhesive tape use damp sponge to moisten tape to allow face paper
cutter to be ad

12. Using at least two people, turn table upright.

13. Place Paper Holder Rod, with paper roll installed, through the (2) Paper Rod Clamps.

14. Adjust the Glide Feet to level the table.

Optional Shelf installation:

15. Double-sided tape has been installed on the top of the Cross-braces.

16. Before removing paper on tape, “test fit” the shelf. Shelf should be centered between outside Table Legs.

17. Once you are certain of where you will position the shelf, peel off the paper to expose adhesive.

18. Carefully position shelf in place on adhesive.

HINT: After peeling paper from adhesive tape use damp sponge to moisten tape to allow face paper
cutter to be ad

Wrinkles in Vinyl – Storage and shipping can cause wrinkles of the vinyl on your Winco table. This is normal.
Please allow 1-2 weeks at room temperature (approx. 70 degrees) to allow for vinyl to expand back to original
appearance.

er shelf installation)

of Face Slot Tube faces table bottom).
two (2) 1-3/4” Panhead Phillips screws through both ends of the Face Slot Tube, then tighten into the

upholstered table top with a Phillips Head Screwdriver.

from tape on back and press cutter firmly into place.

usted during install. Once tape is dry face paper cutter will stay in place.

usted during install. Once tape is dry face paper cutter will stay in place.

Do not over tighten nuts and bolts. Periodically check all fasteners for tightness.

006190 REV O Date 06-06-12 JWC