Winco 8570SH User Manual

Page 1 of 8

8570

Adjustable Headrest Treatment Table

CUSTOMER INSTRUCTIONS

PLEASE READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE USING THIS PRODUCT.

If you have trouble understanding these instructions contact your dealer or Winco customer support, (800) 237-33 77

Winco assumes no responsibility for damage or injury caused by improper assembly,

1. READ AND FOLLOW ALL DIRECTIONS.

2. NEVER stand on table or INJURY MAY OCCUR.

3. NEVER allow user to sleep unattended on table or INJURY MAY OCCUR.

4. NEVER leave an unconscious user unattended on table or INJURY MAY OCCUR.

5. DO NOT use table for transporting user in or with ANY type of vehicle or trailer. Winco tables have not been tested
or approved for use by an occupant in any type of vehicle or trailer.

6. NEVER leave an infant or child unattended on table or INJURY MAY OCCUR.

7. DO NOT put hands, feet or clothing into any openings when changing positions on table. Attendant MUST confirm
that users hands and feet are safe while changing table positions or INJURY MAY RESULT.

8. Periodically, recheck tightness of all nuts, bolts and screws.

9. USE ONLY WINCO AUTHORIZED REPLACEMENT PARTS.

10. NEVER EXCEED the recommended weight capacity of 400 lbs. (181.4 kg).

11. SAVE THESE INSTRUCTIONS for future reference and training.

Tools needed:

 Phillips-head screwdriver
 7/16” wrench (multiple size wrench included)
 Scissors or box cutter
 Cardboard shipping container (stays under table during assembly to protect upholstery)
 - If using powered tools always start hardware together by hand first & wear safety goggles

PLEASE READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE PROCEEDING WITH ASSEMBLY

SEE “Parts Reference” (pg.4) for visual reference during assembly.

1. After checking your product for any shipping damage, table needs to be positioned upside-down on the
cardboard shipping container, or protective surface. Remove all packing material and hardware that was
secured for shipping. Cut tape on corners of box so that cardboard will lay flat while you assemble table.

2. You will find two Welded Leg Assemblies, one is attached to table frames and one is not. (SEE parts guide)

3. Pivot up the attached Welded Leg Assembly, (located on opposite end from the Backrest.)

4. Next, using a Phillips screwdriver, install (2) ¼-20 x 1-½” screws through the upper leg brace of the Welded
Leg Assembly into (2) threaded holes in the wood bottom of Upholstered Top, as shown.

5. Install the unattached Welded Leg Assembly, on the end near the Backrest, as shown in parts guide.

The cross brace needs to be positioned toward “backrest end” of table.

before attempting to use this product; otherwise injury may occur.

installation, use, or maintenance of these products.

8570 Weight Capacity = 400 lbs. (181.4 kg.)

006075 Revision O Date 06-06-12 JWC

Page 2 of 8

6. Install (2) ¼-20 x 2-½” screws and (2) ¼-20 nuts to fasten the unattached Welded leg Assembly to the

Table Frame Rails. Heads of screws should face the sides of table, for better appearance. DO NOT
FULLY TIGHTEN AT THIS TIME.

7. REPEAT Step 4

8. Place (4) ¼-20 x 1-½” screws in (4) holes through the lower leg brace of the Welded Leg Assemblies as

shown. Heads of screws should face the ends of table, for better appearance.

9. Align Welded Brace Assembly (smoothest side up, when the table is in the upright position) with the (4)

screws & holes on both Welded Leg Assemblies and fasten with (4) ¼-20 nuts.

If the Optional Shelf and Reinforced Welded Brace Assembly have been ordered; make sure that the smooth surfa ce
(side with tape) of the Reinforced Welded Brace Assembly will face upward ( when the table is in the upright position)
prior to fastening to Welded Leg Assemblies.

10. TIGHTEN ALL FASTENERS AT THIS TIME. (including the nuts & screws holding the Welded Leg

Assemblies to the Table Frame Rails – see sketch).

11. Install the four (4) Glide Feet completely into the ends of the Welded Leg Assemblies.

12. The release handle for the adjustable back rest, can be installed on the left or the right table frame rail,

depending on user preference.

 Should you wish to change the release handle mounting location, simply remove the (2) Phillips head

screws that attach the handle to the table frame rail and relocate the handle to the opposite table frame
rail and re-install the screws.

13. Using at least two people, turn table upright.

14. Slide the Paper Holder Rod into the (2) Paper Rod Clamps.

15. Adjust one or two of the Glide Feet to level table.

Optional Shelf installation:

16. Double-sided tape has been installed on the Welded Brace Assembly.

17. Before removing paper on tape, “test fit” the shelf. Shelf should be approximately ¼” from edge of Lower

Leg Brace.

18. Once you are certain of where you will position the shelf, peel off the paper to expose adhesive.

19. Carefully position shelf in place on adhesive.

Use damp sponge to moisten tape to allow shelf to be adjusted during install.

After peeling paper from adhesive tape:

Once tape is dry shelf will stay in place.

Operation of Table

006075 Revision O Date 06-06-12 JWC

Page 3 of 8



To raise the Upholstered Backrest, pull black lever on the Remote Release System.



To lower the Backrest, pull the same black lever with one hand and apply pressure to the Backrest

with your other hand until the desired position is achieved, then release the black lever.

Vinyl Strap Adjustment – Should the vinyl strap on your Winco table need to be adjusted, unscrew the screw
that currently holds either side of it in place. Pierce another hole in the strap to give desired tension and re-insert
screw.

Wrinkles in Vinyl – Storage and shipping can cause wrinkles of the vinyl on your Winco table. This is normal.
Please allow 1-2 weeks at room temperature (approx. 70 degrees) to allow for vinyl to expand back to original
appearance.

Do not over tighten nuts and bolts. Periodically check all fasteners for tightness.

ADJUSTING GAS SPRING (cylinder):

1. Remove Cable from Operator.

2. Loosen 11/16” nut on top of Operator.

3. Remove Bow-Tie Cotter Pin from Clevis Pin.

4. Remove Clevis Pin.

5. Turn the entire Operator one full revolution:
Clockwise if backrest does not move when handle is
actuated OR Counter-clockwise if backrest will not stay in
down position.

Finish the adjustment:

6. Re-install the Clevis Pin.

7. Re-install the Bow-Tie Cotter Pin.

8. Tighten the 11/16” locking nut on top of Operator.

9. Re-install cable.

10. REPEAT these steps as needed until proper backrest
action is achieved.

Parts Reference

006075 Revision O Date 06-06-12 JWC