Winco 8510D1 User Manual

Page 1 of 4

8500/8510 Treatment Table

with Cabinets and/or Drawer Modules

CUSTOMER INSTRUCTIONS

PLEASE READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE USING THIS PRODUCT.

If you have trouble understanding these instructions contact your dealer or Winco customer support, (800) 237-33 77

Winco assumes no responsibility for damage or injury caused by improper assembly,

1. READ AND FOLLOW ALL DIRECTIONS.

2. NEVER stand on table or INJURY MAY OCCUR.

3. NEVER allow user to sleep unattended on table or INJURY MAY OCCUR.

4. NEVER leave an unconscious user unattended on table or INJURY MAY OCCUR.

5. DO NOT use table for transporting user in or with ANY type of vehicle or trailer. Winco tables have not been tested or approved for use by an occupant in any type of vehicle or trailer.

6. NEVER leave an infant or child unattended on table or INJURY MAY OCCUR.

7. DO NOT put hands, feet or clothing into any openings on table. Attendant MUST confirm that users hands and feet are safe or INJURY MAY RESULT.

8. Periodically, recheck tightness of all nuts, bolts and screws.

9. USE ONLY WINCO AUTHORIZED REPLACEMENT PARTS.

10. NEVER EXCEED the recommended weight capacity of 400 lbs. (181.4 kg).

11. SAVE THESE INSTRUCTIONS for future reference and training.

Tools needed:

 Phillips-head screwdriver  ½” wrench or ½” socket & ratchet wrench  7/16” wrench (multiple size wrench included)  Scissors or box cutter  -If using powered tools always start hardware together by hand first-

PLEASE READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE PROCEEDING WITH ASSEMBLY

1. After checking your product for any shipping damage, remove all packing material and hard ware that was secured for shipping.

2. Use a ½” wrench or socket, and remove the four (4) bolts that are attaching the table to the skid. (Bolts go through the plastic Threaded Inserts in the ends of the Table Legs, and the shipping skid.

3. Using at least two (2) people, lift the table off of the skid.

4. Install the included Glide Feet into the Threaded Inserts, located in bottom of Table Legs. (see note) NOTE: Turning table on side or upside-down will ease this installation; however, drawers should be removed

first. Please protect your Upholstered Top with cardboard, carpeted floor, etc… when performing this operation. Use of two or more people is HIGHLY recommended.

006065 Rev O Date 06-06-12 JWC

before attempting to use this product; otherwise injury may occur.

installation, use, or maintenance of these products.

8500/8510 Weight Capacity = 400 lbs. (181.4 kg.)

SEE “Parts Reference” (pg.3) for visual reference during assembly.

Page 2 of 4

5. With table in the upright position, adjust the four (4) Adjustable Glide Feet to level the table.

6. Use a Phillips bit screwdriver and a 7/16” wrench to check all screws, nuts, and bolts to ensure they are tight and did not loosen during shipping.

7. Load paper roll onto Paper Holder Rod. Rod must be inserted through Paper Rod Clamps.

Do not over tighten nuts and bolts. Periodically check all fasteners for tightness.

Vinyl Strap Adjustment – Should the vinyl strap on your Winco table need to be adjusted, unscrew the screw and washer that currently holds either side of it in place. Pierce another hole in the strap to give desired tension and re-insert screws.

You may move the strap to a new location by removing the screws in ends of the vinyl strap and re-installing in the new location. (It may be necessary to drill 1/16” pilot holes in the wood table bottom to ease re-installation of screws.)

Wrinkles in Vinyl – Storage and shipping can cause wrinkles of the vinyl on your Win co table. This is normal. Please allow 1-2 weeks at room temperature (approx. 70 degrees) to allow for vinyl to expand back to original appearance.

006065 Rev O Date 06-06-12 JWC

+ 2 hidden pages