WMC50522AW
MICROWAVE OVEN BUILT-IN TRIM KIT
W10434148A
You can be killed or seriously injured if you don't immediately
You
can be killed or seriously injured if you don't
follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
INSTALLATION INSTRUCTIONS
Built-In Trim Kit Models MK2227 MK2220
UL listed for use over any electric or gas built-in oven, up to 30" (76.2 cm) wide
INSTRUCTIONS D’INSTALLATION
GARNITURE ENCASTRÉE POUR FOUR À MICRO-ONDES
Garniture encastrée pour modèles MK2227 MK2220
Homologations UL pour utilisation au-dessus de tous les fours encastrés électriques ou à gaz, jusqu’à 30" (76,2 cm) de largeur
Table of Contents / Table des matières
MICROWAVE OVEN SAFETY ..................................................1
INSTALLATION INSTRUCTIONS.............................................2
Tools and Parts ......................................................................2
Location Requirements..........................................................2
Required Cutout Dimensions.................................................2
Trim Kit Frame Dimensions....................................................2
Electrical Requirements .........................................................3
Prepare Microwave Oven.......................................................3
Prepare Cutout/Cabinet Opening..........................................3
Install the Microwave Oven....................................................4
Install Trim Kit Frame .............................................................5
SÉCURITÉ DU FOUR À MICRO-ONDES...........................................7
INSTRUCTIONS D’INSTALLATION....................................................7
Outillage et pièces.............................................................................7
Exigences d'emplacement................................................................7
Dimensions nécessaires de l'ouverture d'encastrement..................8
Dimensions du cadre de la trousse de garniture..............................8
Spécifications électriques .................................................................8
Préparation du four à micro-ondes...................................................9
Préparation de l'ouverture d'encastrement/dans le placard............9
Installation du four à micro-ondes ..................................................10
Installation du cadre de la trousse de garniture .............................11
MICROWAVE OVEN SAFETY
INSTALLATION INSTRUCTIONS
3"
(7.6 cm)
B
B
D
36"
(91.4 cm)
C
2"
(5.1 cm)
2"
(5.1 cm)
1⁹⁄₁₆"
(4.0 cm)
A
E
1¹⁄₁₆"
(2.7 cm)
1¹⁄₁₆"
(2.7 cm)
B
17¹⁄₈" (43.5 cm)
max.
17" (43.2 cm)
min.
26⁷⁄₈" (68.2 cm)**
29
³⁄₄" (75.6 cm)**
¹³⁄₁₆" (2.1 cm)*
*
2³⁄₈" (6.0 cm)**
25" (63.5 cm)
13¹⁄₁₆
"
(33.2 cm
)
1" (2.5 cm)
18⁷⁄₈"
(47.9 cm)
2¹⁵⁄₁₆"
(7.5 cm)
Tools and Parts
Tools Needed
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools
listed here.
■ Measuring tape
■ Pencil
■ Phillips screwdriver
Parts Supplied (not shown to scale)
Rails (2) Bottom duct Trim kit frame
Short screws (14)
(11 + 3 extra)
■ Drill
■ 7/64" drill bit
Long wood screws (6 - painted)
(4 + 2 extra)
Required Cutout Dimensions
22³⁄₄"
(57.8 cm)
25¹⁄₂" (64.8 cm)
3"
(7.6 cm)
A. Trim kit frame overhang
B. Cutout for lower oven
WidthWidth
NOTES:
■ Height dimension is critical: 17" (43.2 cm) minimum, 17¹⁄₈"
(43.5 cm) maximum.
■ Width and depth measurements have ±1/16" (2 mm)
tolerance.
■ 3" (7.6 cm) minimum dimension is from lower oven cutout
ceiling to microwave oven cutout floor.
■ Trim kit frame extends 1¹⁄₁₆" (2.7 cm) above and below the
cutout opening.
A
Location Requirements
The microwave oven may be installed over a built-in oven. If
installing over a built-in oven, make sure there is a minimum of 3"
(7.6 cm) between the top of the lower oven cutout and the
microwave oven cutout floor.
The microwave oven may also be installed in a cabinet by itself
(without a built-in oven below). For best usability, we recommend
a minimum distance of 36" (91.4 cm) from the floor to the cutout
floor.
Make sure the surrounding cabinetry has clearance to open and
close freely. Allow a clearance of at least 1⁹⁄₁₆" (4.0 cm) below the
cutout floor (3" [7.6 cm] for installation above a built-in oven), and
a clearance of at least 2" (5.1 cm) above the cutout opening.
D. Lower cabinets
E. Floor
2
A. Upper cabinet
B. Microwave oven cutout
C. Lower oven cutout
Trim Kit Frame Dimensions
*27" (68.6 cm) trim kit
**30" (76.2 cm) trim kit
Electrical Requirements
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
GROUNDING INSTRUCTIONS
SAVE THESE INSTRUCTIONS
■
For all cord connected appliances:
The microwave oven must be grounded. In the event of
an electrical short circuit, grounding reduces the risk of
electric shock by providing an escape wire for the electric
current. The microwave oven is equipped with a cord
having a grounding wire with a grounding plug. The plug
must be plugged into an outlet that is properly installed
and grounded.
WARNING: Improper use of the grounding plug can
result in a risk of electric shock. Consult a qualified
electrician or serviceman if the grounding instructions are
not completely understood, or if doubt exists as to whether
the microwave oven is properly grounded.
Do not use an extension cord. If the power supply cord is
too short, have a qualified electrician or serviceman install
an outlet near the microwave oven.
AB C
DE
A
B
C
DE
Observe all governing codes and ordinances.
Required:
■ A 120 volt, 60 Hz, AC only, 15- or 20-amp electrical supply
with a fuse or circuit breaker.
Recommended:
■ A time-delay fuse or time-delay circuit breaker.
■ A separate circuit serving only this microwave oven.
Prepare Microwave Oven
1. Unplug microwave oven before proceeding with installation.
2. Remove any loose items inside microwave oven.
3. Gently turn microwave oven onto its top, with the door facing
forward (toward installer).
4. Align the #33 holes on the microwave oven bottom with the
#33 holes on the rails, as shown, making sure the flanges are
forward and pointing up.
A. Rails (2)
B. Microwave oven bottom
C. Short screws (4)
5. Secure the rails to the microwave oven bottom using four
short screws through the #33 hole sets.
D. Flanges
E. Door
Prepare Cutout/Cabinet Opening
1. On the cutout floor, find and mark the centerline.
2. Place the bottom duct in the opening, with the flange resting
against the bottom front facing of the opening.
A. Cutout floor
B. Centerline
C. Bottom duct
D. Bottom duct flange
E. Front facing
3
3. Align the center arrows on the bottom duct with the centerline
A B
A
B
A
B
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
A
B
drawn in Step 1 above.
A. Bottom duct
B. Center arrows, aligned with centerline
4. Mark the three mounting holes through the bottom duct onto
the cutout floor.
Install the Microwave Oven
1. Gently return microwave oven to its upright position.
2. Position microwave oven near cutout opening.
3. Plug in microwave oven.
4. Align the rails with the rail guides on the bottom duct.
A. Short screws (3)
B. Bottom duct mounting holes
5. Using 7/64" drill, drill pilot holes into the three holes marked in
Step 4.
6. Realign and install the bottom duct with three short screws.
7. Using 7/64" drill, drill pilot holes through the four mounting
holes of the bottom duct flange into the bottom front facing of
the cutout/cabinet opening.
4
A. Bottom duct flange
B. Mounting holes
A. Rail guides
B. Rails
Loading...