Whirlpool WFG715H0EH Dimension Guide

30" (76.2 cm) Freestanding Gas Range

PRODUCT MODEL NUMBERS

WFG540H0A WFG710H0A WFG714HLA

WFG720H0A WFG540H0E WFG715H0E

Type of Gas

Natural Gas:

•This range is factory set for use with Natural gas. See “Gas Conversions” section. The model/serial rating plate is located on the oven frame behind the top right side of the oven door has information on the types of gas that can be used. If the types of gas listed do not include the type of gas available, check with the local gas supplier.

LP gas conversion:

Conversion must be done by a qualified service technician.

No attempt shall be made to convert the appliance from the gas specified on the model/serial rating plate for use with a different gas without consulting the serving gas supplier. See “Gas Conversions” section.

Gas Supply Line

•Provide a gas supply line if 3/4" (1.9 cm) rigid pipe to the range location. A smaller pipe on longer runs may result in insuffient gas supply. With LP gas, piping or tubing size can be 1/2" (1.3 cm)

minimum. Usually, LP gas suppliers deteremine the size and materials used in the system. NOTE: Pipe-joint compounds that resist the action of LP gas must be used. Do not use TEFLON tape.

Flexible metal appliance connector:

•If local codes permit, a new CSA design-certified, 4 to 5 ft (122 to 152.4 cm) long, 1/2" (1.3 cm)

or 3/4" (1.9 cm) I.D., flexible metal appliance connector may be used for connecting range to the gas supply line.

•A 1/2" (1.3 cm) male pipe thread is needed for connection to the female pipe threads of the inlet to the appliance pressure regulator.

•Do not kink or damage the flexible metal tubing when moving the range.

Rigid pipe connection:

The rigid pipe connection requires a combination of pipe fittings to obtain an in-line connection to

the range. The rigid pipe must be level with the range connection. All strains must be removed

from the supply and fuel lines so range will be level and in line.

•Must include a shutoff valve:

The supply line must be equipped with a manual shutoff valve. This valve should be located in the same room but external to the range opening, such as an adjacent cabinet. It should be in a location that allows ease of opening and closing. Do not block access to shutoff valve. The valve is for turning on or shutting off gas to the range.

CABINET OPENING DIMENSIONS

PRODUCT DIMENSIONS

A. 277/8" (70.8 cm) max. depth

		with handle
		B. 36" (91.4 cm) cooktop
		height (max.) with leveling
		legs screwed all the way in*
A		C. 467/8" (119.1 cm) overall
		height (max.) with leveling
		legs screwed all the way in*
		D. 297/8" (75.9 cm) width
B	C	E. 257/16" (64.3 cm) depth.
F		Back of range to front
		of cooktop**
E		F. Model/serial rating plate
		(located on the oven frame
D		behind the top right side of
		the oven door)

IMPORTANT: Range must be level after installation. Follow

the instructions in the “Level Range” section. Using the cooktop as a reference for leveling the range is not recommended.

*Range can be raised approximately 1" (2.5 cm) by adjusting the leveling legs.

**Front of door and drawer may extend further forward depending on styling.

Electrical

A 120 volt, 60 Hz., AC only, 15-amp fused, electrical circuit is required. A time-delay fuse or circuit breaker is also recommended. It is recommended that a separate circuit serving only this range be provided. B

A. Gas supply line

A	B. Shutoff valve “open” position

C. To range

C

†®TEFLON is a registered trademark of E.I. Du Point De Nemours and Company.

Cabinet opening dimensions shown are for 25" (64.0 cm)

countertop depth, 24" (61.0 cm) base cabinet depth and 36" (91.4 cm) countertop height.

IMPORTANT: If installing a range hood or microwave hood combination above the range, following the range hood or microwave hoods combination instructions for dimensional clearances above

the cooktop surface.

A freestanding range may be installed next to combustible walls with zero clearance.

*NOTE: 24" (61.0 cm) minimum when bottom of wood or metal cabinet is covered by not less than 1/4" (0.64 cm) flame retardant millboard covered with not less than No. 28 MSG sheet steel, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper. 30" (76.2 cm) minimum clearance between the top of the cooking platform and the bottom of an uncovered wood or metal cabinet.

					B				A.18" (45.7 cm) upper side cabinet to countertop
							D		B.13" (33 cm) max. upper cabinet depth
					C
									C. 30" (76.2 cm) min. opening width
	A								D. For minimum clearance to top of cooktop, see NOTE *.
					E				E. 301/8" (76.5 cm) min. opening width
			K				M		F. The shaded areas are recommended for installation of rigid gas pipe.
					L				G.11" (27.6 cm)
				G					H.17" (43.2 cm)
									I. 2" (5.1 cm)
		F			H
									J. 41/2" (11.4)
					I				K. 3" (7.6 cm) min. clearance from both sides of range to side wall or
			J						other combustible material.
									L. Grounded outlet
									M.Cabinet door or hinges should not extend into the cutout.
	Because Whirlpool Corporation includes a continues commitment to improve our products,								Dimensions are for planning purposes only. For complete details, see	Ref. W10553363B
	we reserve the right to change materials and specifications without notice.								Installation Instructions packed with product. Specifications subject
										08/10/15
									to change without notice.