Whirlpool W6RXNGFW, W8RXNGMW, W8RXEGMW User Manual

Top Mount Refrigerator
®
PRODUCT MODEL NUMBERS PRODUCT DIMENSIONS
LOCATION REQUIREMENTS
Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation Instructions packed with product. Specifications subject to change without notice.
Ref. 2316016ER
03-18-09
1
/
2
" (1.3 cm)
2" (5.1 cm)
To ensure proper ventilation for your refrigerator, allow for a 1⁄2" (1.3 cm) space on each side. Allow 3" (7.5 cm) of space between overhead cabinets and refrigerator top. Allow at least 1" (2.5 cm) between back of cabinet and the wall. If your refrigerator has an ice maker, make sure you leave some extra space at the back for the water line connections.
If you are installing your refrigerator next to a fixed wall, leave 2" (5.1 cm) minimum on the hinge side (depending on your model) to allow for the door to swing open.
NOTE: Do not install the refrigerator near an oven, radiator, or other heat source, nor in a location where the temperature will fall below 55°F (13°C).
4
1
E
overall
D
top of
cabinet
C
B
not incl.
handle
A
C
D
top of
cabinet
B
A
E
overall
Dimensions “D” and “E” include rollers
extended 3/4" (1.9 cm)
ER6AHKXS ER8AHKXR ER8AHMXR
ER8YHMXS
Electrical: A 115-volt, 60-Hz, AC-only, 15­or 20-amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord.
Water: Connect the ice maker to a cold water line with water pressure between 30 and 120 psi (207 and 827 kPa).
IMPORTANT: The pressure of the water coming out of a reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 30 and 120 psi (207 and 827 kPa).
If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).
Model size "A" "B" "C" "D" "E" 14 cu.ft. 31-1/4" 28" 28-1/8" 62-3/8" 63"
W6RXNGFW (79.4 cm) (71.1 cm) (71.4 cm) (158.4 cm) (160 cm) 16 cu.ft. 29" 28" 28-1/8" 65-3/8" 66"
ER6AHKXS (73.7 cm) (71.1 cm) (71.4 cm) (166.1 cm) (167.6 cm) 18 cu.ft. 30-7/8" 28" 28-1/8" 67-3/8" 68"
ER8AHKXR (78.4 cm) (71.1 cm) (71.4 cm) (171.1 cm) (172.7 cm) ER8AHMXR ER8YHMXS
18 cu. ft. 29-1/8" 28" 28-1/8" 67-3/8" 68" W8RX*GMW (74 cm) (71.1 cm) (71.4 cm) (171.1 cm) (172.7 cm)
Depth Cab. Width Door Width Cab. Height Overall Height
Loading...