Whirlpool UDT518SAFP ENERGY GUIDE

Undercounter Dishwasher

PRODUCT MODEL NUMBERS

UDT518SAFP

Location Requirements

There must be a minimum of 255/8" (65.1 cm) in front of
dishwasher to allow door to open fully.

Countertop

Dishwasher

255/8"

(65.1 cm)

2" (5.1 cm) min.

clearance for door

opening

Electrical Requirements

■ 120 volt, 60 Hz, AC-only, 15 or 20 amp., fused electrical supply

■ Wiring must be 2-wire with ground

We recommend:

■ A time-delay fuse or circuit breaker

■ A separate circuit

Water Supply Requirements

■ A hot water line with 20-120 psi (138-862 kPa) water pressure.

■ 120°F (49°C) water at dishwasher.

3

■

/8" O.D. copper tubing with compression fitting or flexible
stainless steel braided fill line (1/2" minimum plastic tubing is
not recommended).

■ A 90° elbow with

3

/8" N.P.T. external pipe threads on one end.

Do not solder within 6" (15.2 cm) from water inlet valve.

Product Dimensions

22" (59 cm)*

321/2" (82.6 cm) min.

35" (88.9 cm) max.

18"

(45.7 cm)

*To front of door frame

SIDE VIEW

171/2" (44.5 cm min.

18"(45.7 cm) max.

21/2"

(6.2 cm)

Drain Requirements

■ Use the new drain hose supplied with your dishwasher. If this is

not long enough, use a new drain hose with a maximum length
of 10 ft (3.05 m) that meets all current AHAM/IAPMO test
standards, is resistant to heat and detergent, use 5/8" (1.58 cm)
or 7/8" (2.2 cm) inside diameter hose and a coupler to connect
the two hose ends. Secure the connection with 2 clamps.

■ Connect drain hose to waste tee or disposer inlet above drain

trap in house plumbing and 32" (81.3 cm) minimum above the
floor. It is recommended that the drain hose either be looped
up and securely fastened to the underside of the counter, or be
connected to an air gap.

■ Use an air gap if the drain hose is connected to house

plumbing lower than 18" (45.7 cm) above floor.

Air gap

■

Use 1/2" minimum I.D. drain line fittings.

■ Do not connect drain lines from other devices to the

dishwasher drain hose.

REAR VIEW

Because Whirlpool Corporation policy includes a continuous commitment
to improve our products, we reserve the right to change materials and
specifications without notice.

Dimensions are for planning purposes only. For complete details, see
Installation Instructions packed with product. Specifications subject to
change without notice.

Page 1 of 2

W10702387-D-WH

5/16

Cabinet Cutout Dimensions

All surfaces must be
free from instrusions

4"

(10.2 cm)

175/8" (44.8 cm) min.

18" (45.7 cm) max.

* Underside of countertop to floor

323/4" to 341/2"*

(83 cm to 88 cm)

24"

(61 cm)

min.

6"

(15.2 cm)

Cut holes in shaded area of cabinet walls or floor for plumbing
and electrical service.

NOTE: ADA installation, 321/2" (82.5 cm) beneath 34" (86.4 cm)
high countertops may be accomplished by adjusting the toekick
and leveling legs.

Custom Panel Dimensions and Installation

Custom panel should be constructed according to diagram below.

15.35" (39.0 cm)+

12-φ 0.08" (0.2 cm)+

Hole deep 0.39" (0.10 cm)

2.56" (6.5 cm)+

6.79" (17.25 cm)+

17.64" (44.9 cm)+

16.48" (41.8 cm)+

7.05" (17.9 cm)+

6.89" (17.5 cm)+

0.59" (1.5 cm)+

26.77" (68.0 cm)+

1.50" (3.8 cm)+

1.18" (3.0 cm)

17.4" + (44.4 cm)

Install the hook on the custom wood panel and insert the hook into the slot on the outer door of the dishwasher. After positioning the
panel, attach the panel to the outer door with screws and bolts.

Because Whirlpool Corporation policy includes a continuous commitment
to improve our products, we reserve the right to change materials and
specifications without notice.

Dimensions are for planning purposes only. For complete details, see
Installation Instructions packed with product. Specifications subject to
change without notice.

Page 2 of 2

W10702387-D-WH

5/16