Page 1
Proline TDC75
CONTENTS
QUICK REFERENCE GUIDE
PROGRAMME CHART
PREPARING THE LAUNDRY
SELECTING A PROGRAMME AND OPTIONS
STARTING AND COMPLETING A PROGRAMME
CHANGING A PROGRAMME
INTERRUPTING A PROGRAMME
DAILY MAINTENANCE AND CLEANING
INSTRUCTIONS FOR USE
BOOKLET
SAFETY ADVICES BEFORE USING
THE DRYER / CONNECTIONS
ELECTRICAL CONNECTION
SAFETY ADVICES AND GENERAL
RECOMMENDATIONS
DESCRIPTION OF THE DRYER
DOOR REVERSIBILITY / CHILD SAFETY LOCK
HEAT EXCHANGER
TROUBLESHOOTING GUIDE / AFTER-SALES
SERVICE
PAGE
PAGE
PAGE
PAGE
PAGE
PAGE
PAGE
4
5
6
7
8
9
10
3
Page 2
SAFETY ADVICES BEFORE USING THE
DRYER / CONNECTIONS
1. Removing the packaging and check
After unpacking, make sure that the dryer is
•
undamaged. If in doubt, do not use the dryer.
Please contact 0870 5425425.
Keep the packaging materials (plastic bags,
•
polystyrene parts, etc.) out of reach of children, as
they are potentially dangerous.
Remove the protective foil from the control panel.
•
2. Electrical Connections
Electrical connections must be carried out by a
•
qualified technician in compliance with the
manufacturer's instructions and current standard
safety regulations.
Electrical connection must comply with local
•
Electricity Board regulations.
Voltage information, power consumption and the
•
required fuse protection is shown on the rating
plate mounted at the rear of the dryer.
The manufacturer cannot accept any liability for
•
personal injury or damage to property resulting
from failure to adhere to these instructions.
The dryer must be earthed as prescribed by law.
•
Do not use extension leads or multiple adaptors.
•
Before any maintenance on the dryer disconnect it
•
from the mains supply.
Do not operate the dryer if it has been damaged
•
during transport. Please contact 0870 5425425.
Mains cable replacement is only to be carried out by
•
qualified technician or competent person.
After installation access to the mains plug has to be
•
guaranteed, or the all-pole disconnection has to be
possible with a switch.
3. Installation
Do not install your dryer where it can be subject to
•
extreme conditions, such as: poor ventilation,
temperatures around freezing or above 35° C.
Before running the first cycle ensure the water
•
container and heat exchanger are correctly
positioned.
Take care not to install the dryer on a deep-pile
•
carpet.
Take care not to trap the mains cable between the
•
dryer and the wall.
Stability:
When installing the dryer always carefully level the
dryer adjusting the four feet and check the correct
levelling with a spirit level.
Minimum housing dimensions:
Width: 600 mm
Height: 855 mm
Depth: 600 mm
4
Page 3
ELECTRICAL CONNECTION
For your safety please read the following information
Warning: This appliance must be earthed.
The appliance must be connected to a 220-240 volts 50 cycle AC
supply by means of a three pin socket, suitably earthed and should be
protected by a 13 amp fuse in the plug or a15 amp fuse in the
consumer unit.
The appliance is supplied with a moulded 13 amp 3 pin mains plug
fitted with a 13 amp fuse. Should the fuse require replacement, it
must be replaced with a fuse rated at 13 amp and approved to
BS1362.
The plug contains a removable fuse cover that must be refitted when
the fuse is replaced. In the event of the fuse cover being lost or
damaged, the plug must not be used until a replacement cover has
been obtained.
If the moulded mains plug is unsuitable for the socket outlet in your
home or is removed for any other reason, then the fuse should be
removed and the cut off plug disposed of safely to prevent the hazard
of electric shock.
There is a danger of electric shock if the cut off plug is inserted into
any 13 amp socket outlet.
How to wire a 13 amp plug.
Important
The wires in the mains lead on this appliance are coloured in
accordance with the following code:
Green and Yellow - Earth
Blue - Neutral
Brown - Live
As the colours may not correspond with the markings identifying
the terminals in your plug proceed as follows.
The green and yellow wire must be connected to the terminal in the
plug which is marked with the letter E or with the earth symbol or
coloured green and yellow.
The blue wire must be connected to the terminal marked N or
coloured black.
The brown wire must be connected to the terminal marked L or
coloured red.
5
Page 4
SAFETY ADVICES AND GENERAL
RECOMMENDATIONS
Never use and store flammable materials nearby
1. Packing
The packing box may be fully recycled as
confirmed by the recycling symbol .
2. Energy saving tips
Always dry a full load: depending on the type of
•
laundry and the programme/drying time.
By preference use the maximum spin speed allowed
•
by your washing machine, since draining the water
mechanically requires less energy. You will save time
and energy when running your drying cycle.
Do not overdry the laundry.
•
Clean the lint filter after
•
Place your dryer in a room with a temperature
•
between 15° C and 20° C. In case of higher
temperature ventilate the room.
Always select the correct programme/drying time
•
for the load in order to obtain the desired drying
results.
Select the gentle option only with small loads.
•
When drying cotton, for example. dry iron dry and
•
cupboard dry loads together. Start with the iron dry
programme/drying time setting, remove the laundry
to be ironed at the end of that cycle and dry the
remainder of the load on the cupboard dry setting.
3. Disposing of packaging and old Dryer:
The dryer is built from reusable materials. The
dryer must be disposed of in compliance with local
waste disposal regulations.
Before scrapping, cut off the power cable so that
•
the dryer cannot be connected to the mains.
4. Child safety:
Children must not be allowed to play with the dryer.
5. General recommendations:
Always set the programme/time selector knob to
•
the “0” position after use.This prevents the dryer
from being switched on accidentally.
Before cleaning or carrying out maintenance,
•
switch off the dryer and disconnect it from the
mains supply.
To clean the outside of the dryer, use a neutral
•
detergent and a damp cloth.
Do not use abrasive detergents.
•
Do not use inflammable cleansing agents.
•
Do not use the tumble dryer if industrial chemicals
•
have been used for cleaning.
Garments treated or contaminated with flammable
•
cleaning sprays or liquids such as petrol, cooking oil
or aerosol sprays must not be put in this dryer.
Lighters must not be left in pockets.
•
every
drying cycle.
•
the dryer.
Wipe away lint from the door seal and the door
•
using a damp cloth.
If the lint filter mesh is clogged, clean it with water
•
and a soft brush.
Since lint can go through the filter it is necessary to
•
clean, from time to time, the complete filter area
(including below the filter) with a brush, a damp
cloth or with a vacuum cleaner.
EC Declaration of Conformity
This dryer has been designed, constructed and
•
distributed in compliance with the safety
requirements of EC Directives:
73/23/EEC Low Voltage Directive
•
89/336/EEC EMC Directive
•
93/68/EEC CE Marking Directive.
•
This appliance is marked according to the European
directive 2002/96/EC on Waste Electrical and
Electronic Equipment (WEEE).
By ensuring this product is disposed of correctly, you
will help prevent potential negative consequences for
the environment and human health, which could
otherwise be caused by inappropriate waste handling of
this product.
Waste electrical and electronic
products must not be disposed of
with household waste. Please refer to
the retailer from whom you
purchased this item for disposal
instructions .
The dryer must only be used in the household for
•
the prescribed uses.
6
Page 5
DESCRIPTION OF THE DRYER
Work top.
A.
Water Container
B.
Contact pin
C.
Door:
D.
To open the door: pull the
handle.
To close the door: push gently
until closed.
Filter
E.
Child Safety Lock
F.
Button for heat exchanger flap
G.
opening
Heat exchanger
H.
F
A
E
G
C
D
H
B
Reminder - Maintenance and Cleaning
Clean the lint filter at the end of every drying cycle.
Open the door
Pull the filter upwards
Open the filter
Remove lint using a soft brush or your fingertips
Close the filter
Push the filter back into place.
Empty the water container at the end of each drying cycle.
Remove fibers in and around the water evacuation hole at least once per month.
Clean the heat exchanger at least every month (See “HEAT EXCHANGER” chapter).
Wipe away any lint/fluff from the door seal and interior using a damp cloth.
7
Page 6
DOOR REVERSIBILITY / CHILD SAFETY LOCK
Door Reversibility
Unplug the dryer.
A.
Open the door.
B.
Using a spanner, turn the contact pin in the upper part of the door
C.
by 90° and remove it.
Unscrew the 2 screws of the door hinge and remove the door.
D.
Removing the door lock:
E.
Unscrew the 2 screws above and below the door lock system.
Lift the door lock from the bottom, sliding it upwards about
1.5 cm, and remove it.
Reverse the door:
F.
Fasten the door on the desired side with the 2 screws.
Insert the door lock system on the opposite side of the hinge
G.
fixation and push it down 1.5 cm.
Fix the 2 screws above and below the door lock system.
H.
Take care not to reverse the sense of the door lock system. The
I.
child safety must be above the locking mechanism.
Replace the contact pin in the inside of the door (top).
J.
C
C
Child Safety Lock
How to use the child safety lock
Open the door.
1.
Using a coin or a screwdriver, turn the plastic screw (I) clockwise 90°.
2.
Slot vertical: the door cannot be locked.
Slot horizontal: the door can be locked.
8
D
E
I
E
Page 7
HEAT EXCHANGER
Before cleaning or carrying out
maintenance, switch off the dryer.
Clean the heat exchanger at least
every month, proceeding as
follows:
Open the door and press the heat
A.
exchanger flap button on the
bottom of the door entrance.
The heat exchanger flap opens.
B.
Fold the heat exchanger handle
C.
upwards to the horizontal position
and remove the heat exchanger.
Clean the heat exchanger under
D.
running water by turning it around
to reach all sides.
Wipe away dust and lint from the
E.
seals and the heat exchanger.
Remove the lint in the heat
F.
exchanger housing. Keep the
drainage hole (left side in front in
the housing) free from lint.
Replace the heat exchanger in its
G.
housing (TOP or HAUT mark
upwards) and press the handle.
Close the flap.
H.
A
B
C
The heat exchanger aluminium plates
may become discoloured over time.
D
9
Page 8
TROUBLESHOOTING GUIDE / AFTER-SALES
SERVICE
Troubleshooting Guide
If a fault occurs, before contacting our After-
Sales Service, make the following checks to
try and remedy the problem:
Drying takes too long / laundry is not dry enough:
Was the correct programme selected?
•
Was the inserted laundry too wet (Washing
•
machine spin speed less than 800 rpm? When the
spinning speed is less than 800 rpm the water
container fault may occur during the drying cycle)?
Is the lint filter dirty?
•
Is the heat exchanger dirty? (refer to the
•
Instructions for use)
Is the ambient temperature too high?
•
The dryer does not operate:
(after a power failure and/or interruption to the
mains supply, always press the Start button).
Is the plug properly inserted into the mains
•
electricity socket?
Is there a power failure?
•
Has the fuse blown?
•
Is the door properly closed?
•
Has the programme been selected?
•
Has the start delay option been selected?
•
•
Has the
button been pressed?
Start
After-Sales Service
If there is anything about the installation or
operation of this product you do not
understand, please contact our dedicated
Helpline on 0113 2793520.
Please be advised this helpline number is not
for requesting a service call, if you do require
a service call, please contact 0870 5425425.
Container indicator lamp lights on:
Is the lint filter clean?
•
Is the water container empty?
•
Is the water container correctly positioned?
•
Is the heat exchanger clean?
•
Water droplets underneath the dryer:
Is the heat exchanger correctly positioned?
•
Has any fluff on the heat exchanger seal been wiped
•
away?
Has any fluff on the door seal been wiped away?
•
Has the water container been positioned correctly?
•
10
Loading...