WHIRLPOOL SPOW 407 User Manual

BEFORE USING THE APPLIANCE

Please ready all instructions carefully before using this product. When using this appliances, should always
follow this instruction to reduce the risk of fire, electric shock, and injury to person.
Please keep this manual. If you deliver the appliance to other users, do handover this manual together.
These instructions shall also be available on website: www.whirlpool.eu.

SAFETY PRECAUTIONS

• The Installation and service/repair
must be performed by a qualified
technician, in compliance with the
producer's instructions and
following local safety norms. Do
not repair or replace any parts of
the appliance unless it is
specifically written in the user
instructions.

• Do not pull the power supply
cord to remove it from the
socket. Do not twist or press the
power supply cord, and make
sure it is not broken.

• Do not touch the power plug,
circuit breaker and emergency
button when your hands are wet.

• Do not insert your fingers or
foreign substances into the air
inlet/outlet of indoor&outdoor
unit.

• Never block the air inlet or outlet
of indoor and outdoor unit.

• Physically or mentally disabled
people, children and people
without any experience with the
product are only allowed to use

the appliance if they have had
specific training on how to
operate the appliance by a person
responsible for their security and
well-being. The appliance is not
intended for use by disabled
people and very young children
without supervision.

• Children should be supervised to
ensure that they do not play with
the appliance (including remote
control).

• This appliance can be used by
children aged from 8 years and
above and persons with reduced
physical, sensory or mental
capabilities or lack of experience
and knowledge if they have been
given supervision or instruction
concerning use of the appliance in
a safe way and understand the
hazards involved. Children shall
not play with the appliance.
Cleaning and user maintenance
shall not be made by children
without supervision.

4

• This appliance has been made of recyclable or
re-usable material. Scrapping must be carried
out in compliance with local waste disposal
regulations. Before scrapping it, make sure to
cut off the mains cord so that the appliance
cannot be re-used.

• For more detailed information on handling and
recycling of this product, contact your local
authorities who deal with the separate collection
of rubbish or the shop where you bought the
appliance.

SCRAPPING OF PACKAGING

• The packaging can be 100% recycled as
confirmed by the recycling symbol . The
various parts of the packaging must not be
dispersed in the environment, but must be
scrapped in line with local authority regulations.

SCRAPPING OF APPLIANCE

• This appliance is marked according to the
European Directive 2002/96/EC, Waste
Electrical and Electronic Equipment (WEEE).

• By ensuring that this product is disposed of
correctly, you will help to prevent potentially
negative consequences for the environment and
for human health.

• The symbol on the product or on the
documents accompanying the product indicates
that this appliance should not be treated as
household waste, but must be given to the
appropriate local gathering place where electric
and electronic appliances are stored and
recycled.

SAFEGUARDING THE ENVIRONMENT

5

AIR CONDITIONER PRECAUTIONS

Please strictly follow the below
instructions:

• Long and direct exposure to cool
air might be harmful to health. It is
advisable to set the louvers in
order to avoid direct cool air and
deflect it within the room.

• Upon malfunctioning first turn the
appliance off by pressing the
ON/OFF button on the remote
control, then disconnect it from
power supply.

• Always turn off the air conditioner
by remote control first. Do not
use the power supply circuit
breaker or pull off the plug to turn
it off.

• Do not switch the appliance on
and off too often as this can
damage the appliance.

• Do not place any objects on the
outdoor unit.

• Disconnect the air conditioner
from the power supply if it is to
be left unused for a long period of
time or during a thunder/lightning
storm.

• This product contains Fluorinated
Greenhouse Gases covered by the
Kyoto Protocol, the refrigerant
gas being in a hermetically sealed
system. Refrigerant gas: R410a has
a Global Warming Potential
(GWP) 2087.5.

Images in the user instructions are based on external views of standard models, shape and design vary
according to the model.

6

PRODUCT DESCRIPTION

Indoor unit

1. Air Intake

2. Front Panel

3. Display panel

4. Air Outlet

5. Electrical box

6. Filter reset button

7. Vertical Adjustment Louver

8. Horizontal Adjustment Louver

9. Air Filter

10. Remote Control

11. On-off Switch

Outdoor unit

12. Air Intake

13. Pipes and Power Connection Cord

14. Drain Hose

Note: Condensate water drains at COOLING or

DRY operation.

15. Air Outlet

Outdoor unit

Indoor unit

7

CONTROL PANEL DISPLAY INDICATORS
DESCRIPTION

Temperature indicator (1)

Displays set temperature.
It shows "FC" as a reminder to clean the filter.

Running indicator (2)

It lights up during operation.
It flashes during outside unit defrosting.

Timer indicator (3)

It lights up during the set time.
It goes off when timer operation ends.

Sleep indicator (4)

It lights up once sleep mode is set, "Running" indicator will flash for 10 times then the whole display
will light off.

Filter monitor indicator (5)

It flashes when the filter needs to be cleaned.
Filter monitor indicator flashes after 200 hours of usage as reminder to clean the filter.
After filter cleaning, press the filter reset button located on the indoor unit behind the front panel in
order to interrupt the flashing of the filter monitor indicator.

8

REMOTE CONTROL FUNCTIONS
AND INDICATORS

1. ON/OFF BUTTON

Starts and/or Stops the appliance by pressing
this button.

2. MODE BUTTON

Used to select the operation mode.

3. FAN BUTTON

Used to select fan speed in sequence auto,
high, medium or low.

4-5. TEMPERATURE BUTTON

Used to select the room temperature. Used
to set time in timer mode and real time clock.

6. 6TH SENSE BUTTON

Sets or cancels 6th sense operation.

7. SWING BUTTON

Stops or starts horizontal adjustment louver
swinging and sets the desired up/down airflow
direction.

8. SLEEP BUTTON

Sets or cancels Sleep Mode operation.

9. AROUND U BUTTON

Used to set or cancel Around U function.

10. TIMER ON/CLOCK BUTTON

Used to set the current time.
Used to set or cancel the timer on operation.

11 TIMER OFF BUTTON

Used to set or cancel the timer off operation.

12. JET BUTTON

Used to start or stop the fast cooling or
heating.

13. DIM BUTTON

Used to turn on or turn off display light on
indoor unit.

14. POWER SAVE BUTTON

Used to start or stop the power save
operation.

INDICATOR SYMBOLS ON RC DISPLAY

Cooling indicator

Dry indicator

Fan only indicator

Heating indicator

Auto fan speed

High fan speed

Medium fan speed

Low fan speed

6th Sense indicator

Sleep indicator

Around U indicator

Jet indicator

Signal transmission

Display set timer
Display current time

Display set temperature

Power save indicator

ON

OFF

O

STORAGE AND TIPS FOR USING THE
REMOTE CONTROL

How to insert the batteries

1. Insert a pin and gently press down on the
battery cover and push in the direction of the
arrow to remove, as shown.

2. Insert 2 AAA batteries (1.5V) into the
compartment.
Ensure that "+" and "-" polarity is correctly
positioned.

3. Close the battery cover on the remote control.

How to remove the batteries

Remove the battery cover in the direction of the
arrow.
Press the positive pole of the battery softly with
your fingers, then draw the batteries out of the
compartment. All this should be done by adults,
children are forbidden to remove the batteries
from the remote control in order to avoid danger
of swallow.

Disposal of the batteries

To protect natural resources and to promote
material reuse, please separate batteries from
other types of waste and recycle them through
your local, free battery return system.

Precautions

• When replacing the batteries, do not use new
batteries with old batteries, or different types of
batteries as this may cause the remote control
to malfunction.

• If you do not expect to use the remote control
for some time, take the batteries out to prevent
leakage of battery acid in the remote control.

• Operate the remote control within effective
range. Keep the remote control at least 1 meter
from any TV set or HI-FI equipment.

• If the remote control does not work normally,
take the batteries out and reinstall after 30
seconds. If it still does not work install new
batteries.

• To operate the appliance by remote control,
point the remote control at the receiving device
on the indoor unit, to ensure receiving
sensibility.

• To send a message from remote control, the

symbol will flash for 1 second. On receipt
of the message, the appliance will emit a beep.

• The remote control will operate the air
conditioner at a distance of up to 7m.

• Each time the batteries are replaced in the
remote control, the remote control is pre-set at
Heat Pump mode.

Signal receptor

9

10

OPERATING MODE DESCRIPTION

Operation Modes:

1. Selecting mode

Each time MODE button is pressed, the operation
mode is changed in sequence:

COOLING → DRY → FAN ONLY → HEATING

↑

Heating mode is not available for cooling only air
conditioners.
COOLING mode: used to cool your room to let
you feel cool and comfort in the hot season.
DRY mode: used to remove moisture to let you
feel comfort in a humid climate.
FAN ONLY mode: used to ventilate your room,
the air conditioner operates like a fan.
HEATING mode: used to heat your room to let
you feel warm in the cold season.
Note: In order to prevent cool air blowing, 2-5
minutes are necessary to preheat the indoor unit
at HEATING operation start. The indoor fan will
not work during preheating.

2. Setting fan speed

Each time the "FAN" button is pressed, the fan
speed is changed in sequence:

Auto → High → Medium → Low

↑

At "FAN ONLY" mode, only "High","Medium" and
"Low" are available.
At "DRY" mode, Fan speed is set at "Auto"
automatically, "FAN" button is ineffective in this
case.

3. Setting temperature

Press once to raise temperature setting by 1
raise °C
Press once to lower temperature setting by 1

lower °C
Press these two button and hold consistently,
you can change the number quickly.

*Note: Heating mode is NOT available for
cooling only models.

4. Turning on

Press button, when the appliance receives
the signal, the RUNNING indicator of the indoor
unit lights up.

During mode changes wait a few seconds and
repeat the operation if the unit does not respond
at once.
When selection the heating operation, air flow will
start after 2-5 minutes.

Range of available set temperature

*HEATING, COOLING 18°C~32°C

DRY +/-2°C

FAN ONLY unable to set

4

1 2

3

11

AIRFLOW DIRECTION CONTROL

5. Airflow direction control

Horizontal airflow is automatically adjusted to a
certain angle in accordance with the operation
mode after turning on the unit.
The direction of airflow can be also adjusted to
your own requirement by pressing the "SWING"
button of the remote control.

*Heating mode is only available for heat pump
models.

Horizontal airflow control (using the remote
control)

Use the remote control to set the flow angles.

Swinging airflow

Pressing "SWING" button once, the horizontal
adjustment louver will swing up and down
automatically.

Desired direction airflow

Pressing the "SWING" button again to hold the
horizontal adjustment louver when the louvers
swing to a suitable angle as desired.

Vertical airflow control (by hands)

Turn the control rods of the vertical adjustment
louvers to change vertical air flow as shown.

Note: The shape of the unit may look different
from that of the air conditioner you have selected.

A - Do not turn the horizontal adjustment louvers

manually, otherwise malfunction may occur. If
that happens, turn off the unit first and cut off
the power supply, then restore power supply
again.

B - It is better not to let the horizontal adjustment

louver tilt downward for a long time at
COOLING or DRY mode to prevent
condensed water from dripping.

Operation mode Direction of airflow

COOLING, DRY horizontal

*HEATING, FAN ONLY downward

control rod of vertical
adjustment louvers