Because your life is getting busier and more complicated, WHIRLPOOL appliances are easy to use, save
time, and help you manage your home better. To
ensure that you enjoy years of trouble-free operation,
we developed this Use and Care Guide. It is full of
valuable information about how to operate and
maintain your appliance properly and safely. Please
read it carefully.
Also, complete and mail the Product RegistrationCard provided with your appliance. The card helps
us notify you about any new information on
your appliance.
Please record your model’s information.
Whenever you call to request service for your appliance, you need to know your complete model number
and serial number. You can find this information on the
model and serial number label/plate (see the diagram
in the “Parts and Features” section). Also, record the
other information shown in the next column.
Look for these tips!
Look for these Time Smart Tips located
throughout your Use and Care Guide. They
will help you save time and make the most
of your new appliance.
Model Number __________________________________
Serial Number ___________________________________
Purchase Date __________________________________
Dealer Name ____________________________________
Dealer Address __________________________________
Dealer Phone ___________________________________
Keep this book and the sales slip together in a safe place for future reference.
Our Consumer Assistance Center number is toll free.
To find detailed product information, the location of the nearest Whirlpool dealer or authorized servicer, to
purchase an accessory item, or register your appliance on-line, please visit our Web site at
www.WhirlpoolAppliances.com
1-800-253-1301
2
RANGE SAFETY
Your safety and the safety of others is very important.
We have provided many important safety messages in this manual and on your appliance. Always read and
obey all safety messages.
This is the safety alert symbol.
This symbol alerts you to hazards that can kill or hurt you and others.
All safety messages will be preceded by the safety alert symbol and the word “DANGER” or
“WARNING.” These words mean:
You will be killed or seriously injured if you don’t
wDANGER
wWARNING
All safety messages will identify the hazard, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
follow instructions.
You can be killed or seriously injured if you don’t
follow instructions.
wWARNING
Anti-Tip Bracket
Range Foot
Tip Over Hazard
A child or adult can tip the range and be killed.
Connect anti-tip bracket to rear range foot.
Reconnect the anti-tip bracket, if the range is moved.
See the installation instructions for details.
Failure to follow these instructions can result in death or serious burns
to children and adults.
Making sure the anti-tip bracket is installed:
Slide range forward.
•
Look for the anti-tip bracket securely attached to floor.
•
Slide range back so rear range foot is under anti-tip bracket.
•
continued on next page
3
RANGE SAFETY
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electrical
shock, injury to persons, or damage when using
the range, follow basic precautions, including the
following:
WARNING – TO REDUCE THE RISK OF
•
TIPPING OF THE RANGE, THE RANGE MUST
BE SECURED BY PROPERLY INSTALLED
ANTI-TIP DEVICES. TO CHECK IF THE DEVICES
ARE INSTALLED PROPERLY, SLIDE RANGE
FORWARD, LOOK FOR ANTI-TIP BRACKET
SECURELY ATTACHED TO FLOOR, AND SLIDE
RANGE BACK SO REAR RANGE FOOT IS
UNDER ANTI-TIP BRACKET.
CAUTION – Do not store items of interest to
•
children in cabinets above a range or on the
backguard of a range – children climbing on the
range to reach items could be seriously injured.
Proper Installation – Be sure the range is properly
•
installed and grounded by a qualified technician.
Never Use the Range for Warming or Heating
•
the Room.
Do Not Leave Children Alone – Children should
•
not be left alone or unattended in area where the
range is in use. They should never be allowed to
sit or stand on any part of the range.
Wear Proper Apparel – Loose-fitting or hanging
•
garments should never be worn while using
the range.
User Servicing – Do not repair or replace any part
•
of the range unless specifically recommended in
the manual. All other servicing should be referred
to a qualified technician.
Storage in or on the Range – Flammable
•
materials should not be stored in an oven or
near surface units.
Do Not Use Water on Grease Fires – Smother
•
fire or flame or use dry chemical or foam-type
extinguisher.
Use Only Dry Potholders – Moist or damp
•
potholders on hot surfaces may result in burns
from steam. Do not let potholder touch hot
heating elements. Do not use a towel or other
bulky cloth.
DO NOT TOUCH SURFACE UNITS OR AREAS
•
NEAR UNITS – Surface units may be hot even
though they are dark in color. Areas near surface
units may become hot enough to cause burns.
During and after use, do not touch, or let clothing
or other flammable materials contact surface
units or areas near units until they have had
sufficient time to cool. Among those areas are
the cook-top and surfaces facing the cook-top.
Use Proper Pan Size – The range is equipped
•
with one or more surface units of different size.
Select utensils having flat bottoms large enough
to cover the surface unit heating element. The
use of undersized utensils will expose a portion
of the heating element to direct contact and may
result in ignition of clothing. Proper relationship
of utensil to burner will also improve efficiency.
Never Leave Surface Units Unattended at High
•
Heat Settings – Boilover causes smoking and
greasy spillovers that may ignite.
Make Sure Reflector Pans or Drip Bowls Are in
•
Place – Absence of these pans or bowls during
cooking may subject wiring or components
underneath to damage.
Protective Liners – Do not use aluminum foil to
•
line surface unit drip bowls or oven bottoms,
except as suggested in the manual. Improper
installation of these liners may result in a risk of
electric shock, or fire.
Glazed Cooking Utensils – Only certain types of
•
glass, glass/ceramic, ceramic, earthenware, or
other glazed utensils are suitable for range-top
service without breaking due to the sudden
change in temperature.
Utensil Handles Should Be Turned Inward and
•
Not Extend Over Adjacent Surface Units – To
reduce the risk of burns, ignition of flammable
materials, and spillage due to unintentional
contact with the utensil, the handle of a utensil
should be positioned so that it is turned inward,
and does not extend over adjacent surface units.
Do Not Soak Removable Heating Elements –
•
Heating elements should never be immersed
in water.
– SAVE THESE INSTRUCTIONS –
4
IMPORTANT SAFETY INSTRUCTIONS
RANGE SAFETY
Do Not Cook on Broken Cook-Top – If cook-top
•
should break, cleaning solutions and spillovers
may penetrate the broken cook-top and create a
risk of electric shock. Contact a qualified technician immediately.
Clean Cook-Top With Caution – If a wet sponge
•
or cloth is used to wipe spills on a hot cooking
area, be careful to avoid steam burn. Some
cleaners can produce noxious fumes if applied
to a hot surface.
Use Care When Opening Door – Let hot air or
•
steam escape before removing or replacing food.
Do Not Heat Unopened Food Containers –
•
Build-up of pressure may cause container to
burst and result in injury.
Keep Oven Vent Ducts Unobstructed.
•
Placement of Oven Racks – Always place oven
•
racks in desired location while oven is cool. If
rack must be moved while oven is hot, do not let
potholder contact hot heating element in oven.
DO NOT TOUCH HEATING ELEMENTS OR
•
INTERIOR SURFACES OF OVEN – Heating
elements may be hot even though they are dark
in color. Interior surfaces of an oven become hot
enough to cause burns. During and after use, do
not touch, or let clothing or other flammable
materials contact heating elements or interior
surfaces of oven until they have had sufficient
time to cool. Other surfaces of the appliance may
become hot enough to cause burns – among
these surfaces are oven vent openings and
surfaces near these openings, oven doors, and
windows of oven doors.
For self-cleaning ranges –
Do Not Clean Door Gasket – The door gasket is
•
essential for a good seal. Care should be taken
not to rub, damage, or move the gasket.
Do Not Use Oven Cleaners – No commercial oven
•
cleaner or oven liner protective coating of any kind
should be used in or around any part of the oven.
Clean Only Parts Listed in Manual.
•
Before Self-Cleaning the Oven – Remove broiler
•
pan and other utensils.
For units with ventilating hood –
Clean Ventilating Hoods Frequently – Grease
•
should not be allowed to accumulate on hood
or filter.
When flaming foods under the hood, turn the fan
•
off. The fan, if operating, may spread the flame.
– SAVE THESE INSTRUCTIONS –
5
PARTSAND FEATURES
This section contains captioned pictures of your range. Use them to learn where all parts and
features are and what they look like. Use the page references to help you quickly find out more
about the part or feature you are interested in.
(Model RF360PXE shown)
Oven vent
(p. 22)
Plug-in coil element
with one-piece
reflector bowl
(pp. 8, 28, 29, 30)
Anti-tip bracket
(p. 23)
Model and
serial number
plate
(behind left side
of storage drawer)
Manual oven light switch
OFF
HI
OFF
ON
CLOSE DOORCLOSE DOOR
BAKE
BROIL
SELF-CLEANING OSELF-CLEANING OVEN
START ?
OFF
PREHEAT
CLEAN
HI
LO
2
OFF
HI
3
LO
8
4
2
3
5
7
PUSH TO TURN
6
4
5
DOOR LOCKEDDOOR LOCKED
8
7
6
TEMP
AUTO
CUSTOM
CLEAN
BROIL
BAKE
LO
2
3
4
OFF
START
CANCELCANCEL
ENTERENTER
5 SEC5 SEC
HI
8
LO
8
2
7
7
6
3
5
6
PUSH TO TURN
4
5
(Model RF360PXE)
(p. 37)
Control panel
(pp. 8, 28)
Automatic oven
light switch
(p. 37)
Broil element
(not shown)
(p. 18)
Bake element
(p. 16)
Removable
storage drawer
(p. 24)
NOTE: Window on Model RF360PXE only.
CONTROLPANEL
Surface heating
indicator light
6
(lights up when a
coil element is on)
OFF
LO
2
3
HI
8
7
4
PUSH TO TURNPUSH TO TURN
6
5
Left front
control knob
OFFOFF
LO
2
3
HI
8
7
4
6
5
Left rear
control knob
Electronic
oven control
START ?
PREHEAT
CLEAN
BAKE
BROIL
CLOSE DOOR
DOOR LOCKED
BAKE
CUSTOM
BROIL
AUTO
CLEAN
Coil element marker
(shows which coil element
you are setting)
ON
SELF CLEANING OVEN
START
TEMP
OFF
CANCEL
ENTER
5 SEC
LO
2
3
HI
4
6
5
Right rear
control knob
8
7
OFF
LO
2
3
HI
8
7
4
6
5
Right front
control knob
PARTS AND FEATURES
(Model RF364PXE shown)
Oven vent
(p. 22)
CLEANTOP
®
ceramic glass
cooktop
(pp. 10, 33)
Surface cooking area
(pp. 10, 33)
Anti-tip bracket
(p. 23)
Model and serial
number plate
(behind left side
of storage drawer)
Manual oven
OFF
HI
OFF
ON
CLOSE DOORCLOSE DOOR
BAKE
BROIL
SELF-CLEANING OSELF-CLEANING OVEN
START ?
OFF
PREHEAT
CLEAN
HI
LO
2
OFF
HI
3
LO
8
4
2
3
5
7
PUSH TO TURN
6
4
5
DOOR LOCKED
8
7
6
TEMP
AUTO
CUSTOM
CLEAN
BROIL
BAKE
LO
2
3
4
OFF
START
CANCEL
ENTER
5 SEC
HI
8
LO
8
2
7
7
6
3
5
6
PUSH TO TURN
4
5
light switch
(Model RF364PXE)
(p. 37)
Control panel
(pp. 8, 28)
HOT SURFACE
Automatic oven
light switch
(p. 37)
Broil element
(not shown)
(p. 18)
Bake element
(p. 16)
Removable
storage drawer
(p. 24)
NOTE: Window on Model RF364PXE only.
CONTROLPANEL
Surface heating
indicator light
(lights up when a surface
cooking area is on)
LO
OFF
LO
2
3
HI
4
6
5
2
3
8
7
4
PUSH TO TURNPUSH TO TURN
OFFOFF
HI
8
7
6
5
Electronic
oven control
START ?
PREHEAT
CLEAN
BAKE
BROIL
CLOSE DOOR
DOOR LOCKED
BAKE
CUSTOM
BROIL
AUTO
CLEAN
Surface cooking
area marker
(shows which surface cooking
area you are setting)
ON
SELF CLEANING OVEN
START
TEMP
OFF
CANCEL
ENTER
5 SEC
LO
2
3
HI
8
7
4
6
5
OFF
LO
2
3
HI
8
7
4
6
5
Left front
control knob
Left rear
control knob
Right rear
control knob
Right front
control knob
7
USING YOUR RANGE
To get the best cooking results, you should use your range the correct way. This section tells you
what you need to know to use your range safely and efficiently.
USINGTHESURFACECOOKINGAREAS
Using the control knobs
Push in the control knobs before turning them to a
setting. You can set
them anywhere between
HI and OFF.
Turn off all controls when done cooking.
Failure to do so can result in death or fire.
Surface cooking area heat settings
Use the following chart as a guide.
wWARNING
Fire Hazard
SETTING
HI
6-8
5
2-4
LO
RECOMMENDED USE
To start foods cooking.
•
To bring liquids to a boil.
•
To hold a rapid boil.
•
To fry chicken or pancakes.
•
For gravy, pudding, and icing.
•
To cook large amounts of
•
vegetables.
To keep food cooking after
•
starting it on a higher setting.
To keep food warm until it’s
•
ready to serve.
Easy ways to save energy
Match the pan to the surface cooking
•
area size.
The pan should have a flat bottom,
•
straight sides, and a well-fitting lid.
To help shorten your cooking time, use
•
the least amount of liquid possible.
Preheat your pots and pans only when
•
recommended and for the shortest time
possible.
Start your food on a higher heat setting,
•
then turn the control to a lower setting to
finish cooking.
Place a filled pan on the surface cooking
•
area before turning it on.
Coil element model: Keep your reflector
•
bowls clean for best heat reflection.
8
USINGTHESURFACECOOKINGAREAS(CONT.)
USING YOUR RANGE
Using cookware
Use the correct cookware to prevent damage to
•
the surface cooking area, cooktop, wiring, and
surrounding areas.
If the cookware is too small for the surface
•
cooking area or the bottom is not flat, the surface
cooking area could stay glowing red for an
extended length of time causing damage to the
range.
If you start cooking on high, it is important to turn
•
the control down to a lower setting to complete
cooking.
The surface cooking area could overheat or be
•
damaged if a pot has boiled dry or has been left
empty on a hot surface cooking area.
Using the right cookware
makes a big difference
Flat bottomed cookware, including woks,
•
canners, and teakettles, will provide
better contact with the surface cooking
area and provide the best cooking results.
Warped, dented, and ribbed-bottomed
•
cookware can result in uneven cooking
due to incomplete contact with the
surface cooking area.
Cookware that has been designed with
•
slightly indented bottoms or small
expansion channels can be used.
Choose medium to heavy gauge
•
(thickness) cookware.
The pan material (type of metal or glass)
•
affects how quickly and evenly the
pan heats.
Home canning information
To protect your range:
Use flat-bottomed canners/pans for best results.
•
1"1"
cooking area
centered correctly, trap heat and can cause
damage to the cooktop.
Do not place your canner on 2 surface cooking
•
When canning for long periods of time, alternate
•
use of the surface cooking areas between batches
to allow the areas to cool down, or prepare food in
small batches.
On coil element model, keep your reflector bowls
•
clean so that they will always reflect heat well.
Refer to your canner manual for specific
•
instructions.
PanSurface
Use the largest sur-
•
face cooking area for
best results. Also, use a
canner/pan that you can
center over the surface
cooking area and that
does not extend more
than one inch outside
the surface cooking
area. Large diameter
canners/pans, if not
areas at the same time.
Too much heat will build
up and damage the
cooktop.
Start with hot water.
•
This reduces the time
the control is set on
high. Reduce the heat
setting to the lowest
position needed to
keep water boiling.
Optional canning kit
(Coil element models)
Most water-bath or pressure canners have large
diameters. If you do canning with them at high heat
settings for long periods of time, you can shorten
the life of regular coil elements. This can also
damage the cooktop. If you plan to use the cooktop
for canning, we recommend the installation of a
Canning Kit. Order the kit (Part No. 242905) from
your Whirlpool dealer or authorized Whirlpool
service company.
9
USING YOUR RANGE
USINGTHESURFACECOOKINGAREAS(CONT.)
Using the ceramic glass cooktop
(Ceramic glass cooktop models)
Cooking on the ceramic glass cooktop is similar to
cooking on coil elements.
There are, however, a
few differences:
The surface cooking
•
area will glow red when
the element is turned
on. You will see the
HOTHOT SURF SURFACEACE
temperature setting you chose.
Do not cook foods directly on the cooktop.
•
Do not cook popcorn that comes in prepackaged
•
aluminum containers on the cooktop. The
container could leave aluminum marks on the
cooktop that cannot be removed completely.
Lift pots and pans onto and off of the cooktop.
•
Sliding pots and pans on the cooktop could leave
marks that are difficult to remove or could leave
permanent marks.
Dropping a heavy or hard object on the cooktop
•
could crack it. Be careful when using heavy
skillets and large pots. Do not store jars or cans
above the cooktop.
Do not use the cooktop as a cutting board.
•
Do not allow anything that could melt, such as
•
plastic or aluminum foil, to come in contact with
the cooktop while it is hot.
element cycling on and
off – even on the HI
setting – to help the
area stay at the
Sugary spills and soils can cause pitting. See
•
“Cleaning the ceramic glass cooktop” in the
“Caring for Your Range” section for more
information.
Wiping off the cooktop before and after each use
•
will help keep the surface free from stains and give
you the most even heating. See “Cleaning the
ceramic glass cooktop” in the “Caring for Your
Range” section for care and cleaning suggestions.
Using cookware on
ceramic glass cooktops
Check for rough spots on the bottom of
•
your metal or glass cookware which could
scratch the ceramic glass surface.
Make sure the bottoms of pots and pans
•
are clean and dry before using them. Food
and water particles left on the bottoms
can leave deposits on the cooktop when
it is heated.
NOTE:Do not leave empty cookware, or
cookware which has boiled dry, on a hot
surface cooking area. The cookware could
overheat, causing damage to itself or the
surface cooking area.
Hot surface indicator light
(Ceramic glass cooktop models)
The Hot Surface Indicator Light on the cooktop
HOT SURFACE
10
will glow when a surface cooking
area becomes too hot to touch. The
Indicator Light will continue to glow as
long as the surface cooking area is too
hot to touch, even after it is turned off.
POSITIONINGRACKSANDPANS
USING YOUR RANGE
General guidelines
Follow this section carefully to get the best
cooking results.
Before turning on the oven, place oven racks
•
where you need them.
To move a rack, pull it out to the stop, raise the
•
front edge, and lift it out.
Be sure the rack(s) is level.
•
Use pot holders or oven mitts to protect your
•
hands if rack(s) must be moved while the oven
is hot.
When baking/roasting with 1 rack, place the
•
rack so the top of the food will be centered in
the oven.
When baking/roasting on 2 racks, position racks
•
in oven to allow good circulation of air around all
the food.
Do not place items on the oven door when it
•
is open.
Rack placement for specific foods:
FOOD
Frozen pies, large
roasts, turkeys, angel
food cakes
Bundt cakes, most
quick breads, yeast
breads, casseroles,
meats
Cookies, biscuits,
muffins, cakes,
nonfrozen pies
NOTE: For information on where to place your rack
when broiling, see “Broiling guide” later in this
section.
RACK POSITION
1st or 2nd rack
guide from bottom
2nd rack guide
from bottom
2nd or 3rd rack
guide from bottom
Using insulated bakeware, ovenproof
glassware, and dark metal pans
When baking with insulated cookie sheets
•
or baking pans, place them in the bottom
third of the oven. You may need to increase the recommended baking times,
so test for doneness before removing from
the oven.
When using ovenproof glassware or dark
•
bakeware, reduce the oven temperature
by 25°F but use the same baking time.
Because these pans absorb heat, producing darker bottom browning and crispier
crusts, place the rack in the center of the
oven. When baking pies and bread, you
can use the temperature suggested in
the recipe.
11
USING YOUR RANGE
FORBESTAIRCIRCULATION
Hot air must circulate around the pans in the oven
for even heat to reach
all parts of the oven.
This results in better
baking.
Place the pans so
•
that one is not directly
over the other.
For best results, allow
•
11⁄2-2 inches of space
around each pan and
between pans and
oven walls.
For best baking results, bake 1 sheet of cookies
•
at a time.
USINGALUMINUMFOILFORBAKING
Use aluminum foil to catch spillovers from pies
or casseroles:
Place the foil on the oven rack below the rack
•
with the food. Turn up
the foil edges and make
sure the foil is about
1 inch larger all around
than the dish holding
the food.
Do not cover the entire
•
rack with aluminum foil.
It will reduce air circulation and give you poor
cooking results.
Where to place pans:
WHEN YOU HAVE
1 pan
2 pans
3 or 4 pans
Do not line the oven bottom or the entire oven rack
•
with foil or other liners. It could affect the quality of
your baking.
PLACE
In center of the oven rack.
Side by side or slightly
staggered.
In opposite corners on
each oven rack. Stagger
pans so no pan is directly
over another.
12
THEELECTRONICOVENCONTROL
USING YOUR RANGE
ON
AUTO
CLEAN
Indicator lights
(see below)
Auto clean pad
(p. 26)
Bake pad
(pp. 14, 17)
BAKE
BROIL
START ?
PREHEAT
CLEAN
CLOSE DOOR
DOOR LOCKED
CUSTOM
BAKE
Custom broil
pad
(pp. 19, 20)
BROIL
Display
When you first plug in the range, “PF” will appear
•
on the display until you press any command pad.
If “PF” again appears on the display, your electricity was off for a while. You will need to reprogram
any temperature adjustments you may have
made. See the “Adjusting the oven temperature
control” section.
When you are using the oven, the display will
•
show preheat times and temperature settings.
When you are not cleaning or cooking with the
•
oven, the display will be blank.
When setting a function, if you do not press the
•
start/enter pad within 5 seconds, the Start?
indicator light will flash. If you do not press the
start/enter pad within 5 minutes, the function
will be canceled.
Indicator lights
An indicator light to the left of the display lights up
when you are in a setting. An indicator light also
lights up to tell you when the door is locked. An
indicator light on the display lights up when the
oven is on.
Electronic
display
SELF-CLEANING OVEN
TEMP
Temperature
pads
(pp. 14, 17, 19, 20)
START
ENTER
OFF
CANCEL
5 SEC
Start /enter pad
(p. 14)
Of f/cancel pad
(p. 14)
Using the control lock
The control lock lets you disable the control panel
command pads. Control lock comes in handy when
you want to prevent others from using the oven.
NOTES:
You can only use control lock when the oven is
•
not in use or the control has not been set.
Set the control lock when cleaning the control
•
panel to prevent yourself from accidentally turning
on the oven.
You must reset the control lock if the power goes
•
out for more than 1 second.
To lock the control panel:
Press and hold the start/enter pad for 5 seconds.
You will hear a single tone and “Loc” will
START
ENTER
5 SEC
To unlock the control panel:
Press and hold the start/enter pad for 5 seconds.
START
ENTER
5 SEC
appear on the temperature display for
5 seconds. “Loc” will then appear whenever a command pad is pressed.
A single tone will sound and “Loc” will
disappear from the temperature display.
13
USING YOUR RANGE
ON
STARTING/CANCELINGAFUNCTION
After setting a function for the first time, you must
press the start/enter pad to start the
START
ENTER
5 SEC
function.
BAKING/ROASTING
1. Place the racks where you need them in the oven.
For more information, see the “Positioning racks
and pans” section.
The off/cancel pad will cancel any function except
for the control lock.
OFF
CANCEL
Front of rack
Rear of rack
2. Choose the bake setting.
The bake indicator light will light up.
3. Set the temperature (optional).
Do this step if you want to set a temperature
other than 350°F. Press ▲ to raise the temperature or ▼ to lower the temperature in 5°F
amounts. You can set a temperature anywhere
from 170°F to 500°F. Use these pads until the
temperature you want shows on the display.
PRESSYOU SEE
BAKE
PRESSYOU SEE
TEMP
(example for bake at 375°F)
ON
14
Loading...
+ 30 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.