OBU 206 S
99
TABLE OF CONTENTS GB
INSTALLATION
PAGE
100
ELECTRICAL CONNECTION
PAGE
102
BEFORE USING THE APPLIANCES
PAGE
103
PROTECTING THE ENVIRONMENT
PAGE
103
PRECAUTIONS AND GENERAL
RECOMMENDATIONS
PAGE
103
ENERGY SAVING TIPS
PAGE
104
OVEN ACCESSORIES
PAGE
105
COOKTOP ACCESSORIES
PAGE
105
COOKING CHARTS
PAGE
106
CLEANING THE OVEN AND ITS
ACCESSORIES
PAGE
107
CARE AND MAINTENANCE OF
CONVENTIONAL ELECTRIC COOKTOPS
PAGE
109
CARE AND MAINTENANCE OF
GLASS-CERAMIC COOKTOPS
PAGE
109
TROUBLESHOOTING GUIDE
PAGE
109
AFTER-SALES SERVICE
PAGE
110
DECLARATION OF CONFORMITY CE
PAGE
110
54662-gb.fm5 Page 99 Thursday, March 22, 2001 5:40 PM
100
Technical information for the installer
OVEN
•
After removing the oven from its packaging, before
making the connections place it on the polystyrene
foam base to protect it from damage.
•
Do not attempt to lift the oven by the handle.
Lift at the sides as shown in the figure (se e arrow).
•
Check that the appliance has not been d amaged in
transit.
•
Oven dimensions and kitchen unit dimensions are
shown in the opposite figure.
•
Kitchen units in contact with the oven must be he at
resistant (80° C).
•
If plastic laminates or cement are not sufficiently
heat-resistant, warping, bubbling or detachment of
the finish may result.
•
For correct ventilation, follow the ventilation
opening directions shown in the figure (at least
500 x 80 mm). Also provide for at least 5 mm
clearance between the top of the oven and the
lower edge of the worktop. This space must not
be obstructed by cross rails or other structural
elements.
•
During oven installation, care must be taken to
ensure that the sides are not touching the front
edges of the housing or adjacent drawers and
doors (see picture).
•
Carry out the electrical connections between
cooktop and oven (see chapter “Electrical
connection”).
•
Secure the oven to the kitchen unit with screws
(A)
as shown.
INSTALLATION
No contacts
54662-gb.fm5 Page 100 Thursday, March 22, 2001 5:40 PM
101
Cooktop
• The cooktop must be set into a worktop
between 20 mm and 50 mm thick.
There must be nothing between the cooktop
and the oven (cross rails, brackets, etc.).
• If the cooktop is to be installed next to a
column unit, leave a distance of at least
100 mm from the edge of the cooktop to the
side of the column unit.
•
Cut an opening in the worktop of the dimensions
shown in the Product Description Sheet supplied
separately.
•
If not already present, fit the supplied seal to the
cooktop flange after cleaning the contact area as
shown in the figure.
Cooktop with electric hotplates
• If the worktop is made of wood, fit the supplied
clips.
1.
Position the 4 spring clips
(B)
and fit them in their
locations on the underside of the cooktop.
2.
Fit the cooktop into the worktop.
• If the worktop is made of marble, plastic,
ceramics, natural stone, etc.,
the cooktop must be
secured with brackets
(C)
code 4819 310 18528
(to be requested from After Sales Service).
1.
Position the brackets over the holes and secure
them with the supplied screws.
2.
Fit the cooktop into the worktop.
Glass-ceramic cooktop
N.B.:
Remove the protective film before installing the
cooktop.
• If the worktop is made of wood,
use the supplied
spring clips and screws.
1.
Position the 4 clips
(D)
as shown and at the
specified dimensions.
2.
Secure the clips using screws
(E).
3.
Fit the cooktop into the worktop.
• If the worktop is made of marble, plastic,
ceramics, natural stone, etc.
, the cooktop must
be secured with brackets
(F)
code 4819 404 78697
(to be requested from After Sales Service).
1.
Fit the cooktop into the worktop.
2.
Position the 4 brackets
(F)
as shown in the figure,
in accordance with the thickness of the worktop.
3.
Fix the 4 screws
(G)
in holes
(H).
INSTALLATION
54662-gb.fm5 Page 101 Thursday, March 22, 2001 5:40 PM
102
Connecting the oven to the power supply
•
Make sure that the voltage shown on the rating
plate is the same as the power supply voltage in
your home. The rating plate is on the front edge of
the oven cavity (visible with oven door open).
•
Use a type H05RR-F power cord (minimum
length 800 mm).
• Warning: All the oven’s components operate at
230-240 V. When using a 400 V connection,
make sure that the voltage reaching the oven is
230-240 V, as illustrated in the side table.
Interconnecting cooktop and oven
•
Before connecting the oven to the power supply,
check that the cooktop is among the ones listed in
the cooktop/oven pairing product sheet.
Connect the 3 pole and 4 pole connectors to the
respective connectors on the oven.
•
The 3 pole connectors (
H
) is located at the rear
right hand side of the control panel, the 4 pole
connector (
J
) is located at the top of the oven in the
left hand corner (see figure).
•
Connect the yellow/green striped earth wire ( )
(
K
) from the cooktop to the screw located near the
3 pole connector.
WARNING: DO NOT CONNECT TO THE
POWER SUPPLY BEFORE YOU HAVE
FINISHED CONNECTING THE OVEN AND
COOKTOP.
•
Mount the oven in the kitchen unit.
Make sure the power cord is not trapped.
ELECTRICAL CONNECTION
Conductors X
number
Connection
1N+
~
H05 RR-F 3X4 mm²
2N+
~
H05 RR-F 4X2.5 mm²
3+
~
H05 RR-F 4X2.5 mm²
3N+
~
H05 RR-F 5X1.5 mm²
• Make sure the appliances are installed
and connected to the electricity supply
by a qualified technician in accordance
with the manufacturer’s instructions and
in compliance with local regulations.
• The installer is responsible for the correct
electrical connection of the appliances
and the observance of the relative safety
regulations.
• The appliance must be connected to the
electricity supply by means of an all-pole
disconnect switch with minimum contact
gap of 3 mm.
• The appliances must be earthed by law.
• Do not use multiple plug adapters or
extension leads.
• After the appliances have been installed,
the electrical components must be
inaccessible.
54662-gb.fm5 Page 102 Thursday, March 22, 2001 5:40 PM
Loading...