The following service update information is provided to make you more knowledgeable
about KitchenAid and Maytag refrigerators.
Service update information is designed for the experienced service specialist. It keeps
you advised of the most recent improvements and product changes, and allows you to
service these products more efciently.
WHIRLPOOL CORPORATION assumes no responsibility for any repairs made on
our products by anyone other than authorized In-Home Service Professionals.
®Registered trademark/™ Trademarks of Whirlpool, U.S.A., KitchenAid, U.S.A., Jenn-Air, U.S.A.,
*Always refer to Service Sheet and Use and Care Manual for information specic to the refrigerator you are servicing.
44 1/2”
lbs.
1
Flush Dispenser with Stealth Software
Flush Dispenser (AKA Victoria) with Stealth Software.
User Interface Blue and Amber
Although the Maytag icons are slightly different and the LED color is amber the
controls function the same.
*Always refer to Service Sheet and Use and Care Manual for information specic to the refrigerator you are servicing.
2
Attaching or Removing Handles
KitchenAid handles are held onto mounting studs with Allen screws.
Maytag handles snap off by lifting handle. The mounting studs screw into door skin.
Maytag Handle Removal: Grasp handle with two hands and lift/jerk up.
*Always refer to Service Sheet and Use and Care Manual for information specic to the refrigerator you are servicing.
3
Removing Freezer Door
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Failure to do so can result in death or
electrical shock.
Replace all parts and panels before operating.
1. Unplug refrigerator or disconnect from power.”
2. Disconnect wiring harnesses and water line.
*Always refer to Service Sheet and Use and Care Manual for information specic to the refrigerator you are servicing.
4
Removing Freezer Door (continued)
3. Remove screw and mounting
bracket.
4. Disconnect water tube. 6. Straighten and lay out the har-
5. Disconnect harnesses.
nesses to pull through the hinge.
7. Lift off the freezer door while guiding the water tube and wire harness through
the hinge.
NOTE: Only the harness that is mated with the water tube is routed through the
bottom door hinge.
*Always refer to Service Sheet and Use and Care Manual for information specic to the refrigerator you are servicing.
5
Connecting Water Line
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Failure to do so can result in death or
electrical shock.
Replace all parts and panels before operating.
1. Unplug refrigerator or discon-
nect power.
2. Remove and discard the cap
from the gray water tube.
3. Using a compression nut and
sleeve, attach the copper tube
to the water inlet.
4. Once secured, tighten the compression nut. Do not over
tighten.
5. Check the connection by pull
ing on the copper tubing. Turn
on water supply to refrigerator.
Check for leaks. Tighten any
nuts or connections that leak.
*Always refer to Service Sheet and Use and Care Manual for information specic to the refrigerator you are servicing.
6
Machine Compartment
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Failure to do so can result in death or
electrical shock.
Replace all parts and panels before operating.
1. Unplug refrigerator or disconnect power.
Component and refrigeration tubing identication.
2. Plug on start module.
*Always refer to Service Sheet and Use and Care Manual for information specic to the refrigerator you are servicing.
7
Freezer Compartment -FC
Accelerator has a new small cube icemaker and a special water valve with a 65cc
ow rate.
New Ice Bin Release
The ice bin incorporates a new release. The new design includes a double
latch system for a better engagement.
*Always refer to Service Sheet and Use and Care Manual for information specic to the refrigerator you are servicing.
8
Auger Motor Coupling
Auger motor coupling lifts off motor.
*Always refer to Service Sheet and Use and Care Manual for information specic to the refrigerator you are servicing.
9
Removing Auger Motor
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Failure to do so can result in death or
electrical shock.
Replace all parts and panels before operating.
1. Unplug refrigerator or disconnect power.
2.
3.
Harness is only long enough to allow the motor to be lifted high enough to disconnect.
When installing make sure the harness connection is tight.
*Always refer to Service Sheet and Use and Care Manual for information specic to the refrigerator you are servicing.
10
Loading...
+ 28 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.