Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
You can be killed or seriously injured if you don't immediately
DANGER
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
WARNING: If the information in this manual is not followed exactly, a fire or explosion
may result causing property damage, personal injury or death.
follow instructions.
can be killed or seriously injured if you don't
You
instructions.
follow
– Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
– WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
•
Do not touch any electrical switch.
•
Do not use any phone in your building.
•
Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
•
instructions.
If you cannot reach your gas supplier, call the fire department.
•
– Installation and service must be performed by a qualified installer, service agency or
the gas supplier.
The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish a list of substances
known to the State of California to cause cancer, birth defects, or other reproductive harm, and requires businesses to warn of
potential exposure to such substances.
WARNING: This product contains a chemical known to the State of California to cause cancer, birth defects, or other
reproductive harm.
This appliance can cause low-level exposure to some of the substances listed, including benzene, formaldehyde, carbon
monoxide, toluene, and soot.
3
The Anti-TipBracket
The range will not tip during normal use. However, the range can tip if you apply too much force or weight to the open door without
having the anti-tip bracket fastened down properly.
WARNING
Tip Over Hazard
A child or adult can tip the range and be killed.
Connect anti-tip bracket to rear range foot.
Reconnect the anti-tip bracket, if the range is moved.
See the installation instructions for details.
Failure to follow these instructions can result in death or serious burns to children and adults.
Anti-Tip Bracket
Range Foot
Making sure the anti-tip bracket is installed:
• Slide range forward.
• Look for the anti-tip bracket securely attached to floor.
• Slide range back so rear range foot is under anti-tip bracket.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electrical shock,
injury to persons, or damage when using the range, follow
basic precautions, including the following:
■ WARNING: TO REDUCE THE RISK OF TIPPING OF
THE RANGE, THE RANGE MUST BE SECURED BY
PROPERLY INSTALLED ANTI-TIP DEVICES. TO CHECK
IF THE DEVICES ARE INSTALLED PROPERLY, SLIDE
RANGE FORWARD, LOOK FOR ANTI-TIP BRACKET
SECURELY ATTACHED TO FLOOR, AND SLIDE RANGE
BACK SO REAR RANGE FOOT IS UNDER ANTI-TIP
BRACKET.
■ CAUTION: Do not store items of interest to children in
cabinets above a range or on the backguard of a range –
children climbing on the range to reach items could be
seriously injured.
■ Proper Installation – The range, when installed, must be
electrically grounded in accordance with local codes or, in
the absence of local codes, with the
Code, ANSI/NFPA70
electrically grounded in accordance with Canadian
Electrical Code. Be sure the range is properly installed and
grounded by a qualified technician.
. In Canada, the range must be
National Electrical
■ This range is equipped with a three-prong grounding plug
for your protection against shock hazard and should be
plugged directly into a properly grounded receptacle. Do
not cut or remove the grounding prong from this plug.
■ Disconnect the electrical supply before servicing the
appliance.
■ Never Use the Range for Warming or Heating the Room.
■ Injuries may result from the misuse of appliance doors or
drawers such as stepping, leaning, or sitting on the doors
or drawers.
■ Maintenance – Keep range area clear and free from
combustible materials, gasoline, and other flammable
vapors and liquids.
■ Storage in or on the Range – Flammable materials should
not be stored in an oven or near surface units.
■ Top burner flame size should be adjusted so it does not
extend beyond the edge of the cooking utensil.
For self-cleaning ranges –
■ Before Self-Cleaning the Oven – Remove broiler pan and
other utensils. Wipe off all excessive spillage before
initiating the cleaning cycle.
SAVE THESE INSTRUCTIONS
4
PARTS AND FEATURES
N
O
This manual covers several different models. The range you have purchased may have some or all of the parts and features listed. The
locations and appearances of the features shown here may not match those of your model.
Control Panel
A
Range
A
B
C
D
B
A. Surface burner locator
B. Left rear burner control
C
C. Left front burner controlD. Right front burner control
D
E. Right rear burner control
E
G
H
I
J
K
L
M
E
F
A. Oven vent
B. Surface cooking area
C. Anti-tip bracket
D. Oven door hinge
E. Model and serial number
plate (behind left side of
storage drawer)
F. Storage drawer
(warming drawer on some
models)
G. Electronic oven control
H. Center grate (on some models)
I. Surface burner control
J. Automatic oven light switch
K. Oven rack
L. Gasket
M. Oven door window
N. Self-clean latch
O. Gas regulator
Parts and Features Not Shown
Oven light
Roasting rack
Storage drawer liner (on some
models)
5
COOKTOP USE
D
Cooktop Controls
WARNING
Fire Hazard
Do not let the burner flame extend beyond the edge of
the pan.
Turn off all controls when not cooking.
Failure to follow these instructions can result in death
or fire.
Power failure
In case of prolonged power failure, the surface burners can be lit
manually. Hold a lit match near a burner and turn knob
counterclockwise to LITE. After burner lights, turn knob to
setting. Do not use the grill or griddle during a power failure. The
vent fan will not work.
Sealed Surface Burners
IMPORTANT: Do not obstruct the flow of combustion and
ventilation air around the burner grate edges.
A
B
Electric igniters automatically light the surface burners when
control knobs are turned to LITE.
Before setting a control knob, place filled cookware on the grate.
Do not operate a burner using empty cookware or without having
cookware on the grate.
To S et :
1. Push in and turn knob counterclockwise to LITE.
All 4 surface burners will click. Only the burner with the
control knob turned to LITE will produce a flame.
2. Turn knob anywhere between HI and LO. Use the following
chart as a guide when setting heat levels.
SETTINGRECOMMENDED USE
LITE
HI
MED HI
Medium High
MED
Medium
MED LO
Medium Low
■ Light the burner.
■ Start food cooking.
■ Bring liquid to a boil.
■ Hold a rapid boil.
■ Quickly brown or sear food.
■ To f ry chi ck en .
■ Maintain a slow boil.
■ Fry or sauté foods.
■ Cook soups, sauces and gravies.
■ Stew or steam food.
E
C
A. Burner cap
B. Burner base
C. Alignment pins
D. Igniter
E. Gas tube opening
Burner cap: Always keep the burner cap in place when using a
surface burner. A clean burner cap will help prevent poor ignition
and uneven flames. Always clean the burner cap after a spillover
and routinely remove and clean the caps according to the
“General Cleaning” section.
Gas tube opening: Gas must flow freely throughout the gas tube
opening for the burner to light properly. Keep this area free of soil
and do not allow spills, food, cleaning agents or any other
material to enter the gas tube opening. Protect it from spillovers
by always using a burner cap.
A
B
A. 1-1¹⁄₂" (25-38 mm)
B. Burner ports
LO■ Simmer.
■ Keep food warm.
REMEMBER: When range is in use or (on some models)
during the Self-Cleaning cycle, the entire cooktop area may
become hot.
6
Burner ports: Check burner flames occasionally for proper size
and shape as shown above. A good flame is blue in color, not
yellow. Keep this area free of soil and do not allow spills, food,
cleaning agents or any other material to enter the burner ports.
To C lean :
A
IMPORTANT: Before cleaning, make sure all controls are off and
the oven and cooktop are cool. Do not use oven cleaners, bleach
or rust removers.
1. Remove the burner cap from the burner base and clean
according to “General Cleaning” section.
2. Clean the gas tube opening with a damp cloth.
3. Clean clogged burner ports with a straight pin as shown. Do
not enlarge or distort the port. Do not use a wooden
toothpick. If the burner needs to be adjusted, contact a
trained repair specialist.
4. Replace the burner cap, making sure the alignment pins are
properly aligned with the burner cap.
Cookware
IMPORTANT: Do not leave empty cookware on a hot surface
cooking area, element or surface burner.
Ideal cookware should have a flat bottom, straight sides and a
well-fitting lid, and the material should be of medium-to-heavy
thickness.
Rough finishes may scratch the cooktop. Aluminum and copper
may be used as a core or base in cookware. However, when used
as a base they can leave permanent marks on the cooktop or
grates.
Cookware material is a factor in how quickly and evenly heat is
transferred, which affects cooking results. A nonstick finish has
the same characteristics as its base material. For example,
aluminum cookware with a nonstick finish will take on the
properties of aluminum.
Cookware with nonstick surfaces should not be used under the
broiler.
Use the following chart as a guide for cookware material
characteristics.
COOKWARECHARACTERISTICS
B
A. Incorrect
B. Correct
5. Turn on the burner. If the burner does not light, check cap
alignment. If the burner still does not light, do not service the
sealed burner yourself. Contact a trained repair specialist.
Home Canning
When canning for long periods, alternate the use of surface
cooking areas, elements or surface burners between batches.
This allows time for the most recently used areas to cool.
■ Center the canner on the grate or largest surface cooking
area or element. Canners should not extend more than
1" (2.5 cm) outside the cooking area.
■ Do not place canner on 2 surface cooking areas, elements or
surface burners at the same time.
■ On ceramic glass models, use only flat-bottomed canners.
■ On coil element models, the installation of a Canning Unit Kit
is recommended. If a kit is not installed, the life of the coil
element will be shortened. See “Assistance or Service” for
ordering instructions.
■ For more information, contact your local U.S. Government
Agricultural Department Extension Office. In Canada, contact
Agriculture Canada. Companies that manufacture home
canning products can also offer assistance.
Aluminum
Cast iron
Ceramic or
Ceramic glass
Copper
Earthenware
Porcelain
enamel-onsteel or cast
iron
Stainless steel
■ Heats quickly and evenly.
■ Suitable for all types of cooking.
■ Medium or heavy thickness is best for
most cooking tasks.
■ Heats slowly and evenly.
■ Good for browning and frying.
■ Maintains heat for slow cooking.
■ Follow manufacturer’s instructions.
■ Heats slowly, but unevenly.
■ Ideal results on low to medium heat
settings.
■ Heats very quickly and evenly.
■ Follow manufacturer’s instructions.
■ Use on low heat settings.
■ See stainless steel or cast iron.
■ Heats quickly, but unevenly.
■ A core or base of aluminum or copper
on stainless steel provides even
heating.
7
ELECTRONIC OVEN CONTROLS
Style 1 - Electronic Oven Controls (on some models)
A
KL
J
I
A. Display
B. Timer
C. Clock
D. Oven light pad (on some
models)
E. Cancel
F. Start (control lock)
Style 2 - Electronic Oven Controls (on some models)
A
H
G. Hour/minute (on some
models)
H. Timed cooking
I. Temperature
J. Auto clean
K. Custom broil
L. Bake
BC
B
G
EF
D
C
D
The Start or Start/Enter pad begins any oven function. If the Start
or Start/Enter pad is not pressed within 5 seconds after pressing
a function pad, the “START?” indicator light will flash as a
reminder. On some models, “START?” will appear on the display.
Depending on your model, if Start or Start/Enter is not pressed
within 1 minute or 5 minutes after pressing a function pad, the
oven display will return to the time of day mode and the
programmed function will be canceled.
Start or Start/Enter
EF
Cancel or Off/Cancel
The Cancel or Off/Cancel pad stops any function except the
Clock, Timer and Control Lock.
Clock
This is a 12-hour clock and does not show a.m. and p.m.
To S et :
Before setting, make sure the oven and Timer are off.
1. Press CLOCK.
2. Depending on your model, press the HR or MIN or TIME/
TEMP “up” or “down” arrow pads to set the time of day.
3. Press CLOCK or START.
I
JK
A. Oven display
B. Clock
C. Timer/cancel
D. Start/enter (control lock)
E. Auto clean
F. O f f /c a n ce l
GH
G. Temperature/time
H. Cook time
I. Start time
J. Custom broil
K. Bake
Display
When power is first supplied to the appliance, “PF” or a flashing
time will appear on the display. Press CANCEL or OFF/CANCEL
to clear “PF” or flashing time from the display.
If “PF” or flashing time appears, a power failure has occurred.
Press CANCEL or OFF/CANCEL and reset the clock if needed.
When the oven is not in use, the display shows the time of day.
When performing a timed cook function, the display will show
either hours and minutes, or minutes and seconds.
Tones
Tones are audible signals, indicating the following:
One tone
■ Valid pad press
■ Oven is preheated (long tone)
■ Function has been entered
■ Reminder, repeating each minute after the end-of-cycle tones
Three tones
■ Invalid pad press
Four tones
■ End of cycle
Reminder Tones: Reminder tones may be turned off. On some
models, press and hold STOP TIME for 5 seconds. “rEP OFF” or
“off” will appear in the display. Repeat to turn reminder tones
back on, and “rEP on” or “on” will appear in the display.
All Tones: All of the above tones are preset on, all except the
end-of-cycle tones can be turned off.
To Turn Off/On (on some models): Press and hold START TIME
for 5 seconds. A tone will sound, and “Snd OFF” will appear on
the display. Repeat to turn tones on, and “Snd on” will appear on
the display.
On some models, only the loudness of the tones can be adjusted.
On other models, the tones cannot be adjusted or turned off.
Tone Pitch: The pitch is preset at high, but can be changed to
low. On some models, only the loudness of the tones can be
adjusted. On other models, the tones cannot be adjusted or
turned off.
To Change (on some models): Press and hold BAKE for
5 seconds. A tone will sound, and “Snd LO” will appear on the
display. Repeat to change, and “Snd Hi” will appear on display.
8
Fahrenheit and Celsius
The temperature is preset at Fahrenheit, but can be changed to
Celsius.
To Change: Press and hold CUSTOM BROIL for 5 seconds. A
tone will sound, and “°C” will appear on the display. Repeat to
change back to Fahrenheit. To exit mode, press CANCEL or
OFF/CANCEL.
Timer
The Timer can be set in hours or minutes up to 12 hours and
59 minutes, and counts down the set time. The Timer does not
start or stop the oven.
To S et :
1. Press TIMER SET or TIMER CANCEL*. The timer indicator
light will light up on some models. Depending on your model,
if no action is taken after 1 minute or 5 minutes, the display
will return to the time of day mode.
2. Depending on your model, press the HR or MIN or TIME/
TEMP “up” or “down” arrow pads to set the length of time to
cook.
3. Press TIMER SET or START/ENTER. When the set time ends,
end-of-cycle tones will sound, then, if enabled, reminder
tones will sound every minute on some models.
4. Press TIMER OFF or TIMER CANCEL* anytime to cancel the
Timer and reminder tones.
Remember, do not press the CANCEL or OFF/CANCEL pad
because the oven will turn off.
To display the time of day for 5 seconds when the timer is
counting down, press CLOCK.
Control Lock
The Control Lock shuts down the control panel pads to prevent
unintended use of the oven.
When the control is locked, only the clock, oven light (on some
models) and timer pads will function.
To Lock/Unlock Control: Before locking, make sure the oven
and Timer are off. Press and hold START or START/ENTER for
5 seconds. A single tone will sound, and “Loc” will appear on the
display.
Repeat to unlock. “Loc” will disappear from the display.
OvenTemperature Control
IMPORTANT: Do not use a thermometer to measure oven
temperature because opening the oven door may cause burner
cycling to give incorrect readings.
The oven provides accurate temperatures; however, it may cook
faster or slower than your previous oven, so the temperature
calibration can be adjusted. It can be changed in Fahrenheit or
Celsius.
A minus sign means the oven will be cooler by the displayed
amount. The absence of a sign means the oven will be warmer by
the displayed amount. Use the following chart as a guide.
ADJUSTMENT °F
(ADJUSTMENT °C)
10°F (5°C)...a little more
20°F (10°C)...moderately more
30°F (15°C)...much more
-10°F (-5°C)...a little less
-20°F (-10°C)...moderately less
-30°F (-15°C)...much less
COOKS FOOD
To A dj us t O ve n Te mp er at ure Cali br at io n:
Style 1 - Electronic Oven Controls
1. Press and hold BAKE for 5 seconds until the oven display
shows the current calibration, for example “0°F CAL.”
2. Press the TEMP “up” or “down” arrow pad(s) to increase
or to decrease the temperature in 10°F (5°C) amounts.
The adjustment can be set between 30°F (15°C) and
1. Press and hold BAKE for 5 seconds until the oven display
shows the current calibration, for example “00.”
2. Press the TEMP/TIME “up” or “down” arrow pad to increase
or to decrease the temperature in 10°F amounts. The
adjustment can be set between 30°F and -30°F.
NOTE: All temperature adjustments will be displayed in
Fahrenheit.
3. Press START/ENTER.
OVEN USE
Odors and smoke are normal when the oven is used the first few
times, or when it is heavily soiled.
IMPORTANT: The health of some birds is extremely sensitive to
the fumes given off. Exposure to the fumes may result in death to
certain birds. Always move birds to another closed and well
ventilated room.
Aluminum Foil
IMPORTANT: Do not line the oven bottom with any type of foil,
liners or cookware because permanent damage will occur to the
oven bottom finish.
■ On those models with bottom vents, do not block or cover
the oven bottom vents.
■ Do not cover entire rack with foil because air must be able to
move freely for best cooking results.
■ To catch spills, place foil on rack below dish. Make sure foil is
at least 1" (2.5 cm) larger than the dish and that it is turned up
at the edges.
9
Positioning Racks andBakeware
IMPORTANT: Do not place food or bakeware directly on the oven
door or bottom. Permanent damage will occur to the porcelain
finish.
5
4
3
2
1
6
RACKS
NOTES:
■ Position racks before turning the oven on.
■ Do not move racks with bakeware on them.
■ Make sure racks are level.
To move a rack, pull it out to the stop position, raise the front
edge, then lift out. Use the following illustration and chart as a
guide.
FOODRACK POSITION
Do not place more than 25 lbs (11.3 kg) on the split-rack.
A
A. Split-rack
B. Removable insert
B
To Use Racks:
1. Place a full rack on position 1 or 2, and the split-rack on
position 3 or 4.
2. Place large items on the right side of the full rack.
3. Place deeper, covered dishes on the left side of the full rack.
4. Place shallow dishes on the split-rack.
5. When finished cooking, slowly remove items.
A
Frozen pies, large roasts, turkeys,
1 or 2
angel food cakes
Bundt cakes, most quick breads, yeast
2
breads, casseroles, meats
Cookies, biscuits, muffins, cakes,
2 or 3
nonfrozen pies
Extra-large items6
BAKEWARE
To cook food evenly, hot air must be able to circulate. Allow
2" (5 cm) of space around bakeware and oven walls. Use the
following chart as a guide.
NUMBER OF
POSITION ON RACK
PAN(S)
1Center of rack.
2Side by side or slightly staggered.
3 or 4Opposite corners on each rack. Make sure
that no bakeware piece is directly over
another.
Split Oven Rack
(on somemodels)
Split-Rack with Removable Insert
The split-rack with removable insert is a space maximizer. When
the two are attached, they make a full rack. The insert can also be
removed to provide room for large items such as a turkey and
casseroles.
The insert can also be used on the counter for a cooling rack.
B
A. Rear rack section
B. Front rack section
Bakeware
The bakeware material affects cooking results. Follow
manufacturer’s recommendations and use the bakeware size
recommended in the recipe. Use the following chart as a guide.
BAKEWARE/
RESULTS
Light colored
aluminum
■ Light golden
crusts
■ Even browning
Dark aluminum and
other bakeware with
dark, dull and/or
nonstick finish
■ Brown, crisp
crusts
Insulated cookie
sheets or baking
pans
■ Little or no
bottom browning
RECOMMENDATIONS
■ Use temperature and time
recommended in recipe.
■ May need to reduce baking
temperatures 25°F (15°C).
■ Use suggested baking time.
■ For pies, breads and casseroles,
use temperature recommended in
recipe.
■ Place rack in center of oven.
■ Place in the bottom third of oven.
■ May need to increase baking time.
10
BAKEWARE/
RECOMMENDATIONS
RESULTS
Stainless steel
■ Light, golden
■ May need to increase baking time.
crusts
■ Uneven browning
Stoneware
■ Crisp crusts
Ovenproof
glassware, ceramic
■ Follow manufacturer’s
instructions.
■ May need to reduce baking
temperatures 25°F (15°C).
glass or ceramic
■ Brown, crisp
crusts
Meat Thermometer
On models without a temperature probe, always rely on a meat
thermometer to determine doneness of meat and poultry. The
internal temperature, not appearance, is what counts. A meat
thermometer is not supplied with this appliance.
■ Insert the thermometer into the center of the thickest portion
of the meat or inner thigh or breast of poultry. The tip of the
thermometer should not touch fat, bone or gristle.
■ After reading the thermometer once, push it into the meat
½" (1.25 cm) more and read again. If the temperature drops,
cook the meat or poultry longer.
■ Check all meat in 2 or 3 places.
OvenVent
A
A. Oven vent
The oven vent releases hot air and moisture from the oven, and
should not be blocked or covered. Blocking or covering the oven
vent will cause poor air circulation, affecting cooking and
cleaning results. Do not set plastics, paper or other items that
could melt or burn near the oven vent.
Baking and Roasting
Before baking and roasting, position racks according to the
“Positioning Racks and Bakeware” section. When roasting, it is
not necessary to wait for the oven preheat conditioning time to
end before putting food in unless recommended in the recipe.
To Bake or Roast:
1. Press BAKE.
2. Press TEMP or TEMP/TIME “up” or “down” arrow pad to set
a temperature other than 350°F (175°C) in 5°F (5°C) amounts.
The bake range can be set between 170°F and 500°F (75°C
and 260°C).
When the oven temperature is greater than 170°F (77°C), no
preheat conditioning time will be shown in the display. The
preheat conditioning time will not change if the temperature is
reset before the countdown time ends.
3. Press START or START/ENTER. The temperature can be
changed after this step. The start pad does not need to be
pressed again.
If baking and roasting while the minute timer is counting
down, the set temperature can be seen for 5 seconds by
pressing BAKE.
4. Press CANCEL or OFF/CANCEL when finished.
Preheating
After the start pad is pressed, the oven will enter a timed preheat
conditioning. “PrE” (on some models) and the countdown time
will appear on the display. When the preheat conditioning time
ends, a tone will sound and the selected temperature will appear
on the display.
Preheat temperatures are affected by varying factors such as
room temperature and peak energy usage times. It is normal for
the temperature showing on the display and the actual oven
temperature to differ due to the cycling of the elements.
Waiting an additional 10 minutes, after the preheat conditioning
time ends, to put food in the oven is suggested when baking
foods with leavening ingredients, such as yeast, baking powder,
baking soda and eggs.
Broiling and Custom Broiling
Broiling uses direct radiant heat to cook food. Changing the
temperature when Custom Broiling allows more precise control
when cooking. The lower the temperature, the slower the
cooking. Thicker cuts and unevenly shaped pieces of meat, fish
and poultry may cook better at lower broiling temperatures.
If your model does not have a broiler pan, one may be ordered.
Ask for Part Number 4396923.
■ For best results, use a broiler pan and grid (provided on some
models). It is designed to drain juices and help prevent
spatter and smoke.
■ For proper draining, do not cover the grid with foil. The
bottom of the pan may be lined with aluminum foil for easier
cleaning.
■ Trim excess fat to reduce spattering. Slit the remaining fat on
the edges to prevent curling.
■ Pull out oven rack to stop position before turning or removing
food. Use tongs to turn food to avoid the loss of juices. Very
thin cuts of fish, poultry or meat may not need to be turned.
■ After broiling, remove the pan from the oven when removing
the food. Drippings will bake on the pan if left in the heated
oven, making cleaning more difficult.
Before broiling, position rack according to the Broiling Chart. It is
not necessary to preheat the oven before putting food in unless
recommended in the recipe. Position food on grid in the broiler
pan, then place it in the center of the oven rack. Close the door.
To B roi l:
1. Press CUSTOM BROIL.
2. Press START or START/ENTER.
3. Press CANCEL or OFF/CANCEL when finished.
To Custom Broil:
1. Press CUSTOM BROIL.
2. Press TEMP or TEMP/TIME “up” or “down” arrow pad to
change the temperature in 5°F (5°C) amounts. The broil range
can be set between 300°F (150°C) and HI (525°F [275°C]).
3. Press START or START/ENTER.
If broiling while the timer is counting down, the set broiling
temperature can be seen for 5 seconds by pressing CUSTOM
BROIL.
4. Press CANCEL or OFF/CANCEL when finished.
11
Loading...
+ 25 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.