WHIRLPOOL HSCX 80533 Daily Reference Guide

DAILY REFERENCE

WWW

GUIDE

THANK YOU FOR PURCHASING A WHIRLPOOL PRODUCT

To receive more comprehensive help and support, please register your product at www. whirlpool. eu / register

Before using the appliance carefully read the Health and Safety guide.

PRODUCT DESCRIPTION

APPLIANCE

You can download the Safety Instructions and the Use and Care Guide by visiting our website docs. whirlpool. eu and following the instructions on the back of this booklet.

1. Worktop

2. Control panel

3. Water tank

4. Door

5. Door handle

6. Door filter (behind

door)

7. Bottom filter (behind flap)

8. Adjustable feet (4)

CONTROL PANEL

13.

12.

1. On/Off button (Reset if

long pressed)

2. Programme button

3. Settings button

4. Key lock

5. Steam option

6. Knob (Turn to select /

Press to confirm)

7. Finish in

8. Drying time

9. Dryness level

10. Options button

11. Start / Pause button

12. Display

13. Programmes area

1. 7.2.

6. 8.4. 10.3. 9.5. 11.

FIRST TIME USE

BEFORE USING THE DRYER

CHECK DRAIN HOSE AND WATER TANK

Make sure that the water tank is correctly inserted.

When switching on the dryer for the rst time, you will be asked to

• Set the desired language

• Adapt the value for your local water conductivity

• Set the dryer to recall the last used programme setting or not when switching it on.

Refer to HINTS AND TIPS and OPTIONS, FUNCTIONS AND INDICATORS / Settings.

Make sure that the drain hose on the back of the dryer is xed correctly, either to the dryer’s water tank, or to your domestic sewage system (see Installation guide).

The dryer should be installed in an ambient room temperature of between 20 to 23°C for optimum performance. But will function if the room is between 14 and 30°C.

DAILY USE

Make sure that no lighters or

WARNING

1. LOAD LAUNDRY

• Prepare your laundry according to the recommendations in section “HINTS AND TIPS”. Make sure that pockets are empty.

• Open the door and load the laundry. Observe the maximum load sizes given in the PROGRAMME CHART.

matches remain in the laundry

See Use and Care Guide for more details on functions / see last page for information on how to obtain the Use and Care Guide

Make sure that the laundry is not soaked with flammable liquids.

2. CLOSE THE DOOR

• Make sure that no laundry gets stuck between door glass and door lter.

• Close the door so that you can hear it click shut.

3. SWITCH ON DRYER

• Press the On/O button until the programme button lights up. An animation occurs, and there is a sound. Afterwards the dryer is ready to be operated.

4. SET THE DESIRED PROGRAMME

GUIDED MODE  the button light will guide you through setting

your programme in the following order: selection of programme / drying time (ONLY if Drying time or Airing programme is selected) / dryness level (only if selectable/adjustable) / options. As soon as you conrm a selection by pressing the knob, the button light will jump to the next step.

• Select programme:

Make sure that the programme button lights up.

Turn the knob to select the desired programme. The indicator next to the selected programme lights up. Conrm by pressing the knob.

Programme position oers a choice of special programmes, which you can select by turning the knob; afterwards press the knob to conrm the selected programme. Find more information regarding programmes in the Programme Chart.

• Select Drying time, if needed

ONLY if you have selected programme Drying time or Airing, you can set the desired drying / airing time from a minimum

of 10 minutes to maximum 180 minutes (three hours). Make sure that the Drying time button lights up. Turn the knob to select the desired drying / airing time. Conrm it by pressing the knob.

INDIVIDUAL MODE

After you have switched on the dryer, you are not forced to follow the GUIDED MODE. It is up to you which order you choose to set your programme. To do a setting, rst press the relevant button, then turn the knob to select, and nally press the knob to conrm. The variety of options and dryness levels depends on the programme selected. Therefore it is recommended to start your setting with selecting the programme.

5. START PROGRAMME

• Press and hold Start/Pause until the button lights up solidly; the drying process starts.

• The duration can be recalculated and adapted in the course of the programme. During such phases, an animation occurs on the

display.

6. CHANGE THE SETTINGS OF A RUNNING PROGRAMME, IF

NEEDED

You can still change some settings after a programme was started: Adjust drying time (only if programme Drying time or Airing is selected): Adjust or cancel “Finish in”, if a delay was selected and started Add or cancel an option, provided the progress of the programme still allows it.

• Press the relevant button. The selected setting will blink for a few seconds.

• While blinking, you can adjust the setting by turning the knob. If the value or setting stopped blinking, press the button again.

• Press the knob to conrm the modication. If you do not conrm, the modication will be conrmed automatically – the modied setting will stop blinking.

The programme will continue automatically. To change the settings of a running programme or delay, you can also:

• Press Start/Pause to put the running programme on pause

• Change your settings

• Press Start/Pause again to continue the programme.

• Set dryness level, if needed

If you want to change the dryness level, make sure that the Dryness level button lights up. Turn the knob to select the desired dryness level, then press the knob to conrm.

• Select options, if needed

• If you want to select additional options, make sure that the options button lights up. The options which are selectable for your programme are indicated by lighting arrows

Turn the knob to select the desired options. The symbol of the selected option blinks. To conrm it, press the knob. Some options / functions can be selected by directly pressing the button:

Refer to section OPTIONS, FUNCTIONS AND INDICATORS for more information.

7. RESET A RUNNING PROGRAMME, IF NEEDED

• Press and hold the On/O button until the display indicates that the programme is cancelled.

8. SWITCH OFF THE DRYER AFTER PROGRAMME END

• The display indicates that the cycle has nished. Press On/ O to switch o the dryer. Open the door and take out your laundry.

• The dryer will switch o automatically in about a quarter of an hour after programme end, to save energy.

• If not switched o right after programme end, the dryer will tumble the laundry for about 10 minutes, to prevent creasing. The display shows an animation.

9. EMPTY WATER TANK / CLEAN DOOR FILTER / CLEAN

BO T TOM F ILTER

• Refer to section CARE AND MAINTENANCE.

+ 5 hidden pages