Whirlpool FRONT-LOADING GAS DRYER User Manual

FRONT-LOADING GAS DRYER

Use &Care Guide

For questions about features, operation/performance, parts, accessories or service, call: 1-800-422-1230

In Canada, call : 1-800-807-6777 or visit our website at...

www.kitchenaid.com or www.KitchenAid.ca

SECADORA A GAS DE CARGA FRONTAL

Manual de Usoy Cuidado

Si tiene preguntas respecto a las características, funcionamiento/rendimiento, partes, accesorios o servicio técnico, llame al: 1-800-422-1230

Para la instalación y el servicio llame al: 1-800-807-6777 o visite nuestro sitio web en... www.kitchenaid.com

SÉCHEUSE À GAZ À CHARGEMENT À L'AVANT

Guide d’utilisation etd’entretien

Au Canada, composez le 1-800-807-6777

ou visitez notre site web à... www.KitchenAid.ca

Table of Contents/Índice/Table des matières..................................................................2

8562593B

TABLE OF CONTENTS

DRYER SAFETY..............................................................................3

INSTALLATION INSTRUCTIONS..................................................4

Tools and Parts ............................................................................4

Options.........................................................................................5

Location Requirements ...............................................................5

Electrical Requirements ...............................................................7

Gas Supply Requirements...........................................................7

Venting Requirements..................................................................9

Plan Vent System.......................................................................10

Install Vent System.....................................................................11

Install Leveling Legs...................................................................11

Make Gas Connection ...............................................................12

Connect Vent..............................................................................12

Level Dryer .................................................................................12

Reverse Door Swing ..................................................................12

Complete Installation .................................................................14

DRYER USE ..................................................................................15

Starting Your Dryer.....................................................................15

ÍNDICE

SEGURIDAD DE LA SECADORA................................................24

INSTRUCCIONES DE INSTALACIÓN.........................................26

Herramientas y piezas................................................................26

Opciones ....................................................................................26

Requisitos de ubicación.............................................................26

Requisitos eléctricos..................................................................29

Requisitos del suministro de gas...............................................29

Requisitos de ventilación...........................................................31

Planificación del sistema de ventilación....................................32

Instalación del sistema de ventilación.......................................33

Instalación de las patas niveladoras..........................................33

Conexión del suministro de gas ................................................34

Conexión del ducto de escape..................................................34

Nivelación de la secadora..........................................................35

Cómo invertir el cierre de la puerta............................................35

Complete la instalación..............................................................36

USO DE LA SECADORA..............................................................37

Puesta en marcha de la secadora .............................................37

Stopping Your Dryer...................................................................16

Pausing or Restarting.................................................................16

Control Locked...........................................................................16

Drying and Cycle Tips ................................................................16

Status Lights...............................................................................17

Cycles.........................................................................................17

Additional Features ....................................................................18

Drying Rack ................................................................................19

DRYER CARE...............................................................................19

Cleaning the Dryer Location.......................................................19

Cleaning the Lint Screen............................................................19

Cleaning the Dryer Interior .........................................................20

Removing Accumulated Lint......................................................20

Vacation and Moving Care.........................................................20

Changing the Drum Light ...........................................................20

TROUBLESHOOTING ..................................................................21

ASSISTANCE OR SERVICE.........................................................22

WARRANTY ..................................................................................23

Detención de la marcha de la secadora ....................................38

Pausa o reanudación de la marcha ...........................................38

Control bloqueado .....................................................................38

Sugerencias de ciclos y secado ................................................38

Luces de estado.........................................................................39

Ciclos..........................................................................................39

Características adicionales ........................................................40

Estante de secado......................................................................41

CUIDADO DE LA SECADORA....................................................42

Limpieza del lugar donde está la secadora...............................42

Limpieza del filtro de pelusa ......................................................42

Limpieza del interior de la secadora ..........................................43

Eliminación de pelusa acumulada .............................................43

Cuidado para las vacaciones y la mudanza..............................43

Cambio de la luz del tambor......................................................43

SOLUCIÓN DE PROBLEMAS......................................................43

AYUDA O SERVICIO TÉCNICO...................................................45

GARANTÍA.....................................................................................46

TABLE DES MATIÈRES

SÉCURITÉ DE LA SÉCHEUSE....................................................47

INSTRUCTIONS D’INSTALLATION ............................................49

Outillage et pièces......................................................................49

Options.......................................................................................49

Exigences d’emplacement.........................................................49

Spécifications électriques..........................................................52

Spécifications de l'alimentation en gaz .....................................52

Exigences concernant l'évacuation...........................................54

Planification du système d’évacuation......................................55

Installation du système d’évacuation ........................................56

Installation des pieds de nivellement.........................................56

Raccordement au gaz................................................................57

Raccordement du conduit d’évacuation ...................................57

Mise à niveau de la sécheuse....................................................58

Inversion de l'ouverture de la porte ...........................................58

Achever l’installation ..................................................................59

UTILISATION DE LA SÉCHEUSE................................................60

Mise en marche de la sécheuse ................................................60

Arrêt de la sécheuse...................................................................61

Pause ou remise en marche.......................................................61

Verrouillage des commandes.....................................................61

Conseils pour le séchage et les programmes ...........................61

Témoins lumineux ......................................................................62

Programmes...............................................................................63

Caractéristiques supplémentaires .............................................64

Grille de séchage........................................................................65

ENTRETIEN DE LA SÉCHEUSE.................................................66

Nettoyage de l'emplacement de la sécheuse ...........................66

Nettoyage du filtre à charpie......................................................66

Nettoyage de l’intérieur de la sécheuse.....................................66

Retrait de la charpie accumulée ................................................67

Précautions à prendre pour les vacances et avant un

déménagement ..........................................................................67

Changement de l’ampoule d’éclairage du tambour..................67

DÉPANNAGE.................................................................................68

ASSISTANCE OU SERVICE.........................................................70

GARANTIE.....................................................................................71

DRYER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

You can be killed or seriously injured if you don't immediately

DANGER

WARNING

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

WARNING: For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, or to prevent property damage, personal injury, or death.

follow instructions.

can be killed or seriously injured if you don't

You instructions.

– Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

– WHAT TO DO IF YOU SMELL GAS:

Do not try to light any appliance.

•

Do not touch any electrical switch; do not use any phone in your building.

•

Clear the room, building, or area of all occupants.

•

Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

•

instructions. If you cannot reach your gas supplier, call the fire department.

•

– Installation and service must be performed by a qualified installer, service agency, or

the gas supplier.

In the State of Massachusetts, the following installation instructions apply:

■ Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by

the State of Massachusetts.

■ If using a ball valve, it shall be a T-handle type.

■ A flexible gas connector, when used, must not exceed 3 feet.

IMPORTANT SAFETY INSTRUCTIONS

WARNING:

including the following:

■

Read all instructions before using the dryer.

■

Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch fire.

■

Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, drycleaning solvents, or other flammable or explosive substances as they give off vapors that could ignite or explode.

■

Do not allow children to play on or in the dryer. Close supervision of children is necessary when the dryer is used near children.

■

Before the dryer is removed from service or discarded, remove the door to the drying compartment.

■

Do not reach into the dryer if the drum is moving.

■

Do not install or store the dryer where it will be exposed to the weather.

■

Do not tamper with controls.

To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions,

■

Do not repair or replace any part of the dryer or attempt any servicing unless specifically recommended in this Use and Care Guide or in published user-repair instructions that you understand and have the skills to carry out.

■

Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product.

■

Do not use heat to dry articles containing foam rubber or similarly textured rubber-like materials.

■

Clean lint screen before or after each load.

■

Keep area around the exhaust opening and adjacent surrounding areas free from the accumulation of lint, dust, and dirt.

■

The interior of the dryer and exhaust vent should be cleaned periodically by qualified service personnel.

■

See installation instructions for grounding requirements.

SAVE THESE INSTRUCTIONS

IMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54 or the Canadian Natural Gas and Propane Installation Code, CSA B149.1.

The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1.

INSTALLATION INSTRUCTIONS

Tools andParts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

■ 8" or 10" pipe wrench

■ 8" or 10" adjustable

wrench (for gas connections)

■ Flat-blade screwdriver

■ Adjustable wrench that

opens to 1" (2.5 cm) or hex-head socket wrench (for adjusting dryer feet)

■ ¹⁄₄" nut driver or socket

wrench (recommended)

Parts supplied

Remove parts packages from dryer drum. Check that all parts are included.

■ Level

■ Knife

■ Vent clamps

■ Pipe-joint compound

resistant to LP gas

■ Caulking gun and

compound (for installing new exhaust vent)

■ Pliers

■ Tape measure

Parts needed

Check local codes and with gas supplier. Check existing gas supply, electrical supply and venting. Read “Electrical Requirements,” “Gas Supply Requirements” and “Venting Requirements” before purchasing parts.

■ For close-clearance installations between 31.5" (80.01 cm)

and 37" (93.98 cm), see “Plan Vent System” section for venting requirements.

37" (93.98 cm)

Mobile home installations require special parts (listed following) that may be ordered by calling the dealer from whom you purchased your dryer. For further information, please refer to the “Assistance or Service” section of this manual.

■ Mobile Home Installation Kit. Ask for Part Number 346764.

■ Metal exhaust system hardware.

4 Leveling legs

NOTE: Do not use leveling legs if installing the dryer on a pedestal.

Options

Pedestal

Are you placing the dryer on a pedestal? You may purchase a pedestal separately for this dryer. This pedestal will add about 13" (33 cm) to the height of your unit for a total height of approximately 51" (130 cm).

For a garage installation, you will need to place the pedestal at least 6" (15.2 cm) above the floor.

Optional pedestal

To order, call the dealer from whom you purchased your dryer or refer to the “Assistance or Service” section of this manual. Ask for Part Number LAB2700PMT (Meteorite) or LAB2700MQ0 (White).

Stack Kit

Are you planning to stack your washer and dryer? To do so, you will need to purchase a Stack Kit.

To order, call the dealer from whom you purchased your dryer or refer to the “Assistance or Service” section of this manual. Ask for Part Number 8541503.

Location Requirements

■ A sturdy floor to support the total dryer weight of 200 lbs

(90.7 kg). The combined weight of a companion appliance should also be considered.

■ A level floor with a maximum slope of 1" (2.5 cm) under entire

dryer. If slope is greater than 1" (2.5 cm), install Extended Dryer Feet Kit, Part Number 279810. Clothes may not tumble properly, and automatic sensor cycles may not operate correctly if dryer is not level.

■ For a garage installation, you will need to place the dryer at

least 18" (46 cm) above the floor. If using a pedestal, you will need to place the pedestal at least 6" (22.9 cm) above the floor.

Do not operate your dryer at temperatures below 45ºF (7ºC). At lower temperatures, the dryer might not shut off at the end of an automatic cycle. This can result in longer drying times.

The dryer must not be installed or stored in an area where it will be exposed to water and/or weather.

Check code requirements. Some codes limit, or do not permit, installation of the dryer in garages, closets, mobile homes or sleeping quarters. Contact your local building inspector.

NOTE: No other fuel-burning appliance can be installed in the same closet as a dryer.

Installation clearances

■ The location must be large enough to allow the dryer door to

open fully.

■ Additional spacing should be considered for ease of

installation and servicing.

■ Additional clearances might be required for wall, door and

floor moldings.

■ Additional spacing of 1" (2.5 cm) on all sides of the dryer is

recommended to reduce noise transfer.

■ Companion appliance spacing should also be considered.

Dryer Dimensions

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from dryer.

Place dryer at least 18 inches (46 cm) above the floor for a garage installation.

Failure to do so can result in death, explosion, or fire.

You will need

■ A location that allows for proper exhaust installation. A gas

dryer must be exhausted to the outdoors. See “Venting Requirements.”

■ If you are using a power supply cord, a grounded electrical

outlet located within 2 ft (61 cm) of either side of the dryer. See “Electrical Requirements.”

51½"

(130.81 cm)

38"

(96.52 cm

)

*31½" (80 cm)

27"

(68.6 cm)

*Most installations require a minimum 5½" (14 cm) clearance

behind the dryer for the exhaust vent with elbow. See “Venting Requirements.”

Minimum installation spacing for custom undercounter

)

installation

The dimensions shown are for the minimum spacing allowed.

Custom undercounter installation - Dryer only

(0 cm)

38" min. (96.52 cm)

Minimum installation spacing for cabinet installation

■ The dimensions shown are for the minimum spacing allowed.

■ For cabinet installation, with a door, minimum ventilation

openings in the top of the cabinet are required.

7" (17.8 cm)

0"* (0 cm)

27" (68.6 cm)

0"* (0 cm)

*Additional spacing recommended

Minimum installation spacing for recessed or closet installation, with or without a pedestal

■ The dimensions shown are for the minimum spacing allowed.

■ For closet installation, with a door, minimum ventilation

openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable.

Closet installation - Dryer only

14" max. (35.6 cm)

18" min. (45.72 cm)

(7.6 cm)

(2.5 cm)

31½"

(80 cm)

14" max. (35.6 cm)

18" min. (45.72 cm)

0"*

(0 cm)

48 in.

(310 cm2)

24 in.

(155 cm2)

A. Side view - closet or confined area B. Closet door with vents

*Side or bottom venting - additional spacing recommended

Recessed or closet installation - Dryer on pedestal

0"**

(0 cm)

31¹₂"

(80.0 cm)

(2.5 cm)

27"

0"* 0"*

(68.6 cm)

(0 cm)

*Additional spacing recommended

**Side or bottom venting - additional spacing recommended

Recommended installation spacing for recessed or closet installation, with stacked washer and dryer

The dimensions shown are for the recommended spacing.

48 in.2 *

(310 cm2)

3" (7.6 cm)

24 in.

(155 cm2)

*Min. top and bottom air openings for closet door

6" (15.2 cm)

1" (2.5 cm)

9" (22.9 cm

0"*

(0 cm)

27"

(68.6 cm)

0"*

(0 cm)

(2.5 cm)

31½"

(80 cm)

0"**

(0 cm)

A. Recessed area B. Side view - closet or confined area

*Additional spacing recommended

**Side or bottom venting - additional spacing recommended

76"

(193 cm)

5½"**

(14 cm)

†

1"**

(2.5 cm)

27"

(68.6 cm)

†

1"**

(2.5 cm)

**External exhaust elbow requires additional spacing.

**†Wall, door and floor molding may require additional spacing.

Mobile home - Additional installation requirements

This dryer is suitable for mobile home installations. The installation must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280) or Standard CAN/CSA-Z240 MH.

Mobile home installations require:

■ Metal exhaust system hardware, which is available for

purchase from your dealer.

■ Mobile Home Installation Kit Part Number 346764. See “Tools

and Parts” section for ordering information.

■ Special provisions must be made in mobile homes to

introduce outside air into the dryer. The opening (such as a nearby window) should be at least twice as large as the dryer exhaust opening.

Electrical Requirements

WARNING

Gas Supply Requirements

WARNING

Explosion Hazard Use a new CSA International approved gas supply line. Install a shut-off valve. Securely tighten all gas connections. If connected to LP, have a qualified person make sure

gas pressure does not exceed 13" (33 cm) water column.

Examples of a qualified person include: licensed heating personnel,

authorized gas company personnel, and authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

■ 120 Volt, 60 Hz., AC only, 15- or 20-amp fused electrical

supply is required. A time-delay fuse or circuit breaker is recommended. It is also recommended that a separate circuit serving only this dryer be provided.

GROUNDING INSTRUCTIONS

■

For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This dryer is equipped with a cord having an equipmentgrounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Gas Type

Natural gas:

This dryer is equipped for use with Natural gas. It is designcertified by CSA International for LP (propane or butane) gases with appropriate conversion.

■ Your dryer must have the correct burner for the type of gas in

your home. Burner information is located on the rating plate in the door well of your dryer. If this information does not agree with the type of gas available, contact your dealer or call the phone numbers referenced in the “Assistance or Service” section of this manual.

LP gas conversion: Conversion must be made by a qualified technician.

No attempt shall be made to convert the appliance from the gas specified on the model/serial rating plate for use with a different gas without consulting your gas company.

Gas supply line

■ ½" IPS pipe is recommended.

■ ³⁄₈" approved tubing is acceptable for lengths under

20 ft (6.1 m) if local codes and gas supplier permit.

■ Must include ¹⁄₈" NPT minimum plugged tapping accessible

for test gauge connection, immediately upstream of the gas connection to the dryer (see following illustration).

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative or personnel if you are in doubt as to whether the dryer is properly grounded. Do not modify the plug provided with the dryer: if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

■ Must include a shutoff valve:

In the U.S.A.:

An individual manual shutoff valve must be installed within six (6) feet (1.8 m) of the dryer in accordance with the National Fuel Gas Code, ANSI Z223.1.

In Canada:

An individual manual shutoff valve must be installed in accordance with the B149.1, Natural Gas and Propane Installation Code. It is recommended that an individual manual shutoff valve be installed within six (6) feet (1.8 m) of the dryer.

The location should be easy to reach for opening and closing.

A. ³⁄₈" flexible gas connector B. ³⁄₈" pipe to flare adapter fitting

NPT minimum plugged tapping

C. ¹⁄₈" D. ½" NPT gas supply line

E. Gas shutoff valve

Gas supply connection requirements

■ For close clearances, a ³⁄₈" to ³⁄₈" elbow is recommended to

avoid kinking of the gas line.

■ Use only pipe-joint compound. Do not use TEFLON

®†

tape.

There are many methods by which your gas dryer can be connected to the gas supply. Listed here are some guidelines for two different methods of connection.

Option 1 (Recommended method)

Flexible stainless steel gas connector:

■ If local codes permit, use a new flexible stainless steel gas

connector (Design Certified by CSA International) to connect your dryer to the rigid gas supply line. Use an elbow and a ³⁄₈"flare x ³⁄₈" NPT adapter fitting between the stainless steel gas connector and the dryer gas pipe, as needed to avoid kinking.

Option 2 (Alternate method)

Approved aluminum or copper tubing:

■ Lengths under 20 ft (6.1 m) can use ³⁄₈" approved tubing

(if codes and gas supplier permit).

■ If you are using Natural gas, do not use copper tubing.

■ ³⁄₈" flare x ³⁄₈" NPT adapter fitting between dryer pipe and

³⁄₈" approved tubing.

■ Lengths over 20 ft (6.1 m) should use larger tubing and a

different size adapter fitting.

■ If your dryer has been converted to use LP gas, ³⁄₈" LP

compatible copper tubing can be used. If the total length of the supply line is more than 20 ft (6.1 m), use larger tubing.

NOTE: Pipe-joint compounds that resist the action of LP gas must be used. Do not use TEFLON

®†

tape.

Burner input requirements

Elevations up to 10,000 ft (3,048 m):

■ The design of this dryer is certified by CSA International for

use at altitudes up to 10,000 ft (3,048 m) above sea level at the B.T.U. rating indicated on the model/serial number plate. Burner input adjustments are not required when the dryer is operated up to this elevation.

Elevations above 10,000 ft (3,048 m):

■ When installed above 10,000 ft (3,048 m) a 4% reduction of

the burner B.T.U. rating shown on the model/serial number plate is required for each 1,000 ft (305 m) increase in elevation.

Gas supply pressure testing

■ The dryer must be disconnected from the gas supply piping

system during pressure testing at pressures greater than ½ psi.

Dryer gas pipe

■ The gas pipe that comes out through the rear of your dryer

has a ³⁄₈" male pipe thread.

1½" (3.8 cm)

*6¼" (15.9 cm)

A. ½" NPT gas supply line

³⁄₈

" NPT dryer pipe

*NOTE: If the dryer is mounted on a pedestal, the gas pipe height

must be an additional 13" (33 cm) from the floor. For a garage installation, the gas pipe height must be an additional 18" (46 cm) from the floor.

†®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

Venting Requirements

WARNING

Fire Hazard Use a heavy metal vent. Do not use a plastic vent. Do not use a metal foil vent. Failure to follow these instructions can result in death

or fire.

WARNING: To reduce the risk of fire, this dryer MUST BE

EXHAUSTED OUTDOORS. IMPORTANT: Observe all governing codes and ordinances. The dryer exhaust must not be connected into any gas vent,

chimney, wall, ceiling or a concealed space of a building.

If using an existing vent system

■ Remove excess flexible metal vent to avoid sagging and

kinking that may result in reduced airflow and poor performance.

■ Do not install flexible metal vent in enclosed walls, ceilings or

floors.

Elbows

45° elbows provide better airflow than 90° elbows.

Good Better

Clamps

■ Use clamps to seal all joints.

■ Exhaust vent must not be connected or secured with screws

or other fastening devices that extend into the interior of the duct. Do not use duct tape.

■ Clean lint from the entire length of the system and make sure

exhaust hood is not plugged with lint.

■ Replace any plastic or metal foil vent with rigid or flexible

heavy metal vent.

■ Review Vent system chart. Modify existing vent system if

necessary to achieve the best drying performance.

If this is a new vent system

Vent material

■ Use a heavy metal vent. Do not use plastic or metal foil vent.

■ 4" (10.2 cm) heavy metal exhaust vent and clamps must be

used. DURASAFE™ venting products are recommended.

10.2 cm

4" (10.2 cm) heavy metal exhaust vent

DURASAFE™ vent products can be purchased from your dealer or by calling Whirlpool Parts and Accessories. For more information, see the “Assistance or Service” section of this manual.

Rigid metal vent

■ For best drying performance, rigid metal vents are

recommended.

■ Rigid metal vent is recommended to avoid crushing and

kinking.

Flexible metal vent

■ Flexible metal vents are acceptable only if accessible for

cleaning.

■ Flexible metal vent must be fully extended and supported

when the dryer is in its final location.

Clamp

Exhaust

Recommended hood styles are shown here.

(10.2 cm)

4" (10.2 cm)

A. Louvered hood style B. Box hood style

The angled hood style (shown here) is acceptable.

(10.2 cm)

2½"

(6.4 cm)

■ An exhaust hood should cap the vent to keep rodents and

insects from entering the home.

■ Exhaust hood must be at least 12" (30.5 cm) from the ground

or any object that may be in the path of the exhaust (such as flowers, rocks or bushes, snow line, etc.).

■ Do not use an exhaust hood with a magnetic latch.

Improper venting can cause moisture and lint to collect indoors, which may result in:

Moisture damage to woodwork, furniture, paint,

wallpaper, carpets, etc.

Housecleaning problems and health problems.

PlanVentSystem

Choose your exhaust installation type

Recommended exhaust installations

Typical installations vent the dryer from the rear of the dryer. Other installations are possible.

E F G

A. Dryer

B. Elbow C. Wall D. Exhaust hood

E. Clamps F. Rigid metal or flexible metal vent

G. Vent length necessary to connect

elbows

H. Exhaust outlet

Optional exhaust installations

This dryer can be converted to exhaust out the right side, left side or through the bottom. If you prefer, you may contact your local dealer to have the dryer converted.

WARNING

Fire Hazard Cover unused exhaust holes with one of the

following kits: 279818 (white) 280028 (meteorite) Contact your local dealer. Failure to follow these instructions can result in death,

fire, electrical shock, or serious injury.

Alternate installations for close clearances

Venting systems come in many varieties. Select the type best for your installation. Two close-clearance installations are shown. Refer to the manufacturer’s instructions.

A. Over-the-top installation (also available with one

offset elbow)

B. Periscope installation

NOTE: The following kits for close clearance alternate installations are available for purchase. Please see the “Assistance or Service” section of this manual to order.

■ Over-the-Top Installation:

Part Number 4396028

■ Periscope Installation (For use with dryer vent to wall vent

mismatch): Part Number 4396037 - 0" (0 cm) to 18" (45.72 cm)

mismatch Part Number 4396011 - 18" (45.72 cm) to 29" (73.66 cm)

mismatch Part Number 4396014 - 29" (73.66 cm) to 50" (127 cm)

mismatch

Special provisions for mobile home installations

The exhaust vent must be securely fastened to a noncombustible portion of the mobile home structure and must not terminate beneath the mobile home. Terminate the exhaust vent outside.

A. Standard rear offset exhaust installation B. Left or right side exhaust installation C. Bottom exhaust installation

Determine vent path

■ Select the route that will provide the straightest and most

direct path outdoors.

■ Plan the installation to use the fewest number of elbows and

turns.

■ When using elbows or making turns, allow as much room as

possible.

■ Bend vent gradually to avoid kinking.

■ Use the fewest 90° turns possible.

Determine vent length and elbows needed for best drying performance

■ Use the Vent system chart below to determine type of vent

material and hood combinations acceptable to use. NOTE: Do not use vent runs longer than those specified in

the Vent system chart. Exhaust systems longer than those specified will:

■ Shorten the life of the dryer.

■ Reduce performance, resulting in longer drying times and

increased energy usage.

The Vent system chart provides venting requirements that will help to achieve the best drying performance.

InstallLevelingLegs

WARNING

Excessive Weight Hazard Use two or more people to move and install dryer. Failure to do so can result in back or other injury.

1. To protect the floor, use a large flat piece of cardboard from

the dryer carton. Place cardboard under the entire back edge of the dryer.

2. Firmly grasp the body of the dryer. Gently lay the dryer on the

cardboard. See illustration.

Vent system chart

NOTE: Side and bottom exhaust installations have a 90º turn

inside the dryer. To determine maximum exhaust length, add one 90º turn to the chart.

Number of 90º turns or elbows

0 Rigid metal

1 Rigid metal

2 Rigid metal

3 Rigid metal

4 Rigid metal

Type of vent

Flexible metal

Box or louvered hoods

64 ft (20 m) 36 ft (11 m)

54 ft (16.5 m) 31 ft (9.4 m)

44 ft (13.4 m) 27 ft (8.2 m)

35 ft (10.7 m) 25 ft (7.6 m)

27 ft (8.2 m) 23 ft (7 m)

Angled hoods

58 ft (17.7 m) 28 ft (8.5 m)

48 ft (14.6 m) 23 ft (7 m)

38 ft (11.6 m) 19 ft (5.8 m)

29 ft (8.8 m) 17 ft (5.2 m)

21 ft (6.4 m) 15 ft (4.6 m)

InstallVent System

1. Install exhaust hood. Use caulking compound to seal exterior

wall opening around exhaust hood.

2. Connect vent to exhaust hood. Vent must fit inside exhaust

hood. Secure vent to exhaust hood with 4" (10.2 cm) clamp.

3. Run vent to dryer location. Use the straightest path possible.

See “Determine vent path” in “Plan Vent System.” Avoid 90º turns. Use clamps to seal all joints. Do not use duct tape, screws or other fastening devices that extend into the interior of the vent to secure vent.

3. Examine the leveling legs. Find the diamond marking.

4. Screw the legs into the leg holes by hand. Use a wrench to

finish turning the legs until the diamond marking is no longer visible.

5. Place a carton corner post from dryer packaging under each

of the 2 dryer back corners. Stand the dryer up. Slide the dryer on the corner posts until it is close to its final location. Leave enough room to connect the exhaust vent or gas line.

For mobile home use

Gas dryers must be securely fastened to the floor at the time of installation.

Mobile home installations require a Mobile Home Installation Kit. For more information, please reference the service numbers in the “Assistance or Service” section of this manual.

Make GasConnection

1. Remove the red cap from the gas pipe.

2. Using a wrench to tighten, connect the gas supply to the

dryer. Use pipe-joint compound on the threads of all nonflared male fittings. If flexible metal tubing is used, be sure there are no kinks.

A. Flared male fitting B. Non-flared male fitting

NOTE: For LP gas connections, you must use pipe-joint compound resistant to the action of LP gas. Do not use TEFLON

®†

tape.

A combination of pipe fittings must be used to connect the dryer to the existing gas line. Shown is a recommended connection. Your connection may be different, according to the supply line type, size and location.

ConnectVent

1. Using a 4" (10.2 cm) clamp, connect vent to exhaust outlet in

dryer. If connecting to existing vent, make sure the vent is clean. The dryer vent must fit over the dryer exhaust outlet and inside the exhaust hood. Make sure the vent is secured to exhaust hood with a 4" (10.2 cm) clamp.

2. Move dryer into its final location. Do not crush or kink vent.

3. (On gas models) Make sure that there are no kinks in the

flexible gas line.

4. Once the exhaust vent connection is made, remove the

corner posts and cardboard.

Level Dryer

Check the levelness of the dryer. Check levelness first side to side, then front to back.

If the dryer is not level, prop up the dryer using a wood block. Use a wrench to adjust the legs up or down and check again for levelness.

³⁄₈

" flexible gas connector

³⁄₈

" dryer pipe

³⁄₈

" to

³⁄₈

" pipe elbow

³⁄₈

" pipe-to-flare adapter fitting

3. Open the shutoff valve in the supply line. The valve is open

when the handle is parallel to the gas pipe.

A. Closed valve B. Open valve

4. Test all connections by brushing on an approved

noncorrosive leak-detection solution. Bubbles will show a leak. Correct any leak found.

Reverse DoorSwing

You can change your door swing from a right-side opening to a left-side opening, if desired.

Remove the door

1. Open the dryer door. Remove the 4 screws that hold the door

hinge on the front panel of the dryer. Loosen, but do not remove, the screw with the top keyhole opening last (second from the top).

A. Dryer B. Do not remove. C. Dryer door

2. Lift and pull forward on the door so that the keyhole clears

the screw head. Remove the door.

†®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

3. Lay the dryer door on a flat, protected surface with the inside

door assembly facing up. Remove the last screw from Step 1. Remove the 2 screws holding the handle to the door.

4. Remove the 6 screws to release the outer door assembly

from the inner door assembly (see illustration). It is important that you remove only the 6 indicated screws.

Reverse the hinge and hinge bracket

1. Place the inner door, screw head side up, on the work

surface.

2. Remove the 4 screws that hold the hinge to the door.

3. Remove the 2 screws that hold the handle bracket to the

door.

5. Lift the inner door assembly off of the outer door assembly.

Unsnap the handle from the outer door assembly, move it to the other side, and snap in. Set the outer door assembly aside.

4. Move hinge to the other side and reattach with the 4 screws

removed in Step 2.

5. Move handle bracket to the other side and reattach with the

2 screws removed in Step 3.

6. Set the inner door assembly aside.

Reinstalling the door

1. Check for fingerprints on the glass. Clean if necessary.

2. Place the inner door assembly into the outer door assembly.

Align the hinge in the opening on the side. To fit correctly, the inside door assembly edge is completely inside the outside door assembly edge.

3. Reassemble the inner and outer door assemblies with the

6 screws.

4. Replace the 2 handle screws for the door handle of the door

assembly.

5. Use a small flat-blade screwdriver to remove plug strip in the

door opening. Slide the head of the screwdriver under the top portion of the plug strip, being certain not to scratch the dryer surface. Lift up. Repeat in the middle and at the bottom. Remove the plug stripe in the door opening and insert in the opposite side.

6. Insert a screw in the second opening from the top of the

hinge opening and partially tighten. Hang the door by placing the top hinge keyhole over the second screw head and tighten the screw. By putting this screw in first, the door will hang in place while you insert and tighten the remaining 4screws.

Complete Installation

1. Check that all parts are now installed. If there is an extra part,

go back through the steps to see which step was skipped.

2. Check that you have all of your tools.

3. Dispose of/recycle all packaging materials.

4. Check the dryer’s final location. Be sure the vent is not

crushed or kinked.

5. Check that the dryer is level. See “Level Dryer.”

WARNING

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

A. Dryer door B. Dryer C. Insert this screw first.

7. Close the door and check that it latches securely.

6. Plug into a grounded 3 prong outlet. Turn on power.

7. Remove any protective film or tape remaining on the dryer.

8. Read “Dryer Use.”

9. Wipe the dryer drum interior thoroughly with a damp cloth to

remove any dust.

10. Select a Timed Dry heated cycle, and start the dryer. Do not

select the Air Only modifier.

If the dryer will not start, check the following:

■ Dryer is plugged into a grounded 3 prong outlet.

■ Electrical supply is connected.

■ Household fuse is intact and tight, or circuit breaker has

not tripped.

■ Dryer door is closed.

11. When the dryer has been running for 5 minutes, open the

dryer door and feel for heat. If you feel heat, cancel cycle and close door. If you do not feel heat, turn off the dryer and check that the gas supply line shutoff valve is open.

■ If the gas supply line shutoff valve is closed, open it, then

repeat the 5-minute test as outlined above.

■ If the gas supply line shutoff valve is open, contact a

qualified technician.

DRYER USE

Starting Your Dryer

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from dryer.

Do not dry anything that has ever had anything flammable on it (even after washing).

Failure to follow these instructions can result in death, explosion, or fire.

The following is a guide to starting your dryer. Please refer to specific sections of this manual for more detailed information.

1. Clean lint screen before each load. See “Cleaning the Lint

Screen.”

2. Place laundry into dryer and shut door.

3. Rotate the dial to select either an Automatic or Manual Cycle

then press the CONTROL ON button. The preset settings and drying time for the cycle chosen will be displayed.

To use an Automatic Cycle

■ Point the dial to an Automatic Cycle.

■ Select DRYNESS LEVEL to adjust how dry you want the

load to be. The time displayed is an estimated length of the cycle based on the Dryness Level selected. As the cycle runs, the control senses the dryness of the load and adjusts the time automatically for the selected Dryness Level.

WARNING

Fire Hazard No washer can completely remove oil. Do not dry anything that has ever had any type of oil on

it (including cooking oils). Items containing foam, rubber, or plastic must be dried

on a clothesline or by using an Air Cycle. Failure to follow these instructions can result in death

or fire.

NOTE: Time is not adjustable for Automatic Cycles. Pressing the Manual Dry Time (- or +) buttons will cause a triple beep, indicating that the time cannot be changed.

■ Press the EXTRA CARE feature button if this option is

desired.

■ Press the CYCLE END SIGNAL button to set signal

volume to desired level.

■ Press (and hold) HOLD TO START button until dryer starts

(about 1 second).

Once an Automatic Cycle has started, the Extra Care feature and the Cycle End Signal level can be adjusted. Press the OFF key twice to stop the dryer and clear the settings, allowing you to select another cycle and Dryness Level.

How Auto Moisture Sensing Plus works

The Even-Heat™ feature improves drying performance with Auto Moisture Sensing Plus, which advances the cycle as moisture is extracted from clothing. A thermistor (electronic temperature sensor) and moisture sensing strips in the dryer drum help measure the amount of moisture in the clothes as they pass. An electronic control determines the load type to help save time, avoid overdrying, and increase the accuracy of the end dryness level. After the first 5 minutes of an automatic cycle, the estimated time display will adjust based on the approximate load size, cycle, dryness level selected and amount of moisture left in the clothes. When the clothes have reached approximately 80% of the dryness level selected, the estimated time display will adjust again, showing the final drying time. Auto Moisture Sensing Plus takes the guesswork out of drying time and enhances fabric care.

To use a Manual Cycle

■ Rotate the dial to select a Manual Cycle.

Press the MANUAL DRY TIME (- or +) buttons until the desired drying time is displayed. Tap - or +, and the time will change by 1-minute intervals. Press and hold - or +, and the time will change by 5-minute intervals. The initial time displayed is the actual drying time.

NOTE: The Manual Dry Time feature can be used only with Manual Cycles.

■ Press TEMP until the desired temperature glows.

NOTE: Pressing the Dryness Level button will cause the triple beep indicating that this option is not selectable. Also, a Dryness Level is not indicated.

■ Press the EXTRA CARE feature button if this option is

desired.

■ Press the CYCLE END SIGNAL button to set volume to

desired level.

■ Press (and hold) HOLD TO START button until dryer starts

(about 1 second).

While a Manual Cycle is running, you can change the settings for Time, Temperature, the Extra Care feature, and the Cycle End Signal. Press the OFF button twice to stop the dryer and clear the settings, allowing you to select another cycle.

StoppingYour Dryer

To stop your dryer at any time

Press OFF twice or open the door.

Pausing orRestarting

To pause the dryer at any time

Open the door or press OFF once.

To restart the dryer

Close the door and press (and hold) HOLD TO START button until dryer starts.

NOTE: Drying will continue from where the cycle was interrupted if you close the door and press Start within 5 minutes. If the cycle is interrupted for more than 5 minutes, the dryer will shut off. Select new cycle settings before restarting the dryer.

Control Locked

This feature allows you to lock your settings to avoid unintended use of the dryer. You can also use the Control Locked feature to avoid unintended cycle or option changes during dryer operation.

To enable the Control Locked feature when dryer is running:

Press and hold the CYCLE END SIGNAL button for 3 seconds. The control is locked when a single beep is heard and the Control Locked status light is on.

■ When the dryer is off, it is not necessary to press the Control

On button before activating the Control Locked feature.

To unlock:

Press and hold the CYCLE END SIGNAL button for 3 seconds to turn this feature off.

NOTE: When the dryer is running and Control Locked is on, the dryer can be stopped by pressing the Off button, but can’t be restarted until the control is unlocked.

Drying andCycle Tips

Select the correct cycle and dryness level or temperature for your load. If an Automatic Cycle is running, the display shows the estimated cycle time when your dryer is automatically sensing the dryness level of your load. If a Manual Cycle is running, the display shows the exact number of minutes remaining in the cycle.

Cool Down tumbles the load without heat during the last few minutes of all cycles. Cool Down makes the loads easier to handle and reduces wrinkling. The length of the Cool Down depends on the load size and dryness level.

Drying tips

■ Follow care label directions when they are available.

■ If desired, add a fabric softener sheet. Follow package

instructions.

■ Remove the load from the dryer as soon as tumbling stops to

reduce wrinkling. This is especially important for permanent press, knits and synthetic fabrics.

■ Avoid drying heavy work clothes with lighter fabrics. This

could cause overdrying of lighter fabrics, leading to increased shrinking or wrinkling.

Cycle tips

■ Dry most loads using the preset cycle settings.

■ Refer to the Automatic or Manual Preset Cycle Settings chart

(in the “Cycles” section) for a guide to drying various loads.

■ Drying temperature and Dryness Level are preset when

you choose an Automatic Cycle. You can choose a different dryness level, depending on your load by pressing the DRYNESS LEVEL button to select MORE or LESS.

■ If you wish to adjust the cycle length of a Manual Cycle,

you must press the MANUAL DRY TIME (- or +) buttons. Adjust the temperature of a Manual Cycle by pressing TEMP until the desired temperature is selected.

NOTE: You cannot choose a Dryness Level with Manual Cycles.

StatusLights

You may follow the progress of your dryer with the drying status indicator lights.

Sensing

When a cycle is first turned on, the Sensing light glows until a wet item is detected.

■ In an Automatic Cycle, if a wet item has not been detected

within 10 minutes, the Sensing light will turn off and the dryer will shut down.

■ In a Manual Cycle, if a wet item is not detected after

10 minutes the Wet light turns on and the selected cycle continues.

Wet

The Wet light will turn on when a wet item has been detected in the dryer. The Wet light will remain on until:

■ The damp dry point is reached in an Automatic Cycle.

■ The dryer enters the cool down period in a Manual Cycle.

Damp

The Damp light indicates that the load has reached the damp dry level.

NOTE: The Damp light is not used with Manual Cycles.

Cycles

Select the drying cycle that matches the type of load you are drying. See Automatic preset or Manual preset cycle settings charts.

Cycle control knob

Automatic Cycles

Automatic Cycles allow you to match the cycle to the load you are drying. See the following Automatic preset cycle settings chart. Each cycle dries certain fabrics at the recommended temperature. A sensor detects the moisture in the load and automatically adjusts the drying time for optimal drying.

Heavy Duty

Use this cycle to get High heat for heavy fabrics such as cotton towels or bedspreads.

Normal

Use this cycle to get Medium heat for drying sturdy fabrics such as work clothes.

Casual

Use this cycle to get Medium heat for drying no-iron fabrics such as sport shirts, casual business clothes and permanent press blends.

Cool Down

The Cool Down light glows during the cool down part of the cycle. Laundry is cooling down for ease in handling.

Cycle Complete

The Cycle Complete light glows when a drying cycle is finished. If the Extra Care feature has been selected, the Extra Care feature indicator light will also be on.

The Cycle Complete light turns off 1 hour after the end of a drying cycle (including the Extra Care cycle of 2 hours), when Off is pressed, or when the door is opened.

Extra Care Feature

The Extra Care feature light glows when this option is selected. This indicator stays on with the Cycle Complete light.

Control Locked

The Control Locked light glows when this option is enabled.

Indicator lights

Other indicator lights on the control panel show Cycle, Temperature and Cycle End Signal settings selected.

The time display will indicate the estimated or actual time remaining in a cycle.

Delicate

Use this cycle to get Low heat for drying synthetic fabrics, washable knit fabrics and no-iron finishes.

Super Delicate

Use this cycle to get Extra-Low heat to gently dry items such as lingerie, exercise wear or sheer curtains.

Automatic preset cycle settings

Automatic Cycles Load Type

HEAVY DUTY

Heavyweight, towels

NORMAL

Corduroys, work clothes

CASUAL

Permanent press, synthetics

DELICATE

Lingerie, blouses, washable woolens

SUPER DELICATE

Exercise wear, sheer curtains, lace

Te mp . T im e *

(Minutes)

High 40

Medium 34

Medium 36

Low 28

Extra Low 22

*Estimated Time with Dryness Level (medium) setting.

Manual Cycles

Use Manual Cycles to select a specific amount of drying time and a drying temperature. When a Manual Cycle is selected, the ESTIMATED TIME REMAINING display shows the actual time remaining in your cycle. You can change the actual time in the cycle by pressing the Manual Dry Time (- or +) buttons.

Timed Dry

Use this cycle to complete drying if items are still damp after an Automatic Cycle. Timed Dry is also useful for drying heavyweight and bulky items, such as bedspreads and work clothes.

Touchup

Use this setting to help smooth out wrinkles from such items as clothes packed in a suitcase or items wrinkled from being left in the dryer too long.

Rapid Dry

Use this cycle for drying small loads or loads that need a short drying time.

Temperature

Temperature settings are used with the Manual Cycles. Press TEMP until the desired temperature setting glows. Temperature settings cannot be used with the Automatic Cycles.

Air Only

Use the Air Only setting for items that require drying without heat such as rubber, plastic and heat-sensitive fabrics. This chart shows examples of items that can be dried using Air Only.

Manual preset cycle settings

Manual Cycles Load Type

TIMED DRY

Heavyweight, bulky items, bedspreads, work clothes

TOUCHUP Helps to smooth out wrinkles

RAPID DRY

Small loads

Temp. Default Time

(Minutes)

High 40

Medium 20

High 27

Additional Features

Extra Care Feature

When you are unable to remove a load of clothes from the dryer as soon as it stops, wrinkles can form. The Extra Care feature periodically tumbles, rearranges and fluffs the load to help reduce wrinkling.

■ Press the Extra Care feature to get up to 120 minutes of heat-

free, periodic tumbling at the end of a cycle.

■ Stop at any time by pressing the Extra Care feature or

opening the dryer door.

■ For the Casual Cycle, the Extra Care feature is preset to “On.”

The other Automatic Cycles will retain the Extra Care feature setting. (For example, if you select the Extra Care feature in the Normal cycle, the Extra Care feature will be on the next time you select the Normal cycle.)

NOTE: If you do not select the Extra Care feature, the dryer stops after the cool down period.

Type of Load Time*

Foam rubber - pillows, padded bras, stuffed toys

Plastic - Shower curtains, tablecloths 20 - 30

Rubber-backed rugs 40 - 50

Olefin, polypropylene, sheer nylon 10 - 20

*Reset time to complete drying, if needed.

(Minutes)

20 - 30

When using Air Only

■ Check that coverings are securely stitched.

■ Shake and fluff pillows by hand periodically during the cycle.

■ Dry item completely. Foam rubber pillows are slow to dry.

NOTE: Automatic Cycles are not available when using the Air Only setting.

Cycle End Signal

The Cycle End Signal produces an audible sound when the drying cycle is finished. Promptly removing clothes at the end of the cycle reduces wrinkling.

Press and release the CYCLE END SIGNAL to adjust the sound level or turn off the signal.

NOTE: When the Extra Care feature is selected and the Cycle End Signal is on, an audible sound will emit every 5 minutes until the clothes are removed, or the Extra Care feature is finished.

Drying Rack

The drying rack is useful for drying items you would not necessarily want to tumble dry or that you would normally line dry (for example, sweaters).

To use the drying rack

Do not remove the lint screen.

1. Open dryer door.

This chart shows examples of items that can be rack dried and the suggested cycle, temperature setting and drying time. Actual drying time will depend on the amount of moisture items hold.

Rack Dry Setting Temp. Time*

Wool Sweaters

Block to shape and lay flat on the rack

Timed Dry

Low 60

A. Front edge

2. Place drying rack inside dryer drum, positioning the back wire

on the ledge of the inner dryer back panel. Push down on front edge of drying rack to secure over the lint screen.

A. Dryer rack front edge B. Dryer back panel

3. Put the wet items on top of the rack. Leave space between

the items so air can reach all the surfaces.

NOTE: Do not allow items to hang over the edge of the rack.

Stuffed toys or pillows

Cotton or polyester fiber filled

Stuffed toys or pillows

Foam rubber filled

Sneakers or canvas shoes Timed

*(Minutes) Reset time to complete drying, if needed.

Timed Dry

Dry

Low 60

Air Only (no heat)

DRYER CARE

Cleaning theDryer Location

Keep dryer area clear and free from items that would obstruct the flow of combustion and ventilation air.

WARNING

4. Close the door.

5. Select a timed drying cycle and temperature, or an air cycle

(see following chart). Items containing foam, rubber or plastic must be dried on a clothesline or by using the Air Only temperature setting.

6. You must select a time by pressing the MANUAL DRY TIME

(- or +) buttons. Reset time as needed to complete drying. Refer to the following table.

7. Press (and hold) HOLD TO START button (about 1 second). NOTE: You must remove rack for normal tumbling. Do not use

automatic cycles with the drying rack.

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from dryer.

Place dryer at least 18 inches (46 cm) above the floor for a garage installation.

Failure to do so can result in death, explosion, or fire.

Cleaning the Lint Screen

Every load cleaning

The lint screen is located in the door opening of the dryer. A screen blocked by lint can increase drying time.

To clean

1. Pull the lint screen straight up. Roll lint off the screen with

your fingers. Do not rinse or wash screen to remove lint. Wet lint is hard to remove.

2. Push the lint screen firmly back into place. IMPORTANT:

■ Do not run the dryer with the lint screen loose, damaged,

blocked or missing. Doing so can cause overheating and damage to both the dryer and fabrics.

■ If lint falls off the screen into the dryer during removal, check

the exhaust hood and remove the lint. See “Vent ing Requirements.”

As needed cleaning

Laundry detergent and fabric softener residue can build up on the lint screen. This buildup can cause longer drying times for your clothes, or cause the dryer to stop before your load is completely dry. The screen is probably clogged if lint falls off the screen.

Clean the lint screen with a nylon brush every 6 months, or more frequently, if it becomes clogged due to a residue buildup.

To wash

1. Roll lint off the screen with your fingers.

2. Wet both sides of lint screen with hot water.

3. Wet a nylon brush with hot water and liquid detergent. Scrub

lint screen with the brush to remove residue buildup.

Vacation andMovingCare

Vacation care

Operate your dryer only when you are at home. If you will be on vacation or not using your dryer for an extended period of time, you should:

1. Unplug dryer or disconnect power.

2. Close shutoff valve in gas supply line.

3. Clean lint screen. See “Cleaning the Lint Screen.”

Moving care

1. Unplug the power supply cord.

2. Close shutoff valve in gas supply line.

3. Disconnect gas supply line pipe and remove fittings attached

to dryer pipe.

4. Cap the open fuel supply line.

5. Make sure leveling legs are secure in dryer base.

6. Use masking tape to secure dryer door.

Changing theDrum Light

The dryer light automatically turns on inside the dryer drum when you open the door.

4. Rinse screen with hot water.

5. Thoroughly dry lint screen with a clean towel. Replace screen

in dryer.

Cleaning theDryer Interior

To clean dryer drum

1. Make a paste with powdered laundry detergent and very

warm water.

2. Apply paste to a soft cloth. OR

Apply a liquid, nonflammable household cleaner to the stained area and rub with a soft cloth until all excess dye and stains are removed.

3. Wipe drum thoroughly with a damp cloth.

4. Tumble a load of clean cloths or towels to dry drum.

NOTE: Garments that contain unstable dyes, such as denim blue

jeans or brightly colored cotton items, may discolor the dryer interior. These stains are not harmful to your dryer and will not stain future loads of clothes. Dry unstable dye items inside out to avoid dye transfer.

Removing AccumulatedLint

From Inside the Dryer Cabinet

Lint should be removed every 2 years, or more often, depending on dryer usage. Cleaning should be done by a qualified person.

To change the drum light

1. Unplug dryer or disconnect power.

2. Open the dryer door. Locate the light bulb cover on the back

wall of the dryer. Remove the screw located in the lower right corner of the cover. Remove the cover.

3. Turn bulb counterclockwise. Replace the bulb with a 10-watt

appliance bulb only. Replace the cover and secure with the screw.

4. Plug in dryer or reconnect power.

From the Exhaust Vent

Lint should be removed every 2 years, or more often, depending on dryer usage.

TROUBLESHOOTING

First try the solutions suggested here and possibly avoid the cost of a service call...

Dryer Operation

Dryer will not run

■ Has a household fuse blown, or has a circuit breaker

tripped?

There may be 2 fuses or circuit breakers for the dryer. Check that both fuses are intact and tight, or that both circuit breakers have not tripped. Replace the fuse or reset the circuit breaker. If the problem continues, call an electrician.

■ Was a regular fuse used? Use a time-delay fuse.

■ Is the dryer door firmly closed?

■ Was the Start button firmly pressed? Large loads may

require pressing and holding the Start button for 2-5 seconds.

No heat

■ Has a household fuse blown, or has a circuit breaker

tripped?

The drum may be turning, but you may not have heat. Replace the fuse or reset the circuit breaker. If the problem continues, call an electrician.

■ Is the valve open on the gas supply line?

Unusual sounds

■ Has the dryer had a period of non-use?

If the dryer hasn’t been used for a while, there may be a thumping sound during the first few minutes of operation.

■ Is a coin, button, or paper clip caught between the drum

and front or rear of the dryer? Check the front and rear edges of the drum for small objects. Clean out pockets before laundering.

■ Is it a gas dryer?

The gas valve clicking is a normal operating sound.

■ Are the four legs installed, and is the dryer level front to

back and side to side? The dryer may vibrate if not properly installed. See “Installation Instructions.”

■ Is the clothing knotted or balled up?

When balled up, the load will bounce, causing the dryer to vibrate. Separate the load items and restart the dryer.

Dryer Results

Clothes are not drying satisfactorily, drying times are too long, or load is too hot

■ Is the lint screen clogged with lint?

Lint screen should be cleaned before each load.

WARNING

Fire Hazard Use a heavy metal vent. Do not use a plastic vent. Do not use a metal foil vent. Failure to follow these instructions can result in death

or fire.

■ Is the exhaust vent or outside exhaust hood clogged with

lint, restricting air movement? Run the dryer for 5-10 minutes. Hold your hand under the outside exhaust hood to check air movement. If you do not feel air movement, clean exhaust system of lint or replace exhaust vent with heavy metal or flexible metal vent. See “Installation Instructions.”

■ Are fabric softener sheets blocking the grille?

Use only one fabric softener sheet, and use it only once.

■ Is the exhaust vent the correct length?

Check that the exhaust vent is not too long or has too many turns. Long venting will increase drying times. See “Installation Instructions.”

■ Is the exhaust vent diameter the correct size?

Use 4" (10.2 cm) diameter vent material.

WARNING

Dryer displaying code message

■ “PF” (power failure), check the following:

Was the drying cycle interrupted by a power failure? Press and hold START to restart the dryer.

■ “E” Variable (E1, E2, E3) service codes:

Call for service.

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from dryer.

Place dryer at least 18 inches (46 cm) above the floor for a garage installation.

Failure to do so can result in death, explosion, or fire.

■ Is the dryer located in a room with temperature below

45ºF (7ºC)? Proper operation of dryer cycles requires temperatures above 45ºF (7ºC).

■ Is the dryer located in a closet?

Closet doors must have ventilation openings at the top and bottom of the door. For most installations, the rear of the dryer requires 5½" (14 cm). See “Installation Instructions.”

■ Has an air dry cycle been selected?

Select the right cycle for the types of garments being dried. See “Cycles.”

■ Is the load too large and heavy to dry quickly?

Separate the load to tumble freely.

Cycle time too short

WARNING

Excessive Weight Hazard Use two or more people to move and install dryer. Failure to do so can result in back or other injury.

■ Is the automatic cycle ending early?

The load may not be contacting the sensor strips. Level the dryer.

Change the dryness level setting on Automatic Cycles. Increasing or decreasing the dryness level will change the amount of drying time in a cycle.

Lint on load

■ Is the lint screen clogged?

Clean lint screen. Check for air movement.

Stains on load or drum

■ Was dryer fabric softener properly used?

Add dryer fabric softener sheets at the beginning of the cycle. Fabric softener sheets added to a partially dried load can stain your garments.

Drum stains are caused by dyes in clothing (usually blue jeans). This will not transfer to other clothing.

Loads are wrinkled

■ Was the load removed from dryer at the end of the cycle?

■ Was the dryer overloaded? Dry smaller loads that can

tumble freely.

Odors

■ Have you recently been painting, staining or varnishing in

the area where your dryer is located?

If so, ventilate the area. When the odors or fumes are gone from the area, rewash and dry the clothing.

ASSISTANCE OR SERVICE

Before calling for assistance or service, please check “Troubleshooting.” It may save you the cost of a service call. If you still need help, follow the instructions below.

When calling, please know the purchase date and the complete model and serial number of your appliance. This information will help us to better respond to your request.

If you need replacement parts

If you need to order replacement parts, we recommend that you use only factory specified parts. Factory specified parts will fit right and work right because they are made with the same precision used to build every new KITCHENAID

To locate factory specified parts in your area, call our Customer eXperience Center telephone number or your nearest designated service center.

In the U.S.A.

Call the KitchenAid Customer eXperience Center toll free: 1-800-422-1230.

Our consultants provide assistance with:

■ Features and specifications on our full line of appliances.

■ Installation information.

■ Use and maintenance procedures.

■ Accessory and repair parts sales.

■ Specialized customer assistance (Spanish speaking, hearing

impaired, limited vision, etc.).

■ Referrals to local dealers, repair parts distributors and service

companies. KitchenAid designated service technicians are trained to fulfill the product warranty and provide afterwarranty service, anywhere in the United States.

To locate the KitchenAid designated service company in your area, you can also look in your telephone directory Yellow Pages.

appliance.

For further assistance

If you need further assistance, you can write to KitchenAid with any questions or concerns at:

KitchenAid Brand Home Appliances Customer eXperience Center 553 Benson Road Benton Harbor, MI 49022-2692

Please include a daytime phone number in your correspondence.

In Canada

Call the KitchenAid Canada Customer Interaction Centre toll free:

1-800-807-6777. Our consultants provide assistance with:

■ Features and specifications on our full line of appliances.

■ Use and maintenance procedures.

■ Accessory and repair parts sales.

■ Referrals to local dealers, repair parts distributors and service

companies. KitchenAid Canada designated service technicians are trained to fulfill the product warranty and provide after-warranty service, anywhere in Canada.

For further assistance

If you need further assistance, you can write to KitchenAid Canada with any questions or concerns at:

Customer Interaction Centre KitchenAid Canada 1901 Minnesota Court Mississauga, Ontario L5N 3A7

Please include a daytime phone number in your correspondence.

+ 50 hidden pages