INSTRUCTIONS FOR USE
BEFORE USING THE HOOD
PROTECTING THE ENVIRONMENT
PRECAUTIONS AND GENERAL
RECOMMENDATIONS
USING THE HOOD
CARE AND MAINTENANCE
TROUBLESHOOTING GUIDE
AFTER-SALES SERVICE
INSTALLATION
19
BEFORE USING THE HOOD
• Please read these instructions carefully in order
to get the best out of your new hood.
• This appliance is designed to be used only by adults.
• The appliance is not intended for use by children or
infirm persons without supervision. Make sure that
children do not play with the appliance.
• Packaging materials can be dangerous for children.
Keep packaging materials (plastic bags, polystyrene,
etc.) well out of their reach.
• Make sure the hood has not been damaged during
transport.
• Installation and connection to the mains and exhaust
ducts must be carried out by a qualified technician, in
accordance with the manufacturer's instructions and
local safety regulations.
PROTECTING THE ENVIRONMENT
1. Packaging
Packaging materials are 100% recyclable and are marked
with the recycling symbol . Dispose of packaging
materials in compliance with local waste disposal
regulations. Packaging materials can be dangerous for
children. Keep packaging materials (plastic bags,
polystyrene, etc.) well out of their reach.
2. Appliance
This appliance is marked in compliance with European
Directive 2002/96/EC on Waste Electrical and Electronic
Equipment (WEEE).
By ensuring this product is disposed of correctly, you will
help prevent potential negative consequences for the
environment and human health, which could otherwise
be caused by inappropriate waste handling of this
product.
The symbol on the appliance or accompanying
documentation indicates that this product should not be
disposed of as unsorted municipal waste but must be
taken to a collection point for the treatment of WEEE.
Disposal must be carried out in accordance with local
environmental regulations for waste disposal.
For more detailed information about treatment, recovery
and recycling of this product, please contact your local
city office, your household waste disposal service or the
shop where you purchased the product.
PRECAUTIONS AND GENERAL
RECOMMENDATIONS
1. Always disconnect the hood before cleaning or
carrying out maintenance by unplugging it or
switching off the power supply.
2. Exhaust air must not be conveyed through the same
flue used by the heating system or other nonelectrical appliances.
3. Do not “flambé” food under the hood. Naked
flames could cause fire.
4. Never leave the pan unattended when frying
since the cooking oil could ignite.
5. Regular maintenance guarantees smooth hood
operation and high performance.
6. If the hood is used in extractor mode together with
cookers, ambient negative pressure must not exceed
4 Pa (4 x 10
7. If the hood is used together with non-electrically
powered appliances, ambient negative pressure must
not exceed 4Pa
(4 x 10-5 bars). For this reason, make sure the room
is adequately ventilated.
-5
bars).
20
8. The room must be adequately ventilated when the
hood is used together with appliances powered by
gas or other fuels.
9. Regularly remove dirt deposits. Regularly clean or
replace filters. Never use flammable materials as
hoses for extracted air.
10. If the power cable is damaged, it must be
replaced by the After-Sales Service or a
qualified electrician in order to avoid hazards.
Note: always wear work gloves for all installation and
maintenance operations.
Declaration of conformity
This product has been designed, manufactured and sold
in conformity to the following standards:
- the safety standards of the
“Low Voltage” Directive 73/23/EEC
- protection requirements of
“EMC” Directive 89/336/EEC amended by Directive
93/68/EEC.
USING THE HOOD
Switch on the hood a few minutes before starting to cook and leave it running for at least 5 minutes after you have
finished.
1. Pull out the steam drawer (depending on model). This improves hood performance.
2. Turn the speed selector to the required speed setting according to the quantity of fumes and steam to be
extracted.
3. Switch off the hood 5 minutes after you have finished cooking.
4. Close the steam-collecting drawer (where fitted).
CARE AND MAINTENANCE
Always disconnect the hood before cleaning or carrying out maintenance by unplugging it or switching
off the power supply.
Grease filter
• The sponge grease filter should be washed in hot soapy water once a month
(soak for 1-2 hours, do not wring, leave to dry and then remount. If necessary, repeat the process. Replace with
a new filter every 5-6 washes).
• The grease filter paper should be replaced at least once a month.
• Grease filter paper with saturation indicator should be replaced at least every two months or whenever the
colour becomes visible through the holes of the grille.
The paper filter is coloured on one side. This colour should not be visible through the grille holes when the filter
is installed.
• Metal grease filters should be washed once a month either by hand or in a dishwasher at a low temperature and
in a short cycle. Leave filter to dry before remounting it. Washing in a dishwasher can cause grease filters to turn
white, but this in no way affects efficiency.
Whenever cleaning or replacing the grease filters, clean all other exposed parts of the hood.
Carbon filter
(“Air recirculation mode”, see following page)
The carbon filter cannot be washed or regenerated. In some cases, carbon filters can be washed, but only when
specified in the attached Product Description Sheet.
Replace the carbon filter (normal usage)
every 6 months (Rectangular carbon filter)
every 4 months (Circular carbon filter).
Replacing bulbs
1. When replacing the bulb, be sure it is cool before touching it and check the wattage.
2. Pull out the steam-collecting drawer (depending on model).
3. Open the grille or light fixture and remove the grease filter.
4. Remove the burnt-out bulb and replace it with a new one of the same wattage. Close the grille, light fixture or
metal grease filter.
Cleaning the hood
Use a soft cloth with methylated spirits or a mild liquid detergent. Never use abrasive substances. never clean the
appliance with high pressure water or steam cleaning equipment.
War nin g! Failure to observe the instructions for cleaning the appliance and replacing or washing the filters may cause
a fire.
TROUBLESHOOTING GUIDE
Hood does not work:
• Is the power plug properly inserted in the mains
socket?
• Is there a power failure?
• Is the mains fuse OK?
Insufficient suction power:
• Is the right extraction speed selected?
• Do the filters need to be cleaned or replaced?
• Are the air outlets blocked?
Light does not work:
• Does the bulb need to be replaced?
• Is the bulb correctly fitted?
• Is the mains fuse OK?
Never try to carry out any repair by yourself other
than fixing the above-mentioned problems.
21
AFTER-SALES SERVICE
Before calling Technical Assistance
1. Check to see if you can fix the problem yourself
(see “Troubleshooting Guide”).
2. Switch the hood off for a few minutes then switch it
back on and see if the problem has gone.
3. If the problem persists, call Technical Assistance.
Specify:
• the nature of the problem,
• the model,
• your full address,
• your telephone number and area code.
• The service code (number below the word
SERVICE on the rating plate inside the hood behind
the grease filter).
INSTALLATION
When installing the hood, the minimum distances from the cooktop must be respected, and the
numerical sequence and additional instructions must be followed exactly as indicated on the Installation
sheet.
If the installation instructions for a gas cooker specify a greater distance, then this distance must be
observed.
The exhaust pipe and clamps are not supplied and must be bought separately.
External Exhaust Mode
A - see also installation sheet)
(
Cooking fumes and vapours are conveyed outside through a duct connected to the hood by means of a collar.
The outlet duct diameter must be the same as that of the collar.
If a flue-damper is to be installed, check that it can open and close freely when installation of the exhaust
duct is complete.
The hood can be supplied with one (upper) or two (upper and rear) exhaust outlet holes.
The hood is usually set up for using the upper exhaust outlet.
1. The collar must be seated in the upper exhaust outlet.
Use the rear exhaust outlet (where present).
1. Where fitted, remove the cover closing off the rear outlet and collar.
2. Some models are fitted with a plastic deflector that closes off the rear outlet. If fitted, remove it.
3. Fit the collar in the rear outlet.
4. Put the cover (if fitted) in the upper outlet.
War ning ! If the hood has a carbon filter, this should be removed.
Check that the switch inside the hood (if fitted) is on position “A” Extractor; if not, set it to this position.
Filter Hood
F - see also installation sheet)
(
Air is filtered through a carbon filter and returned to the room. The filtered air is released towards the kitchen
ceiling.
Warning! If the hood does not have a carbon filter, order one and fit it before use.
Check that the switch inside the hood (if fitted) is on position “F” Filter; if not, set it to this position.
If the plug is provided, close off the upper exhaust hole.
Electrical connections
Before connecting the hood, make sure the voltage indicated on the rating plate corresponds to the voltage in your
home.
The plate is located inside the hood behind the grille.
If the hood is fitted with a standard plug, insert it into a matching standard socket in an easily accessible location.
If the hood is not fitted with a plug, fit one that conforms to applicable standards or use a double-pole switch that
conforms to applicable standards with a minimum contact separation of 3mm, in an easily accessible location.
The Manufacturer shall not be liable for any damage or problem arising from the failure to comply with
the above-mentioned instructions.
22
Loading...