Machine operation
Additional information (including troubleshooting and service) can be found in the individual sections of the
Instructions For Use.
Sort laundry according to
care symbols
Do not tumble dry
Suitable for tumble drying -
at low temperatures
Suitable for tumble drying
Prepare laundry
Load dryer
Select programme
Select options
(if available)
Start dryer
Sort laundry by:
Material thickness:
separate laundry according to weight (e.g. dry towels and thin underwear separately).
Type of material:
Dryness level:
Do not tumble dry:
metallic decorations, bulky items such as sleeping bags or pillows.
Check that all fastenings are closed and that pockets are empty. Ensure that there are
no cigarette lighters in the wash. Turn laundry inside out.
Place laundry loosely in the drum to achieve even drying throughout. Then close the
door.
Select the required drying programme by turning the programme selector knob (for
information, refer to programme table).
Select the required option by pressing the corresponding button.
The indicator lamp above the relevant button lights up to confirm your selection.
A fast blinking LED indicates that an invalid selection has been made (incompatible
option). Press the button again to cancel the option.
Start the drying programme by pressing the
The relevant indicator lamp lights up.
Changing programme selection:
drying, the dryer stops. The
To run the new programme, press the
Interrupting programme:
button and open the door. Wait at least 5 minutes, to allow the laundry to cool down,
before unloading the dryer. For your safety, the drying cycle stops automatically if you
open the door. To restart the cycle after opening the door, press the
button again.
Warning:
items are quickly removed and spread out so that the heat is dissipated.
never stop a tumble dryer before the end of the drying cycle, unless all
whenever the load is greater than the dryer can handle,
cotton (linen); synthetic textiles (easy care).
cupboard dry, iron dry etc.
woollens, silk, nylon stockings, delicate embroidery, fabrics with
“Start (Pause)”
if the selected programme is changed during
“Start (Pause)”
to interrupt a drying cycle, press the
indicator lamp flashes.
“Start (Pause)”
button.
button again.
“Start (Pause)”
“Start (Pause)”
The final part of a drying cycle occurs without heat (cool-down cycle) to ensure that
Programme end -
unload dryer
Switch dryer off
Set the programme selector knob to “Off” (“O”).
Cleaning the lint filter:
fingertips. Close lint filter and push firmly back into place (more detailed informations are given in the Instructions For Use).
Emptying the water container:
completely back into place.
Please note:
thoroughly in plenty of water before drying. Never dry rubber objects or objects stained with vegetable oils in the dryer.
The Manufacturer is not liable for any damage to laundry resulting from inadequate or incorrect fabric care instructions which
have been provided with the garment or article.
only use additives/plastic items specified as dryer safe and rinse items that have been treated with stain remover
open door, pull lint filter up and out of machine and open it. Brush lint using a soft brush or your
pull container out by the handle and empty. Replace the container when empty by pushing it
the items reach a lower temperature to avoid wrinkling.
take the laundry out of the dryer. The drying process is complete and the anti-
End:
crease phase has been reached (active).
Set the programme selector knob to “Off” (“O”).
1
(in minutes)
drying times
Approximate
Wet
load
wet
Ver y
delay
65’
75’
load
180’
210’
60’
70’
160’
185’
55’
65’
135’
160’
40’
50’
110’
130’
25’
35’
70’
95’
20’
25’
50’
70’
15’
20’
45’
60’
10’ 20’ 30’
40’ 60’ 90’
Gentle Buzzer Start
of load
Vol u me
Fabrics
Type o f te x ti le
X X X
*
kg
3.0
9.0
X X X
3.0
9.0
Cotton or linen
hot wash/coloured laundry
X X X
3.0
9.0
Max. 9 kg
X X X
3.0
9.0
X X X
1.0
4.5
(ironing not required) laundry
Synthetic, mixed fibre or cotton easy care
X X X
1.0
4.5
X X X
1.0
4.5
Max. 4.5 kg
— — X — — —
— X X —
All fabrics
2
Overview of programmes Options
Programmes / Drying levels
Multi-layered, thick laundry such as: terry towels, terry
towelling bath robes.
Extra dry
Terry towels, dry towels, bed linen, underwear.
Cupboard dry plus
Similar types of laundry which do not require ironing such
as: dry towels, bed linen, underwear, baby clothes,
T-shirts, cotton socks.
Cupboard dry **
Cotton
Laundry which requires ironing such as: bed and table
linen, dry towels, T-shirts, polo shirts, work clothes.
Laundry with thick, multi-layered areas such as: bed and
table linen, track suits, anoraks, blankets.
Laundry which does not require ironing such as: shirts,
blouses, T-shirts, sportswear.
Laundry which requires ironing such as: trousers, dresses,
skirts, shirts, blouses.
Iron dry **
Extra dry
Cupboard dry **
Iron dry
Easy care
All textiles.
Laundry is aired, refreshed and loosen
up for 30 minutes without heating.
Airing
Additional drying time for textiles that are not suitable for
other programmes, or for finalisation of the drying
process.
10’ 20’ 30’ 40’ 60’ 90’
times
Drying
Weight of average and maximum load.
*
Test programmes according to EN 61121, tested with maximum rated load capacity.
**
How to proceed if...
...you want to check the dryer yourself first:
(If your machine is not functioning correctly, please
check the following points before calling the Customer Service department - also refer to relevant
section in the Instructions For Use).
• Was the inserted laundry too wet (washing machine spin speed less than 1000 rpm)?
• Is the lint filter dirty? (filter indicator light on)
• Is the heat exchanger dirty? (for more information, refer to the Instructions For Use)
• Is the room temperature too high?
Drying takes too long/
Laundry is not dry enough
The dryer does not
operate (after a power
failure, always press the
“Start (Pause)” button)
Lint filter, water container
or heat exchanger
indicator lamp on
• Are the “End” and “Anti-crease” indicator lamps lighting up? The drying cycle is
complete and the laundry can be taken out.
• If the drying result does not meet your expectation, select a drier programme or use
the dryness adjustment option (if available).
• Are thin and thick laundry mixed? Are different types of materials mixed? Sort the
laundry by thickness and material, then dry it again.
• Is the plug properly inserted into the mains electricity socket?
• Is there a power failure?
•Has the fuse blown?
• Is the door properly closed?
• Has a drying programme been selected?
•Has the
• Has the start delay option been selected?
• Is the dryer overloaded? Please remove some of the load.
• Is the lint filter clean?
• Is the water container empty?
• Has the water container been inserted correctly?
• Is the heat exchanger clean and inserted correctly?
“Start (Pause)”
button been pressed?
• Has the heat exchanger been inserted correctly?
Water droplets
underneath the dryer
• Has all lint on the heat exchanger seal and the door seal been wiped away?
• Has the water container been inserted correctly?
• If the direct drain connection is used, is it tight?
• Is the dryer levelled?
...you want to care for and clean your dryer:
Clean the filter at the end
of every cycle
Empty the water container
at the end of every drying
cycle
Clean the heat exchanger
at least once a month
• Brush lint using a soft brush or your fingertips.
• Close the filter.
• Push the filter back into place.
• Pull the handle to remove the water container.
• Empty the water container.
• Replace the empty water container by pushing it fully back into place.
• Clean the heat exchanger under running water.
• Remove all lint from the seals.
• Clean the heat exchanger housing (for further information see section “Cleaning the
heat exchanger” in the Instructions for Use).
3
Failure codes
In the event that the dryer malfunctions, one of the following failure codes may be displayed.
Depending on the model of your dryer, the failure may be displayed in letters or by different
blinking LEDs.
Failure code LED failure code Check to be carried out by customer before service call
F01
F02
F03
F04
F05
F06
Please call the After-Sales Service.
Please call the After-Sales Service.
Please call the After-Sales Service.
Please call the After-Sales Service.
Turn the dryer OFF and unplug it. Make sure that the ambient temperature is
between 5°C and 35°C. Wait for 1 hour. Plug the dryer back in and restart it. If the
failure reoccurs, please call the After-Sales Service.
Turn the dryer OFF and unplug it. Make sure that the ambient temperature is
between 5°C and 35°C. Wait for 1 hour. Plug the dryer back in and restart it. If the
failure reoccurs, please call the After-Sales Service.
F07
Start LED blinks
2 times per
second when
pressed
4
Please call the After-Sales Service.
Make sure that the door is correctly closed and the heat exchanger correctly positioned.
If the failure reoccurs, please call the After-Sales Service.
LED not blinking LED blinking
Before using the machine, please also read the Instructions For Use carefully!
GB
AZB 9750
Quick Reference Guide
Programme selector knob
The drying programme is selected by
turning this knob. The
indicator lamp flashes.
“Start (Pause)”
“Start (Pause)” button
The drying programme is started by
pressing this button. The indicator lamp
lights up.
Clean filter
The indicator lamp lights up when the
filter and/or the heat exchanger and its
housing need to be cleaned.
Clean the filter at the end of every
drying cycle.
Water container
The indicator lamp lights up when the
water container needs to be emptied.
The drying cycle is automatically
interrupted. Empty the container and
restart the drying programme.
Empty the water container after
every drying cycle
.
End of cycle
The drying programme is finished. Please
unload the dryer.
Indicator lamps
Overdry protection / 6th Sense
The indicator lights up when a humidity
controlled programme is selected, to
indicate the activated protection function.
Gentle
Selecting this option will reduce the
drying temperature. This option cannot
be selected when the “Rapid” option is
selected (if available).
Buzzer
When this option is pressed, a buzzer will
indicate the end of the drying cycle. This
option deactivates the “Anticrease”
function, if it is activated.
Start delay
Delays the start of the drying cycle by 3, 6
or 9 hours. Each time the button is
pressed the delay is increased by 3 hours.
Press the
confirm the final selection and to start the
dryer. The LEDs above the programme
selector knob flash to indicate the
selected time. During the countdown, the
drum will turn from time to time to
redistribute the laundry and the pump will
start to pump water in the water
container. To cancel or change the
previously set time delay, set the index of
the programme selector knob to the
“Off” position, or open the door.
“Start (Pause)”
button to
5019 307 01444
(Subject to technical modifications)
5
Loading...