Additional information (including troubleshooting and service) can be found in the individual sections of the
Instructions For Use.
Sort laundry according to
care symbols
Do not tumble dry
Suitable for tumble drying -
at low temperatures
Suitable for tumble drying
Prepare laundry
Load dryer
Select programme
Select options
(if available)
Start dryer
Sort laundry by:
Material thickness:
separate laundry according to weight (e.g. dry towels and thin underwear separately).
Type of material:
Dryness level:
Do not tumble dry:
metallic decorations, bulky items such as sleeping bags or pillows.
Check that all fastenings are closed and that pockets are empty. Ensure that there are
no cigarette lighters in the wash. Turn laundry inside out.
Place laundry loosely in the drum to achieve even drying throughout. Then close the
door.
Select the required drying programme by turning the programme selector knob (for
information, refer to programme table).
Select the required option by pressing the corresponding button.
The indicator lamp above the relevant button lights up to confirm your selection.
A fast blinking LED indicates that an invalid selection has been made (incompatible
option). Press the button again to cancel the option.
Start the drying programme by pressing the
The relevant indicator lamp lights up.
Changing programme selection:
drying, the dryer stops. The
To run the new programme, press the
Interrupting programme:
button and open the door. Wait at least 5 minutes, to allow the laundry to cool down,
before unloading the dryer. For your safety, the drying cycle stops automatically if you
open the door. To restart the cycle after opening the door, press the
button again.
Warning:
items are quickly removed and spread out so that the heat is dissipated.
never stop a tumble dryer before the end of the drying cycle, unless all
whenever the load is greater than the dryer can handle,
cotton (linen); synthetic textiles (easy care).
cupboard dry, iron dry etc.
woollens, silk, nylon stockings, delicate embroidery, fabrics with
“Start (Pause)”
if the selected programme is changed during
“Start (Pause)”
to interrupt a drying cycle, press the
indicator lamp flashes.
“Start (Pause)”
button.
button again.
“Start (Pause)”
“Start (Pause)”
The final part of a drying cycle occurs without heat (cool-down cycle) to ensure that
Programme end -
unload dryer
Switch dryer off
Set the programme selector knob to “Off” (“O”).
Cleaning the lint filter:
fingertips. Close lint filter and push firmly back into place (more detailed informations are given in the Instructions For Use).
Emptying the water container:
completely back into place.
Please note:
thoroughly in plenty of water before drying. Never dry rubber objects or objects stained with vegetable oils in the dryer.
The Manufacturer is not liable for any damage to laundry resulting from inadequate or incorrect fabric care instructions which
have been provided with the garment or article.
only use additives/plastic items specified as dryer safe and rinse items that have been treated with stain remover
open door, pull lint filter up and out of machine and open it. Brush lint using a soft brush or your
pull container out by the handle and empty. Replace the container when empty by pushing it
the items reach a lower temperature to avoid wrinkling.
take the laundry out of the dryer. The drying process is complete and the anti-
End:
crease phase has been reached (active).
Set the programme selector knob to “Off” (“O”).
1
Page 2
Approximate
Wet
80’
70’
65’
55’
30’
55’
25’
45’
20’
60’
30’
40’
50’
30’ 40’
60’ 90’
load
(in minutes)
drying times
Ver y
Start
delay
wet
Avvio
load
ritardato
95’
160’
185’
80’
140’
170’
75’
120’
140’
65’
100’
115’
40’
70’
40’
Buzzer
fine ciclo
Suoneria
Rapid
Rapido
Cotton
Antipiega
Anti-crease
Gentle
Gentile
*
kg
of load
Vol u me
Fabrics
Type of textile
3.0
XXXXX
7.0
XXXXX
3.0
7.0
3.0
coloured laundry
Cotton or linen hot wash/
XX105’90’
—
XXXXX
XXXXX
XX—XX
XX—XX
XX—XX
7.0
Max. 7 kg
3.0
7.0
1.0
Synthetic, mixed fibre or cotton
3.5
1.0
laundry
easy care (ironing not required)
3.5
1.0
Max. 3.5 kg
3.5
Laundry made from synthetic fibres
2.5XX
Max. 2.5 kg
3.0XX—XX85’70’
Cotton - Synthetic blend
————X———
Max. 3.0 kg
—XX—X—
All fabrics
2
Overview of programmesOptions
Programmes / Drying levels
Multi-layered, thick laundry such as: terry towels,
terry towelling bath robes.
Extra dry
Terry towels, dry towels, bed linen, underwear.
Similar types of laundry which do not require ironing
such as: dry towels, bed linen, underwear, baby
clothes, T-shirts, cotton socks.
Laundry which requires ironing such as: bed and
table linen, dry towels, T-shirts, polo shirts, work
clothes.
Laundry with thick, multi-layered areas such as: bed
and table linen, track suits, anoraks, blankets.
Laundry which does not require ironing such as:
shirts, blouses, T-shirts, sportswear.
Laundry which requires ironing such as: trousers,
dresses, skirts, shirts, blouses.
Cupboard dry +
Cupboard dry **
Iron dry **
Cupboard dry +
Cupboard dry **
Iron dry
Cotton
Easy care
Low drying intensity for delicates and items such as:
trousers, dresses, shirts, blouses.
Delicate plus
T-shirts, blouses, towels, underwear, sportswear.
Mixed load
Special programmes
All textiles.
Laundry is aired, refreshed and loosen
up for 30 minutes without heating.
Airing
Additional drying time for textiles that are not
suitable for other programmes, or for finalisation of
the drying process.
30’ 40’ 60’ 90’
times
Drying
Weight of average and maximum load.
Test programmes according to EN 61121, tested with maximum rated load capacity.
*
**
Page 3
How to proceed if...
...you want to check the dryer yourself first:
(If your machine is not functioning correctly, please
check the following points before calling the Customer Service department - also refer to relevant
section in the Instructions For Use).
• Was the inserted laundry too wet (washing machine spin speed less than 1000 rpm)?
• Is the lint filter dirty? (filter indicator light on)
• Is the heat exchanger dirty? (for more information, refer to the Instructions For Use)
• Is the room temperature too high?
Drying takes too long/
Laundry is not dry enough
The dryer does not
operate (after a power
failure, always press the
“Start (Pause)” button)
Lint filter, water container
or heat exchanger
indicator lamp on
• Are the “End” and “Anti-crease” indicator lamps lighting up? The drying cycle is
complete and the laundry can be taken out.
• If the drying result does not meet your expectation, select a drier programme or use
the dryness adjustment option (if available).
• Are thin and thick laundry mixed? Are different types of materials mixed? Sort the
laundry by thickness and material, then dry it again.
• Is the plug properly inserted into the mains electricity socket?
• Is there a power failure?
•Has the fuse blown?
• Is the door properly closed?
• Has a drying programme been selected?
•Has the
• Has the start delay option been selected?
• Is the dryer overloaded? Please remove some of the load.
• Is the lint filter clean?
• Is the water container empty?
• Has the water container been inserted correctly?
• Is the heat exchanger clean and inserted correctly?
“Start (Pause)”
button been pressed?
• Has the heat exchanger been inserted correctly?
Water droplets
underneath the dryer
• Has all lint on the heat exchanger seal and the door seal been wiped away?
• Has the water container been inserted correctly?
• If the direct drain connection is used, is it tight?
• Is the dryer levelled?
...you want to care for and clean your dryer:
Clean the filter at the end
of every cycle
Empty the water container
at the end of every drying
cycle
Clean the heat exchanger
at least once a month
• Brush lint using a soft brush or your fingertips.
• Close the filter.
• Push the filter back into place.
• Pull the handle to remove the water container.
• Empty the water container.
• Replace the empty water container by pushing it fully back into place.
• Clean the heat exchanger under running water.
• Remove all lint from the seals.
• Clean the heat exchanger housing (for further information see section “Cleaning the
heat exchanger” in the Instructions for Use).
3
Page 4
Failure codes
In the event that the dryer malfunctions, one of the following failure codes may be displayed.
Depending on the model of your dryer, the failure may be displayed in letters or by different
blinking LEDs.
Failure codeLED failure codeCheck to be carried out by customer before service call
F01
F02
F03
F04
F05
F06
F07
F10 - 15
F18
F19
F20
F21
F22
Start LED blinks
2 times per
second when
pressed
Heat exchanger
LED blinks 2
times when Start
button is pressed
Please call the After-Sales Service.
Please call the After-Sales Service.
Please call the After-Sales Service.
Please call the After-Sales Service.
Turn the dryer OFF and unplug it. Make sure that the ambient temperature is
between 5°C and 35°C. Wait for 1 hour. Plug the dryer back in and restart it. If the
failure reoccurs, please call the After-Sales Service.
Turn the dryer OFF and unplug it. Make sure that the ambient temperature is
between 5°C and 35°C. Wait for 1 hour. Plug the dryer back in and restart it. If the
failure reoccurs, please call the After-Sales Service.
Please call the After-Sales Service.
Turn the dryer OFF and unplug it. Wait for 5 minutes. Plug the dryer back in and restart it.
If the failure reoccurs, please call the After-Sales Service.
Turn the dryer OFF and unplug it. Wait for 1 hour. Plug the dryer back in and restart it.
If the failure reoccurs, please call the After-Sales Service.
Turn the dryer OFF and unplug it. Wait for 5 minutes. Plug the dryer back in and restart it.
If the failure reoccurs, please call the After-Sales Service.
Turn the dryer OFF and unplug it. Wait for 1 hour. Plug the dryer back in and restart it.
If the failure reoccurs, please call the After-Sales Service.
Turn the dryer OFF and unplug it. Wait for 5 minutes. Plug the dryer back in and restart it.
If the failure reoccurs, please call the After-Sales Service.
Turn the dryer OFF and unplug it. Wait for 5 minutes. Plug the dryer back in and restart it.
If the failure reoccurs, please call the After-Sales Service.
Make sure that the door is correctly closed and the heat exchanger correctly positioned.
If the failure reoccurs, please call the After-Sales Service.
Make sure that the heat exchanger is correctly positioned.
If the failure reoccurs, please call the After-Sales Service.
LED not blinking LED blinking
4
Page 5
Before using the machine, please also read the Instructions For Use carefully!
GB
AZB 7000
Quick Reference Guide
Programme selector knob
The drying programme is selected by
turning this knob. The
indicator lamp flashes.
“Start (Pause)”
“Start (Pause)” button
The drying programme is started by
pressing this button. The indicator lamp
lights up.
Filter
The indicator lamp lights up when the
filter and/or the heat exchanger and its
housing need to be cleaned.
Clean the filter at the end of every
drying cycle.
Water container
The indicator lamp lights up when the
water container needs to be emptied.
The drying cycle is automatically
interrupted. Empty the container and
restart the drying programme.
Empty the water container after
every drying cycle
.
Clean heat exchanger
The LED lights up after 30 cycles when the
heat exchanger needs to be cleaned. After
the heat exchanger has been cleaned, the
indicator lamp will switch off automatically
when the next drying cycle is started.
Indicator lamps
“Remaining time” display
Depending on the selected programme, a
default drying time is displayed. After the
start of the cycle, the displayed time is
corrected depending on the volume, type
and moisture level of the laundry.
The specified drying time is a
calculated value which will be
updated during the drying cycle.
The flashing lines indicate that the
calculation is in progress. The remaining
time will be updated.
End
The drying programme is finished. Please
unload the dryer.
Overdry protection / 6th Sense
The indicator lights up when a humidity
controlled programme is selected, to
indicate the activated protection function.
Key lock
For child safety, this option can be used to
lock all functions of the user interface.
To activate/deactivate this option, the
button must be pressed for 3 seconds.
The only remaining function available is
the “Off” position of the programme
selector knob.
The key lock function remains active even
when the selector knob is turned to the
“Off” position or the door is opened. The
function must be deactivated manually.
5
Page 6
Gentle
Selecting this option will reduce the
drying temperature. This option cannot
be selected when the “Rapid” option is
selected (if available).
Anti-crease
This option can be chosen to reduce
wrinkling, when the laundry is not
unloaded immediately after the end of the
cycle. The drum turns from time to time
for up to 12 hours. It can be interrupted
at any time by switching off the dryer. This
option deactivates the “Buzzer” function,
if it is activated.
Rapid Cotton
Selecting this option reduces the drying
time. This option should only be selected
for cotton programmes, with a maximum
load of 3.5 kg.
The garments should be a similar size and
thickness.
Buzzer
When this option is pressed, a buzzer will
indicate the end of the drying cycle. This
option deactivates the “Anti-crease”
function, if it is activated.
Start delay
Delays the start of the drying cycle by 1 to
12 hours. Each time the button is pressed,
the start time is delayed by 1 hour. Press
the
“Start (Pause)”
the final selection and to start the dryer.
The “:” in the window flashes and the
time is counted down in 1-hour intervals.
During the countdown, the drum will turn
from time to time to redistribute the
laundry and the pump will start to pump
water into the water container. To cancel
or change the previously set time delay,
set the index of the programme selector
knob to the “Off” position, or open the
door.
6
button to confirm
5019 307 01317
(Subject to technical modifications)
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.