CONTENTS
QUICK REFERENCE GUIDE
PROGRAMME CHART
PREPARING THE LAUNDRY
SELECTING A PROGRAMME AND OPTIONS
STARTING AND COMPLETING A PROGRAMME
CHANGING A PROGRAMME
INTERRUPTING A PROGRAMME
DAILY MAINTENANCE AND CLEANING
INSTRUCTIONS FOR USE
BOOKLET
BEFORE USING THE DRYER / CONNECTIONS |
PAGE 4 |
ELECTRICAL CONNECTION |
PAGE 5 |
PRECAUTIONS AND GENERAL RECOMMENDATIONS |
PAGE 6 |
DESCRIPTION OF THE DRYER |
PAGE 7 |
VENT CONNECTION |
PAGE 8 |
DOOR REVERSIBILITY |
PAGE 9 |
TROUBLESHOOTING GUIDE / AFTER-SALES SERVICE |
PAGE 10 |
3
BEFORE USING THE DRYER / CONNECTIONS
1. Removing the packaging and check
•After unpacking, make sure that the dryer is undamaged. If in doubt, do not use the dryer. Contact After-Sales Service or your local retailer.
•Keep the packaging materials (plastic bags, polystyrene parts, etc.) out of reach of children, as they are potentially dangerous.
2. Electrical Connections
•Electrical connections must be carried out by a qualified technician in compliance with the manufacturer’s instructions and current standard safety regulations.
•Electrical connection must comply with local Electricity Board regulations.
•Voltage information, power consumption and the required fuse protection is shown on the rating plate mounted at the rear of the dryer.
•The manufacturer cannot accept any liability for personal injury or damage to property resulting from failure to adhere to these instructions.
•The dryer must be earthed as prescribed by law.
•Do not use extension leads or multiple adaptors.
•Before any maintenance on the dryer disconnect it from the mains supply.
•Do not operate the dryer if it has been damaged during transport. Contact one of our After-Sales Service technicians.
•Mains cable replacement is only to be carried out by After-Sales Service.
•After installation access to the mains plug has to be guaranteed, or the all-pole disconnection has to be possible with a switch.
3.Installation
•Do not install your dryer where it can be subject to extreme conditions, such as: poor ventilation, temperatures around freezing (or above 35°C).
•Remove the protective foil from the control panel.
Stability:
When installing the dryer always carefully level the dryer adjusting the two feet and check the correct levelling with a spirit level.
To built in the dryer
•For security reasons do not remove the worktop.
•Connect the dryer to an external ventilation system in order to prevent steam from damaging your furniture during the years.
Stacking kit
Your dryer can be stacked on top of your front loading washing machine. To do this, use stacking kit AMH 542, available at your dealer.
Minimum housing dimensions:
Width: 600 mm
Height: 850 mm
Depth: 560 mm
4
ELECTRICAL CONNECTION
1) For Great Britain only
Warning - this appliance must be earthed
Fuse replacement
If the mains lead of this appliance is fitted with a BS 1363A 13amp fused plug, to change a fuse in this type of plug use an A.S.T.A. approved fuse to BS 1362 type and proceed as follows:
1.Remove the fuse cover (A) and fuse (B).
2.Fit replacement 13A fuse into fuse cover.
3.Refit both into plug.
Important:
The fuse cover must be refitted when changing a fuse and if the fuse cover is lost the plug must not be used until a correct replacement is fitted.
Correct replacement are identified by the colour insert or the colour embossed in words on the base of the plug.
Replacement fuse covers are available from your local electrical store.
2) For the Republic of Ireland only
The information given in respect of Great Britain will frequently apply, but a third type of plug and socket is also used, the 2-pin, side earth type.
3) Socket outlet / plug (valid for both countries)
If the fitted plug is not suitable for your socket outlet, please contact Whirlpool Service for further instruction. Please do not attempt to change plug yourself. This procedure needs to be carried out by a qualified Whirlpool technician in compliance with the manufactures instructions and current standard safety regulations.
5
Loading...