Whirlpool AWM 020 INSTRUCTION FOR USE

GB
AWM 020
PROGRAMME GUIDE
Indicator:
Water Stop
Door lock
h
Start preselection
min
Time remaining
(if available)
Programme Care label Type of fabric /
Cotton
Cotton
Easy Care
Delicates
Wool
Rinse + Spin
Gentle Spin 5
Drain
*) Appliance with max. spin speed greater than 900 rpm: To protect the wash, the real spin speed is here reduced to 900 rpm. **) The Programme Duration indicated is an approximate value for a programme with maximum tempe rature but without special options.
Degree of soiling
Slightly to normally soiled bed linen, table linen, underwear, towels, shirts etc. made of cotton and linen
Slightly to normally soiled bed linen, table linen, underwear, towels, shirts etc. made of cotton and linen
Slightly to normally soiled blouses, shirts, overalls etc. made of polyester (Diolen, Trevira), polyamide (Perlon, Nylon) or blends with cotton
Curtains, delicate dresses, skirts, shirts and blouses
Only woollens with a felt-free finish, labelled with the woolmark and identified as machine washable
—5
Max. Load
Kg
Normal 5,0
Quick
Wash 3,0
Normal 5,0
Quick
Wash 3,0
Normal 2,5
Quick
Wash 1,5
1,5
1
Detregent and
Additives
Sof-
tener
Selectable special options =
Main
Wash
Pre-
wash
yes
yes
yes
yes
yes
—— — —
❉❉ ❉
❉❉ ❉❉❉❉❉❉
❉❉ ❉❉❉❉❉
❉❉
❉❉
Start
preselection
h
Energy
save
Quick Wash
max °60
—— —
—— —
Intensive
Rinse
❉❉❉❉
❉❉
Rinse
Hold
Pre-
wash
❉❉
❉❉
Spin
*)
*)
*)
*)
Programme
Selector
Cotton
95°
Cotton
60°, 40°, 30°
Easy Care
60°,50°,
40°, 30°
Delicates
40°, 30°
Wool
40°
Rinse +
Spin
+
Gentle Spin
gramme
Duration
approx.
Quick
Wash: 60
Quick
Wash: 60
Quick
Wash: 40
Indicator:
Pro-
**)
min.
115
110
80
45
35
For heavily soiled washing, Prewash can be selected in addition. If “Quick Wash” is selected, the “Energy save” special option cannot be selected.
For heavily soiled washing, Prewash can be selected in addition. If “Quick Wash” is selected, the “Energy save” special option cannot be selected.
If “Quick Wash” is selected, the “Energy save” special option cannot be selected.
If you select “Rinse Hold”, do not leave the wash in the rinsing water for too long.
Programme for treating wash with starch or softener. Subsequent spinning is intensive. Same as the spin programme in the Coloured Wash programme.
Gentle Spin can be used in this programme. Same as the spin cycle in the Wool programme.
Empt only - do not spin. Alternative way of terminating programmes after “Rinse Hold”.
Notes
5019 100 03560
Power and water consumption data
GB
Programme Temperature
Cotton 95 5 Cotton 95 5 Energy save 49 1,10 120 Cotton 60 5 Energy save 49 0,95 125 Cotton 60 5 Cotton 60 2,5 Cotton 40 5
Cotton 30 3 Quick Wash 32 0,25 45 Easy Care 60 2,5 Easy Care 40 2,5 Easy Care 30 1,5 Quick Wash 36 0,20 35
Delicates 40 1,5
Wool 40 1
Prewash cycle increases programme duration by approx. 15 minutes. Consumption data were measured in normali sed conditions in compliance with Standard IE C 60456. The data on the energy label refers to the Cotton 60°C” programme when using the Energy save special option. Consumption values in the home may vary with respect to the values in the table depending on the water pressure, the water supply temperature, the load and the type of wash. *) The Time remaining indicator (if available) may also vary from the values in the table, since the particular house­hold conditions are taken into account by the Time remaining indicator.
Selector
(°C) (kg) (l) (kWh) (Min.)
Max. Load Special
Option
— — —
— —
— —
Water Energy Programme
57 1,70 115
49 1,10 110 38 0,90 105 49 0,55 95
59 0,70 90 53 0,50 80
55 0,50 50 55 0,50 40
Duration *)
FOR DAILY USE:
1. Turn on the water supply tap.
2. Sort and load the laundry by fabric type and colour.
3. Close the door.
4. Add detergent and additives.
5. Select the programme, the temperature and special options.
6. The light above the “Start” button flashes. Press the “Start” button for about one second.
NOTE:
During the first 15 minutes of Cotton and Easy Care programmes (each without Prewash) you can open the door to add items to the wash. This is not possible with Quick Wash”.
CHANGING A PROGRAMME:
a) SELECT NEW PROGRAMME AND CONTINUE
1.Select new programme.
2.The light above the “Start” button flashes. Press the “Start” button for about one sec­ond. The new programme will continue from the same programme step where the running
programme was interrupted.
b) TO CANCEL A PROGRAMME THAT IS ALREADY RUNNING AND START A NEW PROGRAMME
There's no need to add more detergent when you start the new programme, because no water is drained out when you cancel the programme.
1.Hold down the “Start” button for five seconds, or until the programme control audibly restarts and the time remaining indicator shows “0”.
2.Wait until the programme sequence indicator returns to the left.
3.Set the programme selector to “0”.
4.Set the programme selector to the new programme, and select any new special options you require.
5.The light above the “Start” button flashes. Press the “Start” button for about one second.
TO INTERRUPT THE PROGRAMME - PAUSE:
To interrupt the running programme for a certain period and continue it at a later time:
1. Set the programme selector to “0”.
2. Set the programme again after the desired pause.
3. Press the “Start” button for about one minute.
TROUBLESHOOTING GUIDE:
Your washing machine is equipped with automatic safety functions for the early detection and indication of any possible faults, and for reacting appropriately. Often these are no more than minor problems that can be solved quickly. Examples of these are:
The appliance fails to start.
Aftertreatment agents not fully washed in.
The appliance vibrates during the spin cycle.
Load not completely spun at the end of the programme.
Advice on these points can be found in the instructions for use in the “Troubleshooting Guide section. What to do if the washing machine safety system detects a fault.
The programme is interrupted and the various indicators show the fault:
INDICATOR LIGHTS FLASH DIGITAL DISPLAY
Start and Water Stop Time remaining
“Speed”, “Water Stop”,
Time remaining”, “Start preselection
“Speed”, “Water Stop”,
Time remaining”, “Start preselection
“Speed”, “Time Remaining”,
Start preselection flash
For appliances with Water Stop:
“Speed”, “Water Stop”,
Time remaining”, “Startpreselection
E4 or E5 or E6 or E7 or E8 or E9 Fault in an electrical Component
(if available)
(a number between 15 and 99)
E1 Fault in water supply
E3 Fault when draining
E2 Water Stop fault
WHAT TO DO?
Proceed as per the instructions in
the following section...
Fault in water supply
Loading...