Whirlpool AWE 2237 INSTRUCTION FOR USE

GB AWE 2237	PROGRAMME CHART
A. Programme selector		B
B. Programme sequence indicator
G		E
H		F
C. “Start/Pause” button		D
D. “Reset” button
E. “Door open” indication
	A	C

This washing machine is equipped with automatic safety functions which detect and diagnose faults at an early stage and react appropriately:

F.“Service” indication

G.“Water tap closed” indication

H.“Clean pump” indication

1)Do not use liquid detergent.

2)For improved garment care, spin speed is restricted to 400 rpm in this programme.

				Max.	Type of wash / Notes	Detergents and Additives			Special options		Max.
			Care	Load		Prewash	Main	Softener	Cold	No	Spin
Programme							Wash		wash	Spin	Speed
			Labels
									Lavado	Exclusión
					- for temperature selection, respect the manufacturer's recommendations on the care label
				kg					en frío	centrif.	rpm
Cotton with prewash		Algodón		5.0	Heavily soiled whites such as bed linen, table linen, underwear and towels made of cotton and	Yes 1)	Yes	i	–	i	800
95 °C		95°C			linen.
Cotton		Algodón		5.0	Normally to heavily soiled bed linen, table linen and underwear, towels, shirts etc. made of	–	Yes	i	i	i	800
40 - 60 - 95 °C		40 - 60 - 95°C			cotton and linen.
Synthetics with prewash		Sintéticos		2.5	Heavily soiled blouses, shirts, overalls etc. made of polyester (Diolen, Trevira), polyamide (Perlon,	Yes 1)	Yes	i	–	i	800
60 °C		60°C			Nylon) or blends with cotton.
Synthetics		Sintéticos		2.5	Normally soiled blouses, shirts, overalls etc. made of polyester (Diolen, Trevira), polyamide	–	Yes	i	i	i	800
30 - 40 - 60 °C		30 - 40 - 60°C			(Perlon, Nylon) or blends with cotton.
Delicates		Delicados		1.5	Curtains and delicate clothing, dresses, skirts, shirts and blouses.	–	Yes	i	i	i	800
30 °C		30°C
Quick wash		Rápido		3.0	Shortly worn outer clothing made of cotton, polyester, polyamide and blends with cotton.	–	Yes	i	i	i	800
30 °C		30°C
Wool		Lana		1.0	Only woollens with a felt-free finish, labelled with the woolmark and identified as machine	–	Yes	i	i	i	800
Cold - 40 °C		Frío - 40°C			washable.
Handwash		A mano		1.0	Textiles made of linen, silk, wool and viscose marked as “handwashable”.	–	Yes	i	i	i	400 2)
30 - 40 °C		30 - 40°C
Rinse & Spin		Aclarar y Centrif.	–	5.0	Same as the last rinse and the final spin in the “Cotton” programme.	–	–	i	–	i	800
Spin		Centrif. Intensivo	–	5.0	In this programme spinning is intensive. Same as the spin cycle in the “Cotton” programme.	–	–	–	–	i	800
Gentle Spin		Centrif. Suave	–	1.0	In this programme spinning is gentle. Same as the spin cycle in the “Wool” programme.	–	–	–	–	i	800
Drain		Desagüe	–	–	Drain only - no spinning.	–	–	–	–	–	–

N.B. This machine is controlled by sensors. Please avoid excessive detergent dosing.

Whirlpool is a registered trademark of Whirlpool USA.

5019 312 10624

CONSUMPTION DATA

	Temperature	Load	Water	Energy	Approx. Programme
Programme					Duration
	(°C)	(kg)	(l)	(kWh)	(hours : minutes)
Cotton	95	5.0	50*	1.70	2:05
Cotton**	60	5.0	45	0.85	2:30
Cotton	40	5.0	55	0.55	2:00
Synthetics	60	2.5	50*	0.80	1:30
Synthetics	40	2.5	45	0.45	1:15
Delicates	40	1.5	50	0.55	0:45
Quick wash	30	3.0	35	0.40	0:30
Wool	40	1.0	55	0.55	0:45
Handwash	40	1.0	40	0.40	0:35

Prewash cycle increases programme duration by aproximately 20 min. Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.

*To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.

** Reference Programme for Energy Label.

PREPARATION OF THE WASH CYCLE

1.Load the machine, close the drum doors and check that they are properly locked.

2.Add detergent and additives into the dispenser to no more than the “MAX” level mark, as follows:

• Programme with pre and main wash

• Main wash programme without prewash

• Fabric softeners and conditioners

•Stain remover agents

•Anti-scale agents (if necessary) 3. Close the lid.

4. Turn the programme selector to the desired programme and temperature. The lamp next to the “Start/Pause” button flashes.

SELECT THE DESIRED OPTION(S)

Selecting or deselecting an option can be done at any time during the programme. The option will be applied as long as the corresponding programme phase has not been executed yet.

“Cold wash” button

•Water is heated only up to 20°C.

•Suitable for delicate laundry items with wash temperature recommendation of max. 30°C on the care label.

•Selectable only on the lowest temperature step of each programme.

“No Spin” button

•Especially for delicate garments to avoid wear and tear caused by the spin.

Note: with the “Cotton” and “Synthetics” programmes, a short spin cycle is provided in any case, even if the “no spin” option has been selected, in order to optimize rinsing results.

PROGRAMME START

Open the tap and press the “Start/Pause” button. The indication lamp next to the “Start/Pause” button lights up. The programme sequence indicator shows the current programme phase, running from left to right through Wash, Rinse, Spin/Drain. When the programme phrase is finised, the corresponding indication goes out.

•Note: If there is a power interruption or if the appliance is disconnected during the cycle, the programme will run again from the point where it was interrupted.

“DOOR OPEN” INDICATION

Before starting and after end of a programme, the lamp lights to show the the lid can be opened. As long as a wash programme is running, the lid remains locked and must on no account be forced open. In case you have an urgent need to open it during a running programme, refer to “Cancel (Reset) a running programme before the end”.

RED INDICATIONS

“Service”

Lighting up of the “Service” indication can be caused by a fault in an electrical component. Refer to the “Troubleshooting Guide” in your “Instructions for Use”; if the fault persists, contact our After Sales Service.

“Water tap closed”

The appliance has no or insufficient water supply. Open the water tap: if the indications still lights up, refer to the “Troubleshooting Guide” in the Instructions for Use.

“Clean pump”

Waste water is not pumped out. Check whether the drain hose is kinked or the filter must be cleaned: in the latter case refer to the Instructions for Use (“Removing the Filter”).

PROGRAMME END

•All the lights of the programme sequence indicator are off, and the “Door open” indication lights up.

1.Turn the programme selector to the “Off/O” position.

2.Close the water tap.

3.Open lid and drum and unload the machine.

4.Leave the lid open for some time to allow the interior of the machine to dry.

CHANGE PROGRAMME AND/OR OPTIONS AFTER PROGRAMME START

1.Press the “Start/Pause” button to pause the programme. The light flashes.

2.Select the new programme, any options and another spin speed if you want.

3.Press the “Start/Pause” button again. The new programme continues at the same position where the previous programme was interrupted. Do not add detergent for this programme.

CANCEL (RESET) A RUNNING PROGRAMME BEFORE THE END

The “Reset” button cancels a programme before the end. Press the “Reset” button for at least 3 seconds. Any existing water is drained out before the door can be opened.

Whirlpool is a registered trademark of Whirlpool USA.

5019 312 10624