GB
Design Series Traditional Series 800 Traditional Series 700
BAIN-MARIE UNITS AND
HEATED GLASS TOPS
ASE 549 |
ASE 573 |
ASE 597 |
ASE 621 |
ASE 346 |
ASE 031 |
ASE 550 |
ASE 574 |
ASE 598 |
ASE 622 |
ASE 347 |
ASE 032 |
ASE 551 |
ASE 575 |
ASE 599 |
ASE 324 |
ASE 348 |
ASE 033 |
ASE 552 |
ASE 576 |
ASE 600 |
ASE 325 |
ASE 349 |
ASE 034 |
ASE 553 |
ASE 577 |
ASE 601 |
ASE 326 |
ASE 350 |
ASE 035 |
ASE 554 |
ASE 578 |
ASE 602 |
ASE 327 |
ASE 351 |
ASE 036 |
ASE 555 |
ASE 579 |
ASE 603 |
ASE 328 |
ASE 352 |
ASE 037 |
ASE 556 |
ASE 580 |
ASE 604 |
ASE 329 |
ASE 353 |
ASE 038 |
ASE 557 |
ASE 581 |
ASE 605 |
ASE 330 |
ASE 354 |
ASE 039 |
ASE 558 |
ASE 582 |
ASE 606 |
ASE 331 |
ASE 355 |
ASE 040 |
ASE 559 |
ASE 583 |
ASE 607 |
ASE 332 |
ASE 356 |
ASE 041 |
ASE 560 |
ASE 584 |
ASE 608 |
ASE 333 |
ASE 357 |
ASE 042 |
ASE 561 |
ASE 585 |
ASE 609 |
ASE 334 |
ASE 358 |
ASE 043 |
ASE 562 |
ASE 586 |
ASE 610 |
ASE 335 |
ASE 359 |
ASE 044 |
ASE 563 |
ASE 587 |
ASE 611 |
ASE 336 |
ASE 360 |
ASE 045 |
ASE 564 |
ASE 588 |
ASE 612 |
ASE 337 |
ASE 022 |
ASE 046 |
ASE 565 |
ASE 589 |
ASE 613 |
ASE 338 |
ASE 023 |
ASE 047 |
ASE 566 |
ASE 590 |
ASE 614 |
ASE 339 |
ASE 024 |
ASE 048 |
ASE 567 |
ASE 591 |
ASE 615 |
ASE 340 |
ASE 025 |
ASE 049 |
ASE 568 |
ASE 592 |
ASE 616 |
ASE 341 |
ASE 026 |
|
ASE 569 |
ASE 593 |
ASE 617 |
ASE 342 |
ASE 027 |
|
ASE 570 |
ASE 594 |
ASE 618 |
ASE 343 |
ASE 028 |
|
ASE 571 |
ASE 595 |
ASE 619 |
ASE 344 |
ASE 029 |
|
ASE 572 |
ASE 596 |
ASE 620 |
ASE 345 |
ASE 030 |
|
INSTRUCTIONS FOR INSTALLING AND
USING THE BAIN MARIE UNITS AND HEATED GLASS TOPS THESE APPLIANCES CONFORM TO THE FOLLOWING DIRECTIVES:
73/23 EEC: LOW VOLTAGE, ELECTRICAL SAFETY 89/336 EEC: ELECTROMAGNETIC COMPATIBILITY
93/68 EEC: EC MARKING REGULATIONS
Ed: A |
Data |
Evento modifica |
Redatto |
Verificato |
Approvato |
Rev: Ø |
01.01.2002 |
Prima emissione |
- |
- |
- |
Rev: 1 |
30.06.2005 |
Revisione Lay-Out |
RSSC |
ULGR |
TNPL |
Rev: 2 |
|
|
|
|
|
SUMMARY
1. |
GENERAL WARNINGS |
pg.3 |
2. |
SPECIAL WARNINGS FOR POSITIONING AND WIRING THE APPLIANCE |
pg.3 |
3. |
POSITIONING |
pg.4 |
4. |
LEGAL PROVISIONS AND DIRECTIVES |
pg.4 |
5. |
ELECTRICAL AND EQUIPOTENTIAL WIRING |
pg.4 |
6. |
WATER CONNECTIONS |
pg.5 |
7. |
GENERAL OPERATING INSTRUCTIONS |
pg.5 |
8. |
CLEANING AND CARE |
pg.6 |
9. |
CONTROL PANEL |
pg.6 |
10.USE AND FUNCTIONS |
pg.7 |
The manufacturer declines all responsibility for any printing or copying errors in this handbook.
The manufacturer reserves the right to make any changes deemed necessary or useful to its products without altering the basic features.
All rights reserved. No part of this publication may be reproduced or photocopied without prior permission from the manufacturer.
2
1. GENERAL WARNINGS
Only qualified installers and staff authorised by the manufacturer may perform the installation, start-up and maintenance work to the appliance.
Read these instructions carefully beforehand, as they are very important for safety when installing, using and servicing the appliance.
1.The appliance must only be used in the manner it was designed for, i.e. keeping previously cooked dishes hot; any other use does not conform to its design and is therefore strictly forbidden.
2.The ideal working conditions for the appliance are a temperature of 25°C with a humidity level of 60%.
3.After unpacking the appliance, ascertain that no damage has been caused during transport.
4.Before positioning and installing the appliance, check that the output and voltage features given on the data plate correspond to the power supply in the installation site.
The data plate is on the bottom right of the serving side.
5.In the event of problems, immediately turn the machine off and disconnect or close all connections.
2. SPECIAL WARNINGS FOR POSITIONING AND WIRING THE APPLIANCE
As prescribed by law, a multiple-pole switch must be installed between the appliance and the main power supply, with a contact opening of at least 3 mm per pole. The ground wire must not be disconnected. A water cut-off valve must be installed upstream from the bain-marie units; we recommend using only softened water. The appliance may be connected to the hot water line, to reduce the time required to reach the operating temperature.
3