Whirlpool AKP 765/01 IX, AKP 766 WH, AKP 764 AV, AKP 767 IX, OBU 227 S User Manual
...
54804-gb.fm5 Page 12 Thursday, April 5, 2001 6:04 PM
GB TABLE OF CONTENTS
INSTALLATION
ELECTRICAL CONNECTION
BEFORE USING THE OVEN
PROTECTING THE ENVIRONMENT
PRECAUTIONS AND GENERAL
RECOMMENDATIONS
OVEN ACCESSORIES
COOKING CHART
CLEANING THE OVEN AND ITS ACCESSORIES
TROUBLESHOOTING GUIDE
PAGE
PAGE
PAGE
PAGE
PAGE
PAGE
PAGE
PAGE
PAGE
13
14
15
15
15
16
17
18
19
AFTER-SALES SERVICE
12
PAGE
20
54804-gb.fm5 Page 13 Thursday, April 5, 2001 6:04 PM
INSTALLATION
Technical information for the installer
•
After removing the oven from its packaging,
before making the connections place it on the
polystyrene foam base to protect it from
damage.
•
Do not attempt to lift the oven by the handle.
Lift at the sides as shown in the figure
(see arrow).
•
Check that the appliance has not been
damaged in transit.
•
Oven dimensions and kitchen unit
dimensions are shown in the opposite figure.
•
For installation of the cooking hob, refer to
the product description sheet.
•
Kitchen units in contact with the oven must
be heat resistant (80° C min).
•
Carry out the electrical connections between
cooktop and oven (see chapter “Electrical
Connection”).
•
Install the oven in the housing, lifting it at the
sides, taking care not to trap the wires of the
electrical supply cable.
•
For correct ventilation, follow the ventilation
opening directions shown in the figure
(at least 500 x 80 mm or an equivalent area).
Also provide for at least 5 mm clearance
between the top of the oven and the lower
edge of the worktop. This space must not be
obstructed by cross rails or other structural
elements.
•
During oven installation, care must be taken
to ensure that the sides are not touching the
front edges of the housing or adjacent
drawers and doors (see picture).
No contacts
•
Secure the oven to the kitchen unit with
screws (A) as shown.
13
54804-gb.fm5 Page 14 Thursday, April 5, 2001 6:04 PM
INSTALLATION
• Warning: Do not connect to the power
supply before you have finished
connecting the oven and the cooktop.
• Make sure the oven is installed and
connected to the electricity supply by a
qualified technician in accordance with
the manufacturer’s instructions and in
compliance with local regulations.
• The installer is responsible for the correct
electrical connection of the oven and the
observance of the relative safety
prescriptions.
• The oven must be connected to the
electricity supply by means of an all-pole
disconnect switch with minimum contact
gap of 3 mm.
• The appliances must be earthed by law.
• Do not use multiple plug adapters or
extension leads.
• After the oven has been installed, the
electrical components must be
inaccessible.
ELECTRICAL CONNECTION
See separate installation instructions supplied with the cooktop.
Electrical connection between different
models of hobs and oven
Attention:
section of the oven, seen from the top, with the
observer standing in front of the oven door.
•
•
The figures represent the right hand
Put clamp “B” into the first holes of junction
block “C” starting from the left (as shown).
Connect the earth wire (D) of the cooktop to
the oven (E) as illustrated.
B
C
B
C
• Mount the corresponding knobs in the
control panel last
4 gas burners hob: position of the knobs in the
front controls hob
Glass ceramic hob: position of the knobs in the
front controls hob
B
C
3 gas burners/1 electric hot plate hob: position of
the knobs in the front controls hob
Glass ceramic hob (with 2 double cooking zones):
position of the knobs in the front controls hob
14
Loading...