Quick reference guide |
|
Chart |
(see at right for options description)
PROGRAM SELECTION |
|
START/RESUME BUTTON |
|
CANCEL/OFF BUTTON |
BUTTON |
|
Push this button to start the selected program: the |
|
Push this button to switch off the control panel. |
Push “P” button (repeatedly) |
|
indicator lights up and goes off at the end of the |
|
If pressed when a program is running it cancels the |
until selected program number |
|
program. |
|
program ongoing draining water for 1 minute |
is shown on the display |
|
When the door is opened during a washing cycle, |
|
(0:01 is shown into the display). |
(P1...Px) - see “Table of |
|
the cycle is temporarily paused: the Start indicator |
|
If pressed when the dishwasher is switched off, |
programs” below. |
|
blinks. To resume the cycle close the door and |
|
it drains any possible liquids from dishwasher |
|
|
push Start button again. |
|
(1 minute process). |
|
|
|
|
|
|
|
Table of programs |
|
Deter- |
|
Consumption |
Drying |
|||
|
Programs |
|
Available |
Loading instructions |
gent |
Litres |
kWh |
Minutes 1) |
Phase |
|
|
|
|
|
|||||||
|
|
|
options |
|
|
|
|
|
|
|
P1 |
Sensor |
40°-70°C |
Delay |
Recommended program for |
|
|
|
|
|
|
routine washes, with dried-on food |
X |
7-14 |
1.00-1.65 |
80-165 |
Full |
|||||
Half Load |
||||||||||
|
|
|
(e.g. EN 50242) |
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
P2 |
Pre-Wash |
cold |
Delay |
Crockery to be washed later. |
— |
4.0 |
0.03 |
14 |
NO |
|
|
|
|
|
|
|
|
|
|
|
|
P3 |
Fragile |
40°C |
Delay |
Light soiling, for example glasses |
X |
10.0 |
0.85 |
100 |
Light |
|
and cups. |
||||||||||
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
P4 |
Rapid |
45°C |
Delay |
Lightly soiled crockery, with no |
X |
11.0 |
0.80 |
30 |
NO |
|
dried-on food. |
||||||||||
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
P5 |
Eco 2) |
50°C |
Delay |
Normally soiled crockery. |
X |
6.0 |
1.03 |
170 |
Full |
|
|
Half Load |
Energy-saving program. |
||||||||
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
P6 |
Fast Daily |
60°C |
Delay |
Normally soiled crockery. |
X |
10.0 |
1.30 |
80 |
Full |
|
Half Load |
||||||||||
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
P7 |
|
|
|
Program including steam action |
|
|
|
|
|
|
Steam |
|
|
dedicated for heavily soiled |
|
|
|
|
|
||
|
|
Delay |
crockery, pots and pans. Soaking or |
X |
10.0 |
1.70 |
180 |
Full |
||
|
|
|
|
hand pretreatment is no longer |
|
|
|
|
|
|
|
|
|
|
needed. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Normally or heavily soiled crockery, |
|
|
|
|
|
|
P8 |
Hygiene 3) |
|
|
with additional antibacterial wash. |
|
|
|
|
|
|
|
Delay |
Program interruption (e.g. due to |
X |
13.0 |
1.50 |
118 |
Full |
|||
|
|
|
|
door opening) can compromise |
|
|
|
|
|
|
|
|
|
|
elimination of germs. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1)Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional options) and may vary depending on conditions. Differences of up to 20 minutes are possible with sensor programs as a result of the appliance’s automatic calibration system.
2)Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the EN/Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.
3)The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001. RECYCLING WATER SYSTEM: these programs save water in a dedicated tank.
A TANK CLEANING CYCLE (at least 45 min.) is automatically run every 30 cycles or after every power off, to assure the best product conditions.
BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!
THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING ANY
BUTTON EXCEPT CANCEL/OFF BUTTON.
FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.
Options and display description
SALT INDICATOR |
|
|
|
RINSE AID INDICATOR |
When lit (at the end of the cycle), |
|
|
|
When lit (at the end of the cycle), |
|
|
|
||
the salt reservoir needs to be |
|
|
|
the rinse aid dispenser needs to |
refilled. |
|
|
|
be refilled. |
|
|
|
||
|
|
|
|
|
WASH TIME DISPLAY
Indicated the cycle duration and the remaining time (h:min). With “Delayed start” selected it indicates the time remaining until program start (h.00) - below 1h (0:min).
If “Fx Ey” messages appears on the display, see page 6 - chapter “What to do if...”.
HALF LOAD BUTTON |
TABLET SETTING |
DELAYED START BUTTON |
Half load cycle can be used |
This setting allows to optimize |
Push the button (repeatedly) |
for the upper or lower rack. |
the cycle performances |
to delay the start of the |
Select the required program |
according the type of |
program. Adjustable from |
then press the “Half Load” |
detergent used. Push the |
1 to 24 hours. With each |
button - the light comes on. |
Tablet button for 3 seconds |
press of the button, the |
Turns off at the end of the |
(until the indicator lights up) |
delayed start indicator |
program. |
if you are using the combined |
increases by one hour and |
The “Half Load” option can |
detergents in tablet (rinse aid, |
after 24 restarts from 0. |
be used with the programs |
salt and detergent in 1 dose). |
Then press the START |
indicated in the table of |
If you are using powder |
button. The dishwasher will |
programs. |
detergent or liquid detergent, |
start after the set time. |
|
the Tablet indicator on the |
|
|
control panel has to be off. |
|
|
|
|
5019 396 03713
GB -1-
How to set water hardness in order to always assure the best cleaning results |
First time use |
10 |
4 |
|
9 |
||
|
||
1 |
|
3 2
5 |
6 |
7 |
8 |
1- salt reservoir
2- rinse aid dispenser
3- detergent dispenser
4- racks system
5,6,7,8- available functions on the panel
9- filters
10spray arms
Water hardness should be set only before the first wash or if water hardness has been changed
Water hardness level is factory set for medium-hard water (level 4).
Even if you use tablets which include salt functionality, you must still add regeneration salt since such detergents are not effective enough at softening hard water.
At first time use, the salt reservoir has to be filled independently from water hardness level (see description below in step 1 “Daily check”).
-Press and hold together PROGRAM Selection and CANCEL/Off buttons for minimum 3 seconds.
-The current water hardness setting will be visible on the display.
-Press the PROGRAM Selection button to increase setting. Value range goes from 1 to 7 (when the level reaches 7, the next press of the start button will set the level back to 1).
-Wait 30 seconds (control panel switches off) or press Start/Resume button to save setting.
1. Ask your water supply company what the water hardness is... |
2. ...enter this value on |
Suggestions for detergent use |
|||||||
|
|
|
|
|
|
your dishwasher |
|||
|
|
|
|
|
|
|
|
||
German |
French |
English |
Water hardness |
Insert value is shown |
Gel or Powder |
Tablets |
|||
degrees °dH |
degrees °fH |
degrees °eH |
level |
in the display |
(rinse aid and salt) |
||||
|
|||||||||
0 |
- 5 |
0 |
- 9 |
0 - 6.3 |
Soft |
1 |
|
|
|
|
|
|
|
|
|
|
|
||
6 - 10 |
10 |
- 18 |
7 - 12.6 |
Medium |
2 |
|
|
||
|
|
|
|
|
|
|
|
|
|
11 |
- 15 |
19 |
- 27 |
13.3 - 18.9 |
Average |
3 |
go to step 1 |
|
|
|
|
|
|
|
|
|
|
||
16 |
- 21 |
28 |
- 37 |
19.6 - 25.9 |
Medium-hard |
4 |
(see “Daily |
if water is |
|
|
|
|
|
|
|
|
check”) |
||
22 |
- 28 |
38 |
- 50 |
26.6 - 35 |
Hard |
5 |
HARD extra salt |
||
|
|||||||||
|
|
|
|
|
|
|
|
needs to be added |
|
29 |
- 35 |
51 |
- 63 |
35.7 - 44.1 |
Very hard |
6 |
|
||
|
(go to step 1, |
||||||||
|
|
|
|
|
|
|
|
“Daily check”) |
|
36 |
- 50 |
64 |
- 90 |
44.8 - 62.4 |
Extremely hard |
7 |
|
||
|
|
||||||||
|
|
|
|
|
|
|
|
|
Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!) |
Daily check |
||
1 |
Visual indicator |
|
Screw on the cap. |
(depending |
|
Salt residual |
|
on the model). |
|
around the cap |
|
|
Unscrew cap. |
|
need to be |
|
|
|
removed. Some |
|
|
|
salt reservoir have |
|
|
|
a level indicator |
|
|
|
integrated in the |
|
|
|
cap (see below |
|
|
|
how to check). |
|
Fill the salt reservoir with water |
Add salt (never add detergent!) |
|
|
before the first wash only. |
min. 0.8 kg / max. 1 kg |
|
Once regeneration salt is added, immediately start a wash program (the “Pre-wash” program alone is not sufficient).
Residual saline solution or grains of salt can lead to deep-down corrosion, irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such circumstances.
The salt level indicator lamp may remain lit at the end of several wash cycles. If the water hardness level falls within category (soft), no salt is required.
(depending on the model)
Salt indicator on the control panel
The indicator lamp lights up when SALT
NEEDS TO BE ADDED.
Salt indicator on the salt reservoir cap
green: OK. |
clear: NEEDS TO |
|
BE ADDED |
||
|
GB -2-
Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator |
Daily check |
2 |
Visual |
|
indicator |
If required, open the cover B (press the dedicated button).
(depending on the model)
Add rinse aid to the max. line ~150 ml
The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4).
Press the button to open the cover B. Using a coin or similar object, turn the arrow to the desired setting. After adjusting the rinse aid setting, shut the cover again.
Check the rinse aid indicator to check the level |
Rinse aid indicator on the control panel |
Rinse aid indicator on the dispenser |
|
into the dispenser. |
The indicator lamp lights up when RINSE AID NEEDS |
dark: OK. |
clear: NEEDS TO BE ADDED |
|
TO BE ADDED. |
||
|
|
|
|
|
|
|
|
Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the appliance.
If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is not perfectly dry: increase the dosage by turning the dial to a higher setting (5-6). Plastic dishes have more difficulty drying and a higher rinse aid setting will not improve the situation.
Detergents with rinse aid incorporated may be effective only with longer programs. In the case of shorter programs, detergent residue may be a problem (if necessary, use powder detergent). Detergents with rinse aid incorporated tend to form excess suds.
Adding detergent - Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations |
Daily use |
|
|
|
|
Open the cover A (press the dedicated button).
3
Insert detergent: Tablet / powder / liquid into the big chamber. Please look for the recommendation of the detergent manufacturer on the packaging of the detergent product.
Only fill the detergent dispenser prior to starting a wash program.
Use only one tablet per one cycle, only placed in detergent dispenser.
All types of tablets can be used, but for 2 in 1 type adding of salt is mandatory.
Some types of tablets may not dissolve completely during the short cycles (Rapid, Fragile, Handwash); placing the tablet on the tub bottom can help dissolving and washing.
Shut the cover
by pressing dedicated ribs.
GB -3-