Whirlpool ADG 987/2 WH, ADG 987/2 NB, ADG 987/2 IX PROGRAM CHART
.
Quick reference guide
PROGRAMME
SELECTION
BUTTON
(See programme
chart below)
START BUTTON
The indicator lights up during operation, flashes when a fault occurs, and goes off
at the end of the programme.
START BUTTON RESET FUNCTION:
Press this button for at least 2 seconds; the selected programme and options will
be cancelled. Main failure displays (repeated flashing of the START indicator lamp)
can be cancelled by RESETTING. Detailed instructions are given in chapter
“What to do if...”.
START
MULTI
ZONE
option
POWER
CLEAN
option
DELAY
option
(see at right for options description)
ON/OFF
BUTTON
BEFORE USING THE APPLIANCE FOR THE
FIRST TIME CAREFULLY READ THIS QUICK
REFERENCE GUIDE AND THE INSTALLATION
INSTRUCTIONS! THE GUARANTEE IS NOT
APPLICABLE IF FAULTS ARE CAUSED BY
INCORRECT USE OF THE APPLIANCE.
Options and display description
SALT INDICATOR
When lit, the salt reservoir
needs to be refilled.
FAULT INDICATION AND WASH TIME DISPLAY
In normal operation it indicates the remaining time
(h:mm), whereas with “Delayed start” selected it
indicates the time remaining until programme start (hh).
If “F..” appears on the display, see chapter “What to do
if...”.
Chart
Table of programmes
Detergent
X 7-17 0.99-1.75 65-220
X 10.0 0.85 100
X*10.0 0.65 30
X 13.0 1.50 115
X 13.0 1.20 290
50°C
Available
options
Delay
Multizone
Power Clean
Delay
Multizone
Delay
Multizone
Delay
Multizone
Delay
Multizone
Power Clean
Delay
Multizone
Power Clean
Delay
Multizone
Loading instructions Litres kWh
Normally or heavily soiled
crockery, including pots and pans.
Thanks to steam action, soaking or
hand pre-treatment is no longer
needed. In addition hygiene is
ensured due to the high
temperature steam.
Crockery to be washed later. — 4.0 0.03 14
Light soiling, for example glasses
and cups.
Lightly soiled crockery, with no
dried-on food.
not recommended.
Normally soiled crockery. X 11.0 1.05 165
Normally or heavily soiled crockery,
with additional antibacterial wash.
Programme interruption (e.g. due
to door opening) can compromise
elimination of germs.
Normally soiled crockery, gentle and
quiet thanks to the lower spray
pressure (39 dbA).
* Use of tablets
P
1
2
3
4
5
6
7
1) Programme data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional options) and may vary
depending on conditions. Differences of up to 20 minutes are possible with sensor programmes as a result of the appliance’s automatic calibration system
2) Reference programme for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the
EN/Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.
3)The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.
Programmes
Aqua Steam 40-70°C
Pre-Wash cold
Glasses 40°C
Quickwash 40°C
2)
Bio
Antibacterial
Overnight 55°C
3)
Consumption
Minutes
1)
RINSE AID INDICATOR
When lit, the rinse aid dispenser
needs to be refilled.
DELAYED START
BUTTON
Press the button
(repeatedly) to delay the
start of the programme.
Adjustable from 1 to 24
hours. With each press of
the button, the delayed
start indicator increases by
one hour and after 24
restarts from 00. Then
press the START button.
The dishwasher will start
after the set time.
HALF LOAD/
MULTIZONE
Allows you to choose the
washing zones. Press this
button to select the wash
zones:
both racks
only upper rack
only lower rack
5019 396 01733ADG 987
POWER CLEAN
Thanks to the additional
power jets this option
provides a more intensive
and powerful wash in the
lower rack, in the specific
area.This option is
recommended for washing
pots and casseroles
. Press this button
page 4)
to activate Power Clean
(the indicator lights up).
(see
GB
-1-
How to set detergent type: powder/gel/tablet (if option is available)
First time use
In order to always ensure the best cleaning
results, you NEED to set:
DETERGENT type and WATER HARDNESS.
1- salt reservoir
2- rinse aid dispenser
3- detergent dispenser
4- racks system
5,6,7,8- available functions on the panel
9- filters
10- spray arms
1.
Select 3rd programme
(see Table of programmes
- page 1)
2.
Press START button
for 7 seconds
3a.
Check your
detergent type...
Detergent
types
Powder or gel
(factory setting)
Tablet 2 in 1
Tablet 3 in 1
Tablet All in 1
3b.
...and set it on your dishwasher
using the START button
(as per table below)
Dishwasher models
model without
display
3h 6h 9h
model with display
For models without “detergent type” option, the salt and rinse aid indicators will be lit when tablets are used.
How to set water hardness
Switch on the appliance
- Select the 2nd programme “P2” - consult the table in the Programme Chart.
*
before the first wash
only
water hardness has been changed
1.
Ask your water supply
company what the
hardness
is...
French
degrees °fH
0 - 9 Soft 1 1x go to step 2 go to step 3
10 - 18 Medium 2 2x
19 - 27 Average 3 3x
28 - 37 Medium-hard 4 4x
38 - 50 Hard 5 5x
51 - 63 Very hard 6 6x
64 - 107 Extremely hard 7 7x
water
Water
hardness
or if the
2.
...enter this value on your dishwasher
Dishwasher with
display: insert value
in the display
- Press the START button for at least 5 seconds until the START indicator lamp flashes.
- The water hardness setting is shown on the display (if present) or the START button flashes.
- With each successive touch of the START button the setting increases and when it reaches 7 it returns to 1 again.
- The appliance must be switched off to memorise the new setting.
Suggestions for detergent use
Dishwasher without
display: count START
button led flashes
Gel or Powder
(rinse aid and salt)
go to step 1
if extra salt is needed go
to step 1 and then 3
4.
Remember to use salt and rinse
aid when needed (as indicated
below)
no symbol add salt add rinse aid
add salt
salt
Tablets
rinse aid
rinse aid
Water hardness level is factory set for
medium hard water (a number “4” is
shown on the display or the START
indicator lamp flashes 4 times).
go to step 3
Even if you use tablets which include salt,
you must still add salt since such
detergents are not effective enough at
softening hard water.
5.
Switch off and switch on
again to save setting
GB
-2-
1
Filling the salt reservoir -
Dissolve limescale (not necessary if water hardness level is set to “soft”!)
Daily check
The salt level indicator lamp may remain lit for the duration of several wash cycles. If the
water hardness level falls within category (soft), no salt is required.
Adding rinse aid
(not necessary when you use tablets). How to adjust the rinse aid dosage regulator
2
Rinse aid
indicator (depending on model)
Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away any rinse aid spilt accidentally. This p revents the formation of excess suds which can cause a fault function of the appliance.
If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is not perfectly d ry : incr e a s e the dosage by turning the dial to a higher setting (5-6). Plastic dishes have more difficulty drying and a higher rinse aid
setting will not improve the situation.
Detergents with rinse aid incorporated may be effective only with longer programmes. In the case of shorter programmes, detergent residue may be a problem (if necessary, use powder detergent). Detergents with rinse aid incorporated tend
to form excess suds.
Adding detergent -
Visual indicator
(depending
on model).
Unscrew cap.
Visual
indicator B
If required, open
the cover (press
lever).
The indicator lamp on the control panel lights up when RINSE AID NEEDS TO BE
ADDED.
Fill the salt
reservoir with
water before the
first wash only.
Salt indicator
(depending on
the model)
Add rinse aid
to max.
line ~100 ml
The indicator lamp on the control panel
lights up when SALT NEEDS TO BE
ADDED.
Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations.
Tablet / gel / powder
Add salt
(never add
detergent!).
min. 1.5 kg
max. 2 kg
orange: OK. clear: NEEDS TO BE ADDED
The rinse aid dosage can be adjusted to the
detergent used. The lower the setting, the less
rinse aid is dispensed (factory setting: position 4).
Press the lever to open the cover. Using a coin or
similar object, turn the arrow to the desired
setting. After adjusting the rinse aid setting, shut
the cover again.
dark: OK. clear: NEEDS TO BE ADDED
Visual indicator (depending
on model). Screw on the cap.
Salt residues around cap
need to be removed.
Daily use
3
Open the cover A
(press lever).
Only fill the
detergent dispenser
prior to starting a
wash programme.
Use only one tablet per cycle,
placed in the detergent
dispenser.
GB
-3-
Loading...