Whirlpool ADG7554WHM Service Manual
SERVICE
Model 6ADG 7554 WHM
Version 8542 554 53710 Page
Whirlpool Europe
Customer Services
6ADG 7554 WHM
Service Manual
Dishwasher
integratable
6ADG 7554 WHM
Technical data 2 - 3
Spare part list 4 - 5
Exploded view 6 - 7
Circuit diagram 8
Program diagram 9
Text/Legend 10 - 16
Family MID 5
This documentation is only intended for qualified technicians who are aware of the respective safety regulations.
Date: 08.08.2002 Subject to modification
Document-No.: 4812 718 18228
08.08.2002 / Page 2 6ADG 7554 WHM Whirlpool Europe
Doc. No: 4812 718 18228 8542 554 53710 Customer Service
Technical data
SERVICE
Dimension
Height 82.0 - 87.0cm
Width 59.7 cm
Depth 55.5 cm
Weight 52 kg
Wooden door for Full Door appliances
Thickness min. 16 mm
Thickness max. 20 mm
Width min. 592 mm
Width max. 595 mm
Height min. 620 mm
Height max. 718 mm
Weight min. 2.5 kg
Weight max. 6.5 kg
Max. stick out over lower
edge of appliance door 92 mm
Height of plinth min. 93 mm
Electronic boards
Service boards see spare part list
Serial boards see on the boards itself
DUB 4619 720 80502
Programing of version and programmed control
board, see „Service“ and „Data set“ on rating
plate of inner door:
CB programmed 464711
Data set 464701
Basic control board, not programmed see on the
board itself 4619 724 17441
Program information
End - Acoustic signal
All programs will be locked after start. Changing
the program or finishing the program will be
possible only after pressing the start button for
longer then 1.5 sec. (Break by customer)
A switching off the appliance or unplug the
appliance for a while, this will frozen the program
step and later on, the program continuos on the
same position.
Exception: Switching off the appliance or unplug
the appliance during the drying phase, this will lead
directly to the end of the program.
Water Volume at alternating spray system
Volume at alternating spray system (same level
when selected zone washing as in the normal
programs)
Water Volume Level
Regeneration 0.3 l 15 mm
Back rinse 3x 1.0 l 60 mm
Prewash 3.9 l 120 mm
Main wash 3.2 l 118 mm
Intermediate rinse 1 3.2 l 118 mm
Intermediate rinse 2 3.2 l 118 mm
Clear rinse 3.2 l 118 mm
Safety/ overflow 8.5 l 141 mm
Succession of programs
Programs see program diagram
Succession A1a - A3a - A5b - A6a - A7a
Alarms
Refill rinse aid
Options
Zone washing
Measuring the level
Remove the coarse sieve, put in a measuring
meter into the sump, measure the hight of the
water level.
Detergent max.
Pre-wash 10 cm
Main-wash 40 cm
Rinse aid 135 cm
6 Dosage steps 1 - 6 ml
Water pressure
Inlet pressure 0.3 - 10 bar
Spray pump pressure 0.3 bar
Rotations
Spray pump motor 2800 RPM
Drain pump motor 3000 RPM
Spray arm lower 30 - 40 RPM
Spray arm upper 30 - 40 RPM
3
3
3
SERVICE
Technical data
Whirlpool Europe 6ADG 7554 WHM 08.08.2002 / Page 3
Customer Service 8542 554 53710 Doc. No: 4812 718 18228
Spray arms, turning rhythm at alternating spray
system
Turning starts every time with the upper spray arm
Pre wash Lower arm ~3min, Upper arm ~1min
Main wash Lower arm ~3min, Upper arm ~5min
Intermediate rinse
Lower arm ~2min, Upper arm ~2min
Final rinse Lower arm ~2min, Upper arm ~2min
Service Test program
Lower arm ~30sec, Upper arm ~30sec
Remark: When switching of the main switch or
interrupt the mains during the Test Program runs,
then the alternating of the spray arms change in
the test program to the rhythm of main wash 5/3
min.
Important: To leaf the Test program is possible by
made a break by customer (pushing the start
button for 1.5 sec.)
After finishing the test program (End LED shines
and/or Start LED goes of) must the appliance be
switched off.
If this will not be done, then the next normal wash
will be made with the frequency of the Service
Test Program ~30/30sec.
Resistance 146 Ω
Flow rates/ Inlet volume
Flow meter (at 0.3 bar
= quantity 1.1 l/min) 208 lmp/l
Spray pump 45 - 65 l/min
Drain pump 16 l/min
Pump height max. 1.1 m
Inlet valve 4 l/min
Spray arm lower ~ 33 l/min
Sprayarm upper ~ 27 l/min
Shower top ~ 8 l/min
Electrical base data
Voltage 240 V
Frequency 50 Hz
Total power 2.4 kW
Fuse 10 A
Motor
Spray pump motor alternating spray system
Voltage 220/ 240 V
Power consumption 125 W
HI 79 Ω
HA 60 Ω
Capacitor 4 µ F
Drain pump motor
Voltage 220/ 240 V
Power consumption 30 W
08.08.2002 / Page 4 6ADG 7554 WHM Whirlpool Europe
Doc. No: 4812 718 18228 8542 554 53710 Customer Service
Heating (1 Element system)
Voltage 240 V
Power consumption 2.22 kW
Resistance 24.5 Ω
Heating speed ~ 2.0 ˚C/min
Temperature on surface ~ 115 ˚C
Safety thermostat
self reset
(Temperature of water) ~ 85 ˚C
Fuse 206 ˚C
Single electric inlet valve
Voltage 220/ 240 V
Frequency 50/ 60 Hz
Resistance 3.76 kΩ
Valve for zone washing
Voltage 220 - 240 V
Frequency 50/ 60 Hz
Resistance 4 kΩ
SERVICE
Coil of dispenser
Voltage 220/ 240 V
Frequency 50/ 60 Hz
Resistance 1.3 kΩ
Reed contacts
flow meter
rinse aid control
NTC
20 ˚C 58.1 kΩ
25 ˚C 47.1 kΩ
30 ˚C 38.2 kΩ
40 ˚C 25.4 kΩ
50 ˚C 17.2 kΩ
60 ˚C 11.8 kΩ
70 ˚C 8.3 kΩ
80 ˚C 6 kΩ
85 ˚C 4 kΩ
Accesory
If you need spare parts apart from the spare
part list have a look in the
Service Bulletin 4812 718 40084.
08.08.2002 / Page 4 6ADG7554WHM Whirlpool Europe
Doc. No: 4812 718 18228 8542 554 53710 Customer Service
Spare part list
Model 6ADG 7554 WHM
Service No. 854255453710
Version 854255453710
SERVICE
Pos. No. 12NC Code Description
003 0 4812 440 19594 Traverse
004 0 4812 440 18952 Drip tray assy
004 1 4812 401 18402 Holder
011 0 4812 505 18369 Foot long
022 0 4812 440 19398 Side panel left
022 1 4812 440 19397 Side panel right
024 0 4812 440 10417 Panel, rear
040 1 4812 417 18774 Hinge left
040 2 4812 417 18773 Hinge right
044 0 4812 492 38362 Spring f.door
047 0 4812 404 48746 Brake f.door
047 1 4812 401 18397 Band,brake
047 2 4812 404 68023 Hook
053 0 4812 440 88884 Plinth
103 0 4812 440 19478 Door outer
105 0 4812 404 48611 Fastener door
105 2 4812 505 68004 Clip
105 3 4812 404 48633 Fastener
120 0 4812 440 19456 Door,inner
120 1 4812 440 18969 Batten
130 0 4812 417 58361 Tilt lock cpl. wh
131 0 4812 401 18416 Hook lock
175 3 4812 466 68572 Batten
191 0 4812 466 68564 Gasket door
192 0 4812 466 68467 Gasket, door lower
Pos. No. 12NC Code Description
421 0 4812 121 18158 Interf.filter
430 0 4812 360 18508 Pump,draining cpl.
430 1 4812 466 68689 Gasket
450 0 4812 259 28684 Heating element
480 0 4812 321 28407 Cable harness set
480 1 4812 321 28371 Cable
480 3 4812 401 18418 Protector f.wiring
490 0 4812 321 18051 Cable,mains
490 1 4812 321 28367 Strain relief
521 0 4812 214 78859 Control board (CB)
583 0 4812 271 28407 Switch diaphragm
616 1 4812 271 58161 Contact,reed rinsing agent
620 0 4812 218 38068 User board (UB)
623 0 4812 271 38356 Microswitch
633 0 4812 271 38355 Microswitch door
680 0 4812 418 68155 Combidosage
680 1 4812 466 68495 Gasket
681 1 4812 466 68497 Gasket
681 2 4812 440 18975 Flap
682 0 4812 466 68496 Gasket
691 0 4812 282 68012 Feeler NTC
700 0 4812 530 28804 Hose, inlet aqua stop 4,2m
700 0 4812 530 28848 Hose, inlet aqua stop 2m
700 1 4812 480 48095 Sieve
700 2 4812 466 68628 Gasket
241 0 4812 458 19027 Basket upper straight
241 1 4812 458 18324 Holder cups right wh
241 3 4812 528 88068 Wheel,basket upper (set)
241 4 4812 458 18984 Holder dishes wh
241 5 4812 535 78043 Bearing
241 6 4812 458 18979 Holder glasses wh
241 7 4812 404 48683 Hoop
241 8 4812 466 68553 Spacer cap set
242 0 4812 310 28136 Basket lower KIT
242 1 4812 528 88069 Wheel,basket lower wh
242 4 4812 466 48059 Fixation wh
242 6 4812 458 18977 Support plate left
242 7 4812 458 18978 Support plate right
243 0 4812 458 18272 Basket cutlery
243 5 4819 310 39859 Cutlery basket KIT
243 6 4812 458 18996 Grille wh
261 0 4819 462 38271 Rail telescope, inner
261 1 4812 462 79768 Cap rail
261 2 4812 462 78995 Cap rail ahead
263 0 4819 520 18013 Ball cage cpl.
263 1 4812 520 48001 Ball Niro 8 D
265 0 4812 404 48637 Basket adjustm. cpl.
265 2 4812 404 48638 Grip basket adjustment
301 0 4812 453 79762 Control panel WH
322 0 4812 453 71655 Insert panel cpl.
701 1 4812 310 18153 Yoke clamp set
710 2 4819 310 38536 Threaded ring
710 3 4819 466 69562 Gasket set
714 0 4812 462 78012 Threaded cap
716 0 4812 418 68142 Reg.dosage
716 1 4812 466 68475 Gasket
716 2 4812 462 78994 Cover
717 0 4812 281 28418 Valve motordiverter
717 2 4812 528 98011 Valve disk diverter
717 3 4812 530 29121 Gasket diverter valve
721 1 4812 360 68347 Spray arm lower. cpl.
722 0 4812 360 68348 Spray arm upper wh
722 2 4812 360 68349 Spray arm 2nd level cpl. wh
723 0 4812 360 68351 Douche ceiling
726 1 4812 530 29118 Tube assembly cpl.
726 2 4812 505 18208 Nut
743 0 4812 511 48171 Capacitor
743 1 4812 530 28102 Hose, inlet
743 3 4812 505 18364 Nut
743 4 4812 530 28807 Hose 9x1,5x270+10
743 7 4812 466 68514 Gasket
751 0 4812 418 18338 Water collector
755 0 4812 530 29119 Bend
755 2 4812 530 48148 Tray,leak
756 0 4812 360 58099 Floater
332 5 4812 410 28556 Cap f.beater
400 0 4812 361 58336 Motor +SP,50Hz,alt.LP-PNT1
405 0 4812 360 18509 Spray pump wo.Mot.alt.LP-50Hz
405 1 4819 515 28158 Gasket
420 0 4812 121 18132 Capacitor
761 0 4812 480 58122 Sieve fine
761 2 4812 418 18337 Cover sieve
761 3 4812 418 18341 Cover
761 4 4812 530 58141 O-Ring
763 0 4812 480 58123 Sieve coarse
Whirlpool Europe 6ADG7554WHM 08.08.2002 / Page 5
SERVICE
Customer Service 8542 554 53710 Doc. No: 4812 718 18228
Spare part list
Model 6ADG 7554 WHM
Service No. 854255453710
Version 854255453710
Pos. No. 12NC Code Description
781 0 4812 530 29113 Hose,draining
781 3 4812 281 28417 Flap non-return
783 6 4812 530 28824 Hose 10,3X3X245
791 0 4812 532 68099 Gasket
791 4 4812 466 68503 Gasket
791 5 4812 466 68504 Gasket
901 0 4822 401 10258 Clamp,hose 10-18 mm
901 1 4812 401 18424 Strap 050,0
901 2 4812 401 18157 Strap 32-50/9 C61
901 5 4812 401 48573 Strap 028,6
901 8 4812 401 18075 Strap 20-32/9 mm
902 1 4812 466 78015 Fastener f.buildt-in models
902 2 4812 404 78241 Holder
904 2 4812 462 79657 Cover BK 3,5x5
904 4 4812 462 79659 Threaded cap
910 1 4812 502 38152 Screw 4,8x19
910 2 4812 502 18363 Screw 4,0x12-H
910 3 4812 502 18389 Screw 5x20 T20
910 4 4812 502 18385 Screw M3,5x8-T15M
910 5 4812 502 18393 Screw 3,5x9-1 Tx15
910 7 4812 502 18397 Screw INOX A2 M 5X12
910 8 4812 502 18527 Screw 4x15 T20
964 1 4812 466 68573 Gasket housing upper
993 1 4812 466 78388 Foil protection
993 2 4812 404 48753 Key foot
993 6 4812 466 78386 Foil protection add.
994 1 4812 310 28022 Fastener set n.sh.
Loading...