Whirlpool 8TWTW6000JW, 8TWTW4955JW, 8TMVWC585JW Installation Instructions

WASHER INSTALLATION INSTRUCTIONS

洗衣機安裝說明

Table of Contents

WASHER SAFETY ..............................................................1

INSTALLATION REQUIREMENTS .....................................2

TOOLS AND PARTS .............................................................. 2

LOCATION REQUIREMENTS ............................................... 2

DRAIN SYSTEM .................................................................... 3

ELECTRICAL REQUIREMENTS ........................................... 4

INSTALLATION INSTRUCTIONS .......................................4

CONNECT DRAIN HOSE ...................................................... 5

CONNECT INLET HOSES..................................................... 6

LEVEL WASHER ................................................................... 7

COMPLETE INSTALLATION CHECKLIST ........................... 8

INSTALLATION NOTES / 安裝備註

Date of purchase / 購買日期： _______________________ Date of installation / 安裝日期： ______________________ Installer / 安裝人員： _______________________________ Model number / 型號： _____________________________ Serial number / 序號： _____________________________

洗衣機安全 ...........................................................................9

安裝要求 ............................................................................10

工具和零件 ........................................................................... 10

場地需求 ............................................................................... 10

排水系統 ............................................................................... 11

電源需求 ............................................................................... 12

安裝說明 ............................................................................12

連接排水管 ........................................................................... 13

連接進水管 ........................................................................... 14

調整水平 ............................................................................... 15

完成安裝檢查清單 ................................................................. 16

WASHER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

You can be killed or seriously injured if you don't immediately

DANGER

WARNING

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

follow instructions.

You

can be killed or seriously injured if you don't

instructions.

W11317128B

271/2"

INSTALLATION REQUIREMENTS TOOLS AND PARTS

Gather required tools and parts before starting installation.

Tools needed:

Adjustable or open end wrench 9/16"

4" min

(102 mm)

Level

Alternate parts: (Not supplied with washer)

Your installation may require additional parts. To order, please refer to toll-free numbers on back page of your Use and Care Guide.

If you have: You will need:

Overhead sewer Standard 20 gal. (76 L) 39" (990 mm) tall drain tub or utility sink, sump pump and connectors (available from local plumbing suppliers)

1" (25 mm) standpipe 2" (51 mm) diameter to 1" (25 mm) diameter Standpipe Adapter Part Number 3363920 Connector Kit Part Number 285835

Drain hose too short Extension Drain Hose Part Number 285863 Connector Kit Part Number 285835

Lint clogged drain Drain Protector Part Number 367031 Connector Kit Part Number 285835

Wood block

Pliers that open to 13⁄4"

Ruler or measuring tape

Optional tools:

Flashlight Bucket

Parts supplied:

NOTE: All parts supplied for installation are in cardboard

insert in the top of the washer.

LOCATION REQUIREMENTS

Select proper location for your washer to improve performance and minimize noise and possible “washer walk”. Install your washer in a basement, laundry room, closet, or recessed area.

(699 mm)

42"

(1067 mm)

You will need:

■

A water heater set to 120°F (49°C).

■

A grounded electrical outlet located within 4 ft (1.2 m) of

power cord on back of washer.

■

Hot and cold water faucets located within 3 ft (0.9 m) of hot

and cold water ll valves on washer, and water pressure of 20-100 psi (138-690 kPa).

■

A level oor with maximum slope of 1" (25 mm) under entire

washer. Installing on carpet is not recommended.

■

Floor must support washer’s total weight (with water and load)

of 315 lbs (143 kgs).

27"

(686 mm)

Drain hose with clamp, U-form, and cable tie

Inlet hoses with flat washers

IMPORTANT: Do not install, store, or operate washer where it will be exposed to weather or in temperatures below 32°F (0°C). Water remaining in washer after use may cause damage in low temperatures. See “Washer Care” in your Use and Care Guide for winterizing information.

Proper installation is your responsibility.

Recessed area or closet installation

4.5"

(114 mm)

Floor drain system

(76 mm)

14" max.

(356 mm)

(101 mm)

(25 mm)

19"

(482 mm)

(25 mm)

(76 mm)

48 in.

(310 cm2)

24 in.

(155 cm2)

Dimensions show recommended spacing allowed, except for closet door ventilation openings which are minimum required. This washer has been tested for installation with spacing of 0" (0 mm) clearance on the sides. Consider allowing more space for ease of installation and servicing, and spacing for companion appliances and clearances for walls, doors, and oor moldings. Add spacing of 1" (25 mm) on all sides of washer to reduce noise transfer. If a closet door or louvered door is installed, top and bottom air openings in door are required.

DRAIN SYSTEM

Floor drain system requires a Siphon Break Kit (Part Number

285834), 2 Connector Kits (Part Number 285835), and an Extension Drain Hose (Part Number 285863) that may be purchased separately. To order, please see toll-free phone numbers in your Use and Care Guide. Minimum siphon break: 28" (710 mm) from bottom of washer. (Additional hoses may be needed.)

Laundry tub drain system

39"

(990 mm)

Minimum capacity: 20 gal. (76 L). Top of laundry tub must be at least 39" (990 mm) above oor; install no higher than 96" (2.44 m) from bottom of washer.

IMPORTANT: To avoid siphoning, no more than 4.5" (114 mm) of drain hose should be inside standpipe or below the top of wash tub. Secure drain hose with cable tie.

Drain system can be installed using a oor drain, wall standpipe, oor standpipe, or laundry tub. Select method you need.

Floor standpipe drain system

39"

4.5"

(114 mm)

(990 mm)

Minimum diameter for a standpipe drain: 2" (51 mm). Minimum carry-away capacity: 17 gal. (64 L) per minute. Top of standpipe must be at least 39" (990 mm) high; install no higher than 96" (2.44 m) from bottom of washer. If you must install higher than 96" (2.44 m), you will need a sump pump system.

Wall standpipe drain system

4.5"

(114 mm)

See requirements for oor standpipe drain system.

ELECTRICAL REQUIREMENTS

INSTALLATION INSTRUCTIONS

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

■

A 120 V, 60 Hz, AC only, 15 or 20 A, fused electrical supply is

required. A time-delay fuse or circuit breaker is recommended. It is recommended that a separate circuit breaker serving only this appliance be provided.

■

This washer is equipped with a power supply cord having

a 3 prong grounding plug.

■

To minimize possible shock hazard, the cord must be plugged

into a mating, 3 prong, grounding-type outlet, grounded in accordance with local codes and ordinances. If a mating outlet is not available, it is the personal responsibility and obligation of the customer to have the properly grounded outlet installed by a qualied electrician.

■

If codes permit and a separate ground wire is used, it is

recommended that a qualied electrician determine that the ground path is adequate.

■

Do not ground to a gas pipe.

■

Check with a qualied electrician if you are not sure the

washer is properly grounded.

■

Do not have a fuse in the neutral or ground circuit.

WARNING

Excessive Weight Hazard

Use two or more people to move and install washer.

Failure to do so can result in back or other injury.

Before you start: remove shipping materials.

It is necessary to remove all shipping materials for proper operation and to avoid excessive noise from washer.

1. Move washer

48"

(1.2 m)

Move washer to within 4 ft (1.2 m) of its nal location; it must be in a fully upright position.

NOTE: To avoid oor damage, set washer onto cardboard before moving it and make sure lid is taped shut.

2. Remove shipping base

To avoid damaging oor, place cardboard supports from shipping carton on oor behind washer. Tip washer back and place on cardboard supports. Remove shipping base by rotating base 90° to the right. Set washer upright.

IMPORTANT: Removing shipping base is necessary for proper operation. If your washer includes a sound shield, please refer to the instructions included with the sound shield to install it at this time.

3. Remove packing tray from tub

Remove tape from washer lid, open lid and remove cardboard packing tray from tub. Be sure to remove all parts from tray.

NOTE: Keep tray in case you need to move washer later.

4. Free power cord

CONNECT DRAIN HOSE

5. Attach drain hose to drain port

If clamp is not already in place on elbow end of drain hose, slide it over end as shown. Squeeze clamp with pliers and slide black elbow end of drain hose onto black drain port and secure with clamp.

For a laundry tub or standpipe drain, go to step 6.

For a oor drain, remove the preinstalled drain hose form as shown in Step 7. You may need additional parts with separate directions. See “Tools and Parts”.

Firmly grasp power cord plug and pull to free from rear panel. Gently place power cord over console to allow free access to back of washer.

6. Place drain hose in standpipe

Drain hose form

4.5"

(114 mm)

Place hose into standpipe (shown in picture) or over side of laundry tub.

IMPORTANT: 4.5" (114 mm) of drain hose should be inside standpipe; do not force excess hose into standpipe or lay on bottom of laundry tub. Drain hose form must be used.

+ 11 hidden pages