Whirlpool WTW5015LW, WTW5010LW, WTW5057LW, 7MWTW5017MW, 7MWTW5057MW Dimension Guide
WTW5015LW, WTW5010LW
WTW5057LW, 7MWTW5017MW
7MWTW5057MW
Dimension Guide
Whirlpool® Top Load Washer
W11428629A
DETAILED PLANNING DIMENSIONS
WARNING: To reduce the risk of re, electric shock, or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS and
INSTALLATION INSTRUCTIONS, located in your appliance's Owner's Manual, before installing and operating this appliance.
Electrical Requirements
WTW5015LW - 4.5 cu ft DOE (US), 5.2 cu ft IEC (CAN)
WTW5010LW - 4.6 cu ft DOE (US), 5.3 cu ft IEC (CAN)
WTW5057LW - 4.7 cu ft / 4.8 cu ft DOE (US), 5.4 cu ft / 5.5 cu ft IEC (CAN)
7MWTW5017MW - 4.5 cu ft DOE (US), 5.2 cu ft IEC (CAN)
7MWTW5057MW - 4.7 cu ft DOE (US), 5.4 cu ft IEC (CAN)
Minimum Circuit Amperage Rating 15 A
Operating Voltage 120 V AC only
Operating Frequency 60 Hz
D
A
C
B
Product Dimensions
WTW5015LW, WTW5010LW, WTW5057LW, 7MWTW5017MW, 7MWTW5057MW
in (minimum) mm (minimum) in (maximum) mm (maximum)
A Height (with feet) 411∕
2
1048 421∕
B Width 27¾ 683 - C Top of Lid Height (with feet) 381∕
2
962 382∕
D Depth 27 692 - -
4
3
1074
982
2
DETAILED PLANNING DIMENSIONS
G
I
J
F
E
H
K
WTW5015LW, WTW5010LW, WTW5057LW, 7MWTW5017MW, 7MWTW5057MW
in (minimum) mm (minimum) in (maximum) mm (maximum)
E Height with Lid Open 553/
F Height of Lid 187∕
G Width of Lid 231∕
H Water Inlet Valves Height 377∕
I Water Inlet Valves from Side 41∕
J Power Cord from Side 21∕
K Power Cord Height 373∕
Power Cord Length 62 1530 - L Drain Hose Outlet Height 71∕
M Drain Hose Outlet from Side 45∕
Drain Hose Length 41 1040 - -
Diameter of Drain Hose 1 25 - -
Product Dimensions
4
8
4
8
2
2
8
4
16
1415 563∕
449 - 593 - 962 391∕
116 - -
63 - -
950 371∕
170 73∕
107 - -
L
M
8
2
2
4
1432
1003
953
197
3
DETAILED PLANNING DIMENSIONS
Recessed area or closet installation
14"
(356 mm)
maximum
5"
(126 mm)
3"
(76 mm)
3"
(76 mm)
2
48 in
(310 cm2)
2
24 in
(155 cm2)
1"
1"
(25 mm)
(25 mm)
3"
(76 mm)
Dimensions show recommended spacing allowed, except for closet door ventilation openings which are minimum required.
This washer has been tested for installation with spacing of 0" (0 mm) clearance on the sides. Consider allowing more space for ease
of installation and servicing, and spacing for companion appliances and clearances for walls, doors, and oor moldings. Add spacing
of 1" (25 mm) on all sides of washer to reduce noise transfer. If a closet door or louvered door is installed, top and bottom air openings
in door are required.
Loading...