Whirlpool 6AWTW5550XW0 Parts Diagram
220–240V 50 Hz WASHER INSTALLATION INSTRUCTIONS
Table of Contents
WASHER SAFETY ..............................................................2
WASHER DISPOSAL ..........................................................2
INSTALLATION REQUIREMENTS .....................................3
Tools and Parts ..................................................................... 3
Location Requirements ....................................................... 3
Drain System ........................................................................ 4
Electrical Requirements ...................................................... 5
INSTALLATION INSTRUCTIONS .......................................5
Before you start: remove shipping materials ....................5
Connect Drain Hose ............................................................. 6
Connect Inlet Hoses ............................................................. 7
Level Washer ........................................................................8
Complete Installation Checklist .......................................... 9
INSTALLATION NOTES
Date of purchase: _________________________________________
Date of installation: _______________________________________
Installer: _________________________________________________
Model number: ___________________________________________
Serial number: ____________________________________________
W10045638A
Models
6AWTW5700X
6AWTW5550X
WASHER SAFETY
WASHER DISPOSAL
2
699 mm
INSTALLATION REQUIREMENTS
Tools and Parts
Gather required tools and parts before starting installation.
Tools needed:
Adjustable or open-end
wrench 14 mm (9/16")
102 mm
min
(4")
Wood block
Pliers that open to 39.5 mm (19⁄16")
Optional tools:
Level
Ruler or measuring tape
Your installation may require additional parts. For information on
ordering, contact your dealer.
n
8212656RP 3.0 m (10 ft.) Inlet hose, Black EPDM (2 pack)
n
8212641RP 1.5 m (5 ft.) Inlet hose, Black EPDM (2 pack)
n
8212646RP 1.2 m (4 ft.) Inlet hose, Black EPDM (2 pack)
n
8212545RP 1.5 m (5 ft.) Inlet hose, Red and Blue EPDM
(2 pack)
n
8212487RP 1.5 m (5 ft.) Nylon braided inlet hose (2 pack)
n
8212638RP 1.8 m (6 ft.) Nylon braided inlet hose, space
saving 90° elbow, hypro-blue steel couplings
(2 pack)
n
8212637RP 1.8 m (6 ft.) Inlet hose, Black EPDM, space
saving 90° elbow, hypro-blue steel couplings
(2 pack)
Alternate parts: (Not supplied with washer)
Your installation may require additional parts. For information on
ordering, contact your dealer.
If you have: You will need:
Overhead sewer Standard 76 L (20 gal.) 990 mm (39")
tall drain tub or utility sink, sump
pump, and connectors (available
from local plumbing suppliers)
25 mm (1") standpipe 51 mm (2") diameter to 25 mm (1")
diameter Standpipe Adapter
Part Number 3363920
Connector Kit Part Number 285835
Drain hose too short Extension Drain Hose Part
Number 285863
Connector Kit Part Number 285835
Lint clogged drain Drain Protector Part Number 367031
Connector Kit Part Number 285835
Flashlight Bucket
Parts supplied:
NOTE: All parts supplied for installation are in
cardboard insert in the top of the washer.
Beaded tie strap Drain hose with clamp
Water inlet hose (2)
A
A Large flat washer (4)
B Inlet hose adapter (2)
C Small flat washer (2)
B
C
Technical Specications
220–240 V
~50 Hz. AC
IP24
Clothes Capacity
6AWTW5550: 8.0 Kg Max.
6AWTW5700: 8.0 Kg Max.
LOCATION REQUIREMENTS
Select proper location for your washer to improve performance
and minimize noise and possible “washer walk.” Install your
washer in a basement, laundry room, closet, or recessed area.
(271/2")
1067 mm
(42")
686 mm
(27")
3
You will need:
76 mm
n
A water heater set to 60° C (140° F).
n
An earthed electrical outlet located within 1.2 m (4 ft) of power
cord on back of washer.
n
Hot and cold water faucets located within 0.9 m (3 ft) of
hot and cold water ll valves on washer, and water pressure
of 138–690 kPa (20–100 psi).
n
A level oor with maximum slope of 25 mm (1") under entire
washer. Installing on carpet is not recommended.
n
Floor must support washer’s total weight (with water and load)
of 143 kgs (315 lbs).
IMPORTANT: Do not install, store, or operate washer where it will
be exposed to weather or in temperatures below 0° C (32° F).
Water remaining in washer after use may cause damage in low
temperatures. See “Washer Care” in your “Use and Care Guide”
for winterizing information.
Proper installation is your responsibility.
Recessed area or closet installation
(3")
DRAIN SYSTEM
Drain system can be installed using a oor drain, wall standpipe,
oor standpipe, or laundry tub. Select method you need.
Floor standpipe drain system
Minimum diameter for a standpipe drain: 51 mm (2"). Minimum
carry-away capacity: 64 L (17 gal.) per minute. Top of standpipe
must be at least 990 mm (39") high; install no higher than 2.44 m
(96") from bottom of washer. If you must install higher than
2.44 m (96"), you will need a sump pump system.
Wall standpipe drain system
356 mm
max.
(14")
126 mm
(5")
25 mm
(1")
432 mm
(17")
25 mm
(1")
76 mm
(3")
310 cm
(48 in.2)
155 cm
(24 in.2)
2
2
Dimensions show recommended spacing allowed, except for
closet door ventilation openings which are minimum required.
This washer has been tested for installation with spacing of
0 mm (0") clearance on the sides. Consider allowing more space
for ease of installation and servicing, and spacing for companion
appliances and clearances for walls, doors, and oor moldings.
Add spacing of 25 mm (1") on all sides of washer to reduce
noise transfer. If a closet door or louvered door is installed,
top and bottom air openings in door are required.
See requirements for oor standpipe drain system.
Floor drain system
Floor drain system requires a Siphon Break Kit (Part Number
285834), 2 Connector Kits (Part Number 285385), and an
Extension Drain Hose (Part Number 285863) that may be
purchased separately. To order, contact your dealer.
Minimum siphon break: 710 mm (28") from bottom of washer.
(Additional hoses may be needed.)
Laundry tub drain system
Minimum capacity: 76 L (20 gal.). Top of laundry tub must be at
least 990 mm (39") above oor; install no higher than 2.44 m (96")
from bottom of washer.
IMPORTANT: To avoid siphoning, no more than 114 mm (4.5")
of drain hose should be inside standpipe or below the top of
wash tub. Secure drain hose with beaded tie strap.
4
Loading...