Because your life is getting busier and more complicated, Whirlpool washers are easy to use,
save time, and help you manage your home better. To ensure that you enjoy years of troublefree operation, we developed this Use and Care Guide. It contains valuable information about
how to operate and maintain your washer properly and safely. Please read it carefully.
Please record your model’s information.
Whenever you call to request service on
your appliance, you need to know your
complete model number and serial number.
You can find this information on the model
and serial number plate (see diagram on
page 4 for location of plate).
Please also record the purchase date of
your appliance and your dealer’s name,
address, and telephone number.
Keep this book and the sales slip together in a safe place for future reference.
Model Number ______________________
Serial Number ______________________
Purchase Date ______________________
Dealer Name _______________________
Dealer Address _____________________
Dealer Phone _______________________
2
Washer Safety
IMPORTANT SAFETY INSTRUCTIONS
WARNING
• Read all instructions before using your
washer.
• Do not machine wash or machine dry
items cleaned, washed, soaked in, or
spotted with wax, paint, gasoline, oil, or
other flammable fluids. The fumes can
create a fire hazard or explosion. Always
hand wash and line dry items containing
these materials.
• Flammable fluids (dry-cleaning solvents,
kerosene, gasoline, etc.) should not be
used or stored in or near your washer.
Do not add flammable fluids to your
wash water. These substances give off
vapors that can create a fire hazard or
explosion.
• Do not allow children to operate, play
with, or crawl on or inside your washer.
Supervise children closely when your
washer is used near them.
• Before your washer is removed from
service or discarded, remove the lid to
prevent accidental entrapment.
• After starting a cycle, do not reach
into the basket unless the Cycle
Control Knob is pushed in and all
motion stops.
• Do not tamper with the controls.
To reduce the risk of fire, electrical shock, or injury when using
your washer, follow basic precautions including the following:
• If your hot water has not been used
recently (usually 2 weeks or longer),
hydrogen gases may build up in your
water heater and your hot water
pipes. HYDROGEN GAS IS EXPLOSIVE. To prevent injury or damage,
before using your washer, turn on all hot
water faucets and allow water to run for
several minutes. This will allow gases to
escape. Do not smoke or use any open
flame near your faucet while it is open.
Please ...
• Have only a qualified person install,
repair, or replace parts on washer.
• Maintain washer properly.
• Protect washer from the weather and
keep it where the temperature will not fall
below freezing.
• Install and level washer on a floor that
can support the weight.
• Connect washer to the correct
3-prong outlet, electrical supply,
water supply, and drain.
• Ground washer properly.
†
See the Installation Instructions.
†
†
†
– SAVE THESE INSTRUCTIONS –
Understanding your responsibilities
• Store detergent, laundry aids, and other
materials in a cool, dry place where
children cannot reach them (in a locked
cabinet if possible).
• Read and follow instructions on pack-
ages of detergent and laundry aids,
especially warnings and precautions.
• Do not use chlorine bleach and ammo-
nia or acids (such as vinegar or rust
remover) in the same wash. Hazardous
fumes can form.
• Do not wash or dry items that are soiled
with vegetable or cooking oil. These items
may contain some oil after laundering. Due
to the remaining oil, the fabric may smoke
or catch fire by itself.
• Unplug power supply cord before attempt-
ing to service your washer.
• Do not machine wash fiberglass materials.
Small particles can stick to the fabrics
washed in following loads and cause skin
irritation.
3
Parts and Features
The parts and features of your washer are illustrated in this section. Become familiar with all
parts and features before using your washer.
Page references are included next to some features. Refer to those pages for more
information about the features.
Temperature
selector
(p. 5)
pin
S
Load size selector
(p. 5)
Agitator
Heavy DutyHeavy Duty
Ex-Small
Off
9
6
inse
R
OFFOFF
Regular
Permanent
Press
9
Normal
12
Heavy
Warm
Warm
Warm
Cold
Medium
Small
Load SizeLoad Size
Hot
Cold
ColdCold
Large
Wash
Rinse
Temperature
15
6
•
2 Speed
6 Cycle
Off
Super Wash
Off
9
Pull StartPull Start
Push StopPush Stop
3
9
Delicate
15
24
Off
Soak
Cycle control
knob
(p. 6)
Model and serial
number plate
(under lid)
(p. 2)
Basket
Tub
MAGIC CLEAN*
lint filter
(bottom of washer basket)
(p. 8)
4
Operating Your Washer
To obtain the best washing results, you must operate your washer properly. This section
gives you this important information. Page references are included should you desire more
information.
NOTE:Before using your washer, remove the consumer Features Guide from your washer
and place it with your Use and Care Guide.
Starting you washer
1. Add measured detergent to the
washer. Then place a sorted load of
clothes in the washer (see page 10).
2. Turn the Load Size Selector to the
setting that corresponds to the size of
the wash load and the type of fabric
being washed.
• Select a Small, Medium, or Large load size.
• To change the load size setting after the
washer has started to fill, turn the
Selector to the desired new setting.
• See pages 10-11 for loading tips.
Small
Medium
Large
3. Turn the Water Temperature Selector
to the desired wash-rinse temperature.
• Match the water temperature with the
type of fabric and soils being washed.
• The top temperature on the Selector is
the wash water and the bottom temperature is the rinse water.
• See page 12 for a water temperature
guide and additional information.
4. Push in and turn the Cycle Control
Knob clockwise. Stop when the indicator on the outer ring points to the
number in the wash cycle you want.
• The numbers are minutes of wash time.
• The cycles are described on page 6.
5. Pull out the Cycle Control Knob to
start the washer.
NOTES:
• To stop the washer at any time, push in
the Cycle Control Knob.
• To restart the washer, close lid (if neces-
sary) and pull out the Cycle Control Knob.
Warm
•
2 Speed
Cold
Super WashSuper Wash
Cold
10
Off
6
pin
S
Cool
Regular
Heavy
Down
inse
R
Pause
Permanent
Press
inse
R
pin
10
14
2
6
Off
S
Off
Pull Start
Push StopPush Stop
inse
R
pin
S
Off
Delicate
20
Soak
ColdHot
Cold
Warm
Cold
Hot
Cold
Cold
Cold
Wash
Rinse
Temperature
5 Cycle
5
OPERATING YOUR WASHER
Selecting a cycle and time
Use the information in this section to help you make the best cycle selections for your wash
loads. Each cycle is designed for different types of fabrics and soil levels.
• The washer pauses briefly throughout each cycle. These pauses are normal for washer operation.
• Refer to page 8 to help you understand what happens during a wash cycle.
Regular
Heavy
Super Wash
10
14
2
6
Off
Soak
R
inse
Super Wash cycle
Automatically prewashes the load and
advances into the REGULAR cycle (the
washer does not have to be reset after the
SUPER WASH cycle).
• Use the 6-minute cycle for heavily-soiled
loads that need maximum soil removal.
• Use the 2-minute cycle for moderately-
soiled loads that need extra soil removal.
NOTE:For proper cleaning, use double the
amount of detergent recommended for the
load size.
Regular cycle
Features the Gentle Wash system and high
spin speeds to shorten drying time.
• Use the 14-minute Heavy cycle to clean
sturdily-constructed cotton and linen fabrics
that are heavily soiled.
• Use 10 minutes of wash time to clean
sturdily-constructed cotton and linen fabrics
that are moderately soiled.
6
Spin
Off
10
6
Cool
Down
Pause
R
inse
Spin
Off
20
R
inse
Spin
Off
Delicate
Permanent
Press
Pull Start
Push Stop
Permanent Press cycle
Features the Gentle Wash system, a cooldown rinse, and low spin speeds to reduce
wrinkling.
• Use 6 to 10 minutes of wash time to clean
permanent press and some synthetic
fabrics that are lightly soiled to moderately
soiled.
Delicate cycle
Features a brief wash cycle and low spin
speeds to reduce wrinkling.
• Use this cycle to clean delicate items and
washable knits that are lightly soiled to
moderately soiled.
Soak cycle
Features brief periods of agitation and soak
time to help remove heavy soils and stains
that need pretreatment.
• Use up to 20 minutes of soak time,
depending on soil level.
• Use warm water when soaking laundry.
(Hot water can set stains.) See pages
14-16 for stain removal information.
• Use the amount of detergent or presoak
additive recommended by manufacturer.
• After the SOAK cycle ends, add detergent
and set a new wash cycle.
Using Rinse and Spin
When using extra detergent for heavily soiled
clothes, or washing special-care items, you
may want an extra rinse and spin.
1. Push the Cycle Control Knob in and turn
clockwise to RINSE, as illustrated.
2. Pull the Cycle Control Knob out. The
washer fills to selected load size, agitates,
drains, and spins.
Using Drain and Spin
A drain and spin may help shorten drying
times for some heavy fabrics or special-care
items by removing excess water.
1. Push the Cycle Control Knob in and
turn clockwise to SPIN, as illustrated.
2. Pull the Cycle Control Knob out. The
washer drains, then spins.
OPERATING YOUR WASHER
Super Wash
Super Wash
Regular
Off
Soak
Regular
Off
Soak
Off
Spin
R
inse
Off
Off
Spin
R
inse
Off
Permanent
Press
R
inse
Spin
Off
R
inse
Spin
Delicate
Permanent
Press
R
inse
Spin
Off
R
inse
Spin
Delicate
7
OPERATING YOUR WASHER
What happens in each cycle
When the Cycle Control Knob is set to a
number and pulled out, the washer fills (to the
selected load size) before agitation and timing
start. The washer will begin agitating immediately after filling; agitation can occur with the
washer lid up or down. After agitation starts,
the Cycle Control Knob turns clockwise until it
points to an OFF area and the cycle ends.
NOTE: A Gentle Wash system helps protect
your fabrics by reducing wash agitation
speed during the last few minutes of wash
agitation in the REGULAR and PERMANENT PRESS cycles.
WASH
Fill
▼
Wash selected time
Drain (or partial drain†)
†
The Permanent Press cycle partially
drains, fills, agitates briefly, and drains.
▼
No agitation
▼
Spin
▼
MAGIC CLEAN* lint filter
The lint filter at the bottom of the washer
basket cleans itself. During agitation, wash
and rinse water pass over the filter, separating the lint from the water. The lint is then
spun away from the filter and out of the
system during the spin part of the cycle.
If your washer drains into a tub, remove
any lint collected in the tub or strainer.
RINSE
Fill
▼
Rinse
▼
Drain-No agitation
▼
Spin-Spray rinse
▼
Spin
▼
Off
MAGIC CLEAN
lint filter
8
Basket
interior
Caring for Your Washer
Proper care of your washer can extend its life. This section explains how to care for your
washer properly and safely.
Cleaning your washer
Exterior
Wipe up detergent, bleach,
and other spills with a soft,
damp cloth or sponge as
they occur. Occasionally
wipe the outside of the
washer to keep it
looking like new.
Do not put sharp or metal
objects in your washer.
They can damage the
finish. Check all pockets for
pins, clips, money, bolts,
nuts, etc. Do not lay these
objects on your washer after emptying
pockets.
Interior
Clean interior with 250 mL (1 cup) of chlorine
bleach mixed with 500 mL (2 cups) of detergent. Run washer through a complete cycle
using hot water. Repeat process if necessary.
NOTE: Remove hard water deposits using
cleaners labeled as washer safe only.
Winter storage or moving care
Install and store your washer where it will not freeze. Because some water may stay in the
hoses, freezing can damage your washer. If storing or moving your washer during freezing
weather, winterize it.
To winterize washer:
1. Shut off both water faucets.
2. Disconnect and drain water inlet hoses.
3. Put 1L (1 quart) of R.V.-type antifreeze in
the basket.
4. Run washer on a drain and spin setting
(see page 7) for about 30 seconds to mix
the antifreeze and water.
5. Unplug the power supply cord.
To use washer again:
1. Flush water pipes and hoses.
2. Reconnect water inlet hoses.
3. Turn on both water faucets.
4. Reconnect power supply cord.
5. Run the washer through a complete cycle
with 250 mL (1 cup) of detergent to clean
out antifreeze.
Non-use or vacation care
You should operate your washer only when
you are at home. If you will be on vacation
or not using your washer for an extended
period of time, you should:
• Unplug the power supply cord or turn off
electrical power to the washer.
• Turn off the water supply to the washer.
This helps avoid accidental flooding (due
to a water pressure surge) while you are
away.
9
Laundry Tips
This section reviews proper laundering techniques and gives you additional washing information.
Preparing clothes for washing
• Close zippers, snaps, and hooks to avoid
snagging other items.
Remove pins, buckles, and
other hard objects to avoid
scratching the washer
interior. Remove nonwashable trim and ornaments.
• Empty pockets and turn them inside out.
• Turn down cuffs, brush away lint and dirt.
Sorting
• Separate heavily-soiled items from lightly-
soiled ones, even if they
would normally be washed
together. Separate lint
givers (towels, chenille)
from lint takers
(corduroy, synthetics,
• Turn synthetic knits inside out to avoid
pilling.
• Tie strings and sashes so they will not
tangle.
• Mend tears, loose hems, and seams.
• Treat spots and stains. (See “Removing
Stains” on page 14.)
• Stained or wet garments should be washed
promptly for best results.
permanent press). When possible, turn lint
givers inside out.
• Separate dark colors from light colors,
colorfast items from noncolorfast items.
• Sort by fabric and construction (sturdy
cottons, knits, delicate items).
Loading
• Drop items into washer loosely. Fill to the top
of the basket, but do not wrap
items around the agitator.
Items should move easily
through wash water for best cleaning and wrinkle-free results. Items
should sink and reappear later.
• Load washer properly and select correct load
size setting. Overloading or packing the
machine, and selecting a setting too small for
the wash load can:
– cause poor cleaning.
– increase wrinkling.
– create excessive lint.
– wear out items faster (because of pilling).
• Load by the amount of space items take
up, not by their weight.
• Mix large and small items in each load.
Load evenly to maintain
washer balance. An offbalance load can make the
washer vibrate during spin.
• Use a large load size setting to reduce
wrinkling with permanent press clothes and
some synthetic knits. These items should
have more room to move in the water than
heavy items (towels, jeans).
• Reduce wash time when using a small load
size setting. Loads with only a few small
items need less wash time.
10
LAUNDRY TIPS
Loading suggestions
For these suggested full-sized loads, set the Load Size Selector to the highest water level
setting.
loads. Use hot water only when washing
heavy, greasy soils or whites.
• Use cold rinses.
• Wash full loads.
• Use lower water levels when washing
small loads.
• Avoid rewashing. Use enough detergent
and pretreat stains or heavy soils. Use the
cycles and wash times recommended for
the fabric and soil.
• Use your washer during off-peak hours –
usually early morning and late evening.
(Ask your power company.)
11
LAUNDRY TIPS
Selecting a water temperature
Water temperature guide
WASH WATER
TEMPERATURE
HOT
130°F (54°C)
or above
WARM
90° – 110°F
(32° – 44°C)
COLD
70° – 90°F
(21° – 32°C)
†
The washer features cold rinses for all wash temperatures.
Checking hot water
temperature
Your hot water should be 130°F (54°C) or
above. If you do not know your hot water
temperature, you can check it easily. You
may need to raise the temperature of your
water heater.
To check your hot water temperature:
1. Fill a pan with the hottest water available
from the faucet that fills your washer.
NOTE: If you do not have a faucet at your
washer site, collect the water from the
faucet closest to your washer.
2. Place a candy thermometer or cooking
thermometer in the water to check the
temperature.
†
SUGGESTED FABRICS
• Work clothes
• Sturdy whites/colorfast
pastels
• Diapers
• Dark/noncolorfast colors
• Permanent press items
• Nylon, polyester, acrylics,
silks, woollens
• Knits/delicate fabrics
• Extra-sensitive colors
• Noncolorfast items
• Hand washables
COMMENTS
• Best cleaning for heavily-soiled items
• Removes oils, perspiration, greasy
• Prevents graying or yellowing
• Best for moderately-soiled to lightly-
• Safe for most fabric finishes
• Less fading and dye bleeding
• Reduces wrinkling
• Best for very lightly-soiled items
• Saves hot water
• Best rinse water temperature
Water hardness
Many poor washing results can be traced to
the hardness of the wash water. To check
your water hardness:
• City water – ask the city water company.
• Well water – ask the local water authority.
Ask for the mineral content in grains/gallon
or parts/million. If your water is more than
8 grains/gallon or more than 153 parts/
million, you should consider:
• Installing a water softener.
• Using more detergent.
• Using a packaged water conditioner.
• Not using soap.
soils and stains
soiled items
NOTE: In wash-water temperatures colder
than 70°F (21°C), detergents do not dissolve
well. Also, soils may be difficult to remove,
and some fabrics may retain wear wrinkles
and may have increased pilling.
12
LAUNDRY TIPS
Washing special-care items
Most garments and household textiles have care labels with laundering instructions. Always
follow care label directions when they are available. Below are general washing instruc-
tions for some special washables.
ITEM
Blankets
(electric or woollen)
Curtains, drapes,
slipcovers
Diapers
Elastic, spandex
Flame-retardant
clothing
Knits
CARE INSTRUCTIONS
Pretreat spots and stains. Select water temperature, cycle, and
time according to the type of blanket being washed. An extra
rinse may be necessary. Check care label to see if manufacturer
recommends machine washing.
Wash small loads. Crowding may cause wrinkling. Replace
slipcovers while still slightly damp. They will dry to fit tightly.
NOTE: Sun-damaged curtains and draperies will tear whether
hand or machine washed.
When using chlorine bleach for soaking, add extra detergent to
the load. Avoid overuse of fabric softeners – absorbency will be
reduced.
Elastic picks up oil from the body. Oil can damage elastic. Wash
often to reduce the damage. Use warm water and sufficient
detergent to remove oils. Do not use chlorine bleach.
Items will be clearly labeled as flame-retardant. Follow
manufacturer’s instructions to retain flame-retardant qualities.
Knits are comfortable to wear because they stretch. However,
this means that knits are more likely to be stretched and damaged when washed (especially bulky knits). Knits made of
synthetic fabrics such as polyester, nylon, and acrylic tend to
keep their original shape more than a knit made of cotton
or ramie.
Pillows, stuffed
toys
Plastic, rubber
items
Quilts, bedspreads
Scatter rugs
Snowsuits, jackets
Washing feather pillows is not recommended unless they will be
dried in a dryer.
Treat as delicate items. Wash in warm water. Wash small items
in a mesh bag.
Do not wash cotton-filled comforters unless they are quilted or
stitched. Tucked cotton batting tends to slip and become lumpy.
An extra rinse may be necessary.
Shake or vacuum rugs to remove loose dirt. Wash more than one
rug at a time. If washing only one rug, add bath towels to balance
the load.
Wash only one or two items at a time. You may need to stop the
washer occasionally to press air from the items being washed.
An extra rinse may be necessary.
13
Removing Stains
Stained, heavily-soiled or greasy items may need to be prewashed or soaked for best results.
Soaking helps remove protein-type stains like blood, milk, or grass. Prewashing helps loosen
soil before washing.
Stain removal rules
• Use warm water for soaking or prewashing
stained laundry. Hot water can set stains.
• Most stains are easier to remove when
they are fresh. Old or set stains may not
come out. Follow package directions for
pretreatment products.
• Before treating any stain, find out what
kind of stain it is, how old the stain is, what
kind of fabric it is, and if the fabric is
colorfast. (Check the care label.)
• Washing and drying can set some stains.
• Start with cold or warm water. Hot water
can set some stains.
Stain removal guide
STAIN
Alcoholic
beverage
Blood
TO REMOVE
These stains turn brown with age, so treat immediately. Sponge or soak
fresh stains with cold water. Wash. If stain remains, soak 15 minutes in a
solution of lukewarm water, liquid detergent, and a few drops of white
vinegar. Rinse. Wash.
Rinse immediately or soak in cold water with enzyme presoak for 30
minutes or longer. Rinse. Rub detergent into any remaining stains. Rinse.
If stain remains, put a few drops of 3% hydrogen peroxide on stain for
3-5 minutes. Rinse thoroughly. Wash.
• When bleach is recommended, use a bleach
that is safe for the fabric.
• Test stain removers on an inside seam or
hidden corner of the item to see if the color
is removed.
• Put the stained area face down on a paper
towel or white cloth. Apply the stain remover
to the back of the stain. This forces the stain
off the fabric instead of through it.
• Meat tenderizer or enzyme presoaks help
break down some protein stains so they are
easier to remove.
Chewing
gum
Chocolate
or coffee
Crayon and
candle wax
Cream,
milk, or
ice cream
14
Use ice to make gum hard. Scrape off what you can. Sponge with a
nonflammable fabric cleaner. Let dry. Wash.
Sponge immediately with a nonflammable fabric cleaner or apply a
prewash soil and stain remover. Rinse. Wash. If stain remains, apply a
liquid detergent to stain or soak in warm water with an enzyme presoak.
Rewash.
Scrape off excess with a dull knife. Place fabric between two blotters or
facial tissue. Press with warm iron. Remove color stain with nonflammable
fabric cleaner. Hand wash until stain is gone. If full load is crayon stained,
take to cleaners or coin-operated dry cleaning machine.
Sponge with a nonflammable fabric cleaner, or a prewash soil and stain
remover. Rinse. Wash. Repeat if necessary. If stain remains, apply a few
drops of liquid detergent and a few drops of ammonia. Blot dry and rinse.
If stain remains, soak in an enzyme presoak. Wash.
Loading...
+ 30 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.