Whirlpool 1CWTW4845EW, 7MWTW1950EW, 7MWTW1500EM, 7MWTW1805EM, 7MWTW1955EW Installation Instructions

...

WASHER INSTALLATION INSTRUCTIONS

INSTRUCCIONES DE INSTALACIÓN DE LA LAVADORA

Table of Contents Índice

WASHER SAFETY ..............................................................1

INSTALLATION REQUIREMENTS .....................................2

Tools and Parts ..................................................................... 2

Location Requirements .......................................................2

Drain System ........................................................................ 3

Electrical Requirements ......................................................4

INSTALLATION INSTRUCTIONS .......................................4

Before you start: remove shipping materials ....................4

Connect Drain Hose ............................................................. 5

Connect Inlet Hoses ............................................................. 6

Level Washer ........................................................................7

Complete Installation Checklist .......................................... 8

INSTALLATION NOTES

Date of purchase: _________________________________ Date of installation: _______________________________ Installer: ________________________________________ Model number: ___________________________________ Serial number: ___________________________________

SEGURIDAD DE LA LAVADORA .................................9

REQUISITOS DE INSTALACIÓN .................................9

Herramientas y piezas ...................................................9

Requisitos de ubicación ...............................................10

Sistema de desagüe ......................................................11

Requisitos eléctricos ....................................................11

INSTRUCCIONES DE INSTALACIÓN ........................12

Antes de comenzar: quite los materiales

de transporte .................................................................12

Conexión de la manguera de desagüe ........................ 13

Conexión de las mangueras de entrada .....................14

Nivelación de la lavadora .............................................15

Complete la instalación ...........................Contraportado

NOTAS SOBRE LA INSTALACIÓN

Fecha de compra: ________________________________ Fecha de instalación: ______________________________ Instalador: ______________________________________ Número de modelo: _______________________________ Número de serie: _________________________________

WASHER SAFETY

W10807862A

271/2"

INSTALLATION REQUIREMENTS

Tools and Parts

Gather required tools and parts before starting installation.

Tools needed:

Adjustable or open end wrench

Wood block

⁄

” (14 mm)

4" min

(102 mm)

Level

Ruler or measuring tape

Inlet hoses with flat washers

Rubber washer

Alternate parts: (Not supplied with washer)

Your installation may require additional parts.

If you have: You will need:

Overhead sewer Standard 20 gal. (76 L) 39" (990 mm) tall drain tub or utility sink, sump pump and connectors (available from local plumbing suppliers)

1" (25 mm) standpipe 2" (51 mm) diameter to 1" (25 mm) diameter Standpipe Adapter Part Number 3363920 Connector Kit Part Number 285835

Drain hose too short Extension Drain Hose Part Number 285863 Connector Kit Part Number 285835

Lint clogged drain Drain Protector Part Number 367031 Connector Kit Part Number 285835

Pliers that open to 13⁄4" (44.5 mm)

Optional tools:

Flashlight Bucket

Parts supplied:

NOTE: All parts supplied for installation are in

cardboard insert in the top of the washer.

Drain hose with clamp, U-form, and cable tie

“Y” connector

LOCATION REQUIREMENTS

Select proper location for your washer to improve performance and minimize noise and possible “washer walk”. Install your washer in a basement, laundry room, closet, or recessed area.

(699 mm)

42"

(1067 mm)

27"

(686 mm)

You will need:

4.5"

(114 mm)

A water heater set to 120° F (49° C).

A grounded electrical outlet located within 4 ft (1.2 m) of

power cord on back of washer.

Hot and cold water faucets located within 3 ft (0.9 m) of hot

and cold water ﬁll valves on washer and water pressure of 20-100 psi (138-690 kPa).

A level ﬂoor with maximum slope of 1" (25 mm) under entire

washer. Installing on carpet is not recommended.

Floor must support washer’s total weight (with water and load)

of 315 lbs (143 kgs).

IMPORTANT: Do not install, store, or operate washer where it will be exposed to weather or in temperatures below 32° F (0° C). Water remaining in washer after use may cause damage in low temperatures. See “Washer Care” in your Use and Care Guide for winterizing information.

Proper installation is your responsibility.

Recessed area or closet installation

(76 mm)

14" max.

(356 mm)

17"

(432 mm)

48 in.

(310 cm2)

DRAIN SYSTEM

Drain system can be installed using a ﬂoor drain, wall standpipe, ﬂoor standpipe, or laundry tub. Select method you need.

Floor standpipe drain system

39"

4.5"

(114 mm)

Minimum diameter for a standpipe drain: 2" (51 mm). Minimum carry-away capacity: 17 gal. (64 L) per minute. Top of standpipe must be at least 39" (990 mm) high; install no higher than 96" (2.44 m) from bottom of washer. If you must install higher than 96" (2.44 m), you will need a sump pump system.

Wall standpipe drain system

4.5"

(114 mm)

See requirements for ﬂoor standpipe drain system.

Floor drain system

(990 mm)

24 in.

(126 mm)

(25 mm)

(76 mm)

(155 cm2)

Dimensions show recommended spacing allowed, except for closet door ventilation openings which are minimum required. This washer has been tested for installation with spacing of 0" (0 mm) clearance on the sides. Consider allowing more space for ease of installation and servicing, and spacing for companion appliances and clearances for walls, doors, and ﬂoor moldings. Add spacing of 1" (25 mm) on all sides of washer to reduce noise transfer. If a closet door or louvered door is installed, top and bottom air openings in door are required.

Floor drain system requires a Siphon Break Kit (Part Number

285834), 2 Connector Kits (Part Number 285835), and an Extension Drain Hose (Part Number 285863) that may be purchased separately. Minimum siphon break: 28" (710 mm) from bottom of washer. (Additional hoses may be needed.)

Laundry tub drain system

39"

(990 mm)

Minimum capacity: 20 gal. (76 L). Top of laundry tub must be at least 39" (990 mm) above ﬂoor; install no higher than 96" (2.44 m) from bottom of washer.

IMPORTANT: To avoid siphoning, no more than 4.5" (114 mm) of drain hose should be inside standpipe or below the top of wash tub. Secure drain hose with cable tie.

ELECTRICAL REQUIREMENTS

A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical supply is required. A time-delay fuse or circuit breaker is recommended. It is recommended that a separate circuit breaker serving only this appliance be provided.

This washer is equipped with a power supply cord having

a 3 prong grounding plug.

To minimize possible shock hazard, the cord must be plugged

into a mating, 3 prong, grounding-type outlet, grounded in accordance with local codes and ordinances. If a mating outlet is not available, it is the personal responsibility and obligation of the customer to have the properly grounded outlet installed by a qualiﬁed electrician.

If codes permit and a separate ground wire is used, it is

recommended that a qualiﬁed electrician determine that the ground path is adequate.

Do not ground to a gas pipe.

Check with a qualiﬁed electrician if you are not sure the

washer is properly grounded.

Do not have a fuse in the neutral or ground circuit.

INSTALLATION INSTRUCTIONS

Before you start: remove shipping materials

It is necessary to remove all shipping materials for proper operation and to avoid excessive noise from washer.

1. Move washer

48"

(1.2 m)

Move washer to within 4 ft (1.2 m) of its ﬁnal location; it must be in a fully upright position.

NOTE: To avoid ﬂoor damage, set washer onto cardboard before moving it and make sure lid is taped shut.

2. Remove shipping base

To avoid damaging ﬂoor, place cardboard supports from shipping carton on ﬂoor behind washer. Tip washer back and place on cardboard supports. Remove shipping base. Set washer upright.

IMPORTANT: Removing shipping base is necessary for proper operation. If your washer includes a sound shield, please refer to the instructions included with the sound shield to install it at this time.

3. Remove packing tray from tub

Remove tape from washer lid, open lid and remove cardboard packing tray from tub. Be sure to remove all parts from tray.

NOTE: Keep tray in case you need to move washer later.

For a laundry tub or standpipe drain, go to step 6. For a ﬂoor drain, remove the preinstalled drain hose form as

shown in Step 7. You may need additional parts with separate directions. See “Tools and Parts”.

6. Place drain hose in standpipe

Drain hose form

4.5"

(114 mm)

4. Free power cord

Firmly grasp power cord plug and pull to free from rear panel. Gently place power cord over console to allow free access to back of washer.

CONNECT DRAIN HOSE

5. Attach drain hose to drain port

Place hose into standpipe (shown in picture) or over side of laundry tub.

IMPORTANT: 4.5" (114 mm) of drain hose should be inside standpipe; do not force excess hose into standpipe or lay on bottom of laundry tub. Drain hose form must be used.

7. Remove drain hose form

(ﬂoor drain installations only)

For ﬂoor drain installations, you will need to remove the drain hose form from the end of the drain hose. You may need additional parts with separate directions. See “Tools and Parts”.

Remove the red plastic plug from the black drain port on the back of the washer.

If clamp is not already in place on elbow end of drain hose, slide it over end as shown. Squeeze clamp with pliers and slide black elbow end of drain hose onto black drain port and secure with clamp.

+ 11 hidden pages