WG Security WGBTLFG User Manual

58Khz

Floor Guard

With Control Box

Installation Manual

Version: 2012

Manual Part Number: WG BTLFG IM

(120203A)

WG SECURITY PRODUCTS INC.

3031 Tisch Way, Suite 602, San Jose, CA 95128 (USA)

http://www.wgspi.com

“This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation.”

WG Security Products Inc. makes no representation or
warranty with respect to the contents hereof and
specifically disclaims any implied warranties of
merchantability or fitness for any particular purpose.
Further, WG Security Products Inc. reserves the right
to revise this publication and make changes from time
to time in the content hereof without obligation of WG
Security Products Inc. to notify any person of such
revision or changes.

WARRANTY DISCLAIMER

FCC ID: P9I-WGBTLFG

This equipment has been tested and found to comply with the limits for a class B
digital device, pursuant to Part 15 of the Federal Communications Commission (FCC)
rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:

‧ Reorient or relocate the receiving antenna.
‧ Increase the separation between the equipment and receiver.
‧ Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.
‧ Consult the dealer or an experienced radio/TV technician for help.

The use of a shielded-type power cord is required in order to meet FCC emission
limits and to prevent interference to the nearby radio and television reception. It is
essential that only the supplied power cord be used. Use only shielded cables to
connect I/O devices to this equipment. You are cautioned that changes or

modifications not expressly approved by the party responsible for compliance could
void your authority to operate the equipment.

Note:

Any changes or modifications not expressly approved by the grantee of this device
could void the user's authority to operate the equipment.

RF exposure warning

This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.This equipment must be installed and operated in
accordance with provided instructions and the antenna(s) used for this transmitter

Technical Support Contact Information

Tel: [phone]
North America
South America

Rest of World

As specified by FCC Regulations 15.21, any
changes or modifications not expressly approved
by the party responsible for compliance of this
equipment, will void the user’s permission and
authority to operate this equipment.

Toll Free: 888-633-5095

Fax: [phone]

Email: [e-mail]

Tel: 4+49 8654 7715-21

Fax: 4+49 8654 7715-21

Email: [e-mail]

CRITICAL NOTE

TABLE OF CONTENTS

OVERVIEW ............................................................................................................................... 5

SYSTEM OVERVIEW ................................................................................................................. 5

SYSTEM CONFIGURATION......................................................................................................... 2

FLOOR GUARD FEATURES & BENEFITS..................................................................................... 2

SPECIFICATIONS...................................................................................................................... 3

PRE-INSTALLATION INFORMATION..................................................................................... 4

FLOOR GUARD CONTROL UNIT DIMENSIONS............................................................................. 4

FLOOR GUARD ANTENNA DIMENSIONS ..................................................................................... 5

INSTALLATION ........................................................................................................................ 6

PARTS LIST –FLOOR GUARD OVERALL SYSTEM........................................................................ 6

QUICK START FOR SYSTEM CONNECTIONS ............................................................................... 7

INTERIOR CABLE AND CONNECTOR CONNECTIONS .................................................................... 8

POWER CORD NOTICES ........................................................................................................... 9

North American Power Supply Cords............................................................................... 9

International Power Supply Cord...................................................................................... 9

FUSE REPLACEMENT INFORMATION........................................................................................ 10



OVERVIEW

System Overview

Floor-Guard systems consist of one sealed floor antenna, a 58khz control unit and a smart
power supply unit (WG SPS-24). The control unit provides all the control functions for the
transceiver, including tag detection and alarm notification. The floor antenna is fully sealed
and water-proof and can be buried in concrete or cement floor.

Floor Guard Control Unit

WG-

Floor Antenna

( with ferrite antennas )

WG-

24vac Stepdown Transformer

WG SPS-24

Detection Range ( up from floor )

Super Pencil Tag 0.9 m 3 ft

Europe USA