Weston Pro 2300 User Manual

Download

If any components of this unit are broken, do not operate properly, or for product returns,

Phone: 1-800-814-4895 (Outside the U.S. 440-638-3131)

Mail: 20365 Progress Drive, Strongsville, Ohio 44149

E-Mail: CustomerService@WestonProducts.com

All Trademarks and Registered Trademarks are property of the respective companies.

ATTENTION!

pleas e conta ct Weston Products LLC

Web Site: WestonProducts.com

PRO-SERIES

SAVE THESE INSTRUCTIONS!

Refer to them often and use them to instruct others.

VACUUM

SEALER

PRO-2100

MODEL NO.

65-0101

PRO-2200

MODEL NO.

65-0801

PRO-2300

MODEL NO.

65-0201

US Patented

REV121112

7 / 10

Vacuum

Lid

Power Cord

Storage

WESTON WARRANTY INFORMATION

SAVE THIS WARRANTY INFORMATION FOR YOUR RECORDS!

Weston Products LLC warrants to the ORIGINAL RETAIL PURCHASER of this product that if operated in accordance with the printed instruction accompanying it, then for a period of 1 year from the date of purchase, the product shall be free from defects in material and workmanship. The Warranty Card, along with a copy of the original receipt, must be received by Weston Products LLC

within 30 days from purchase date for the warranty to apply. Failure to send the completely lled out Warranty

Card, along with a copy of the original receipt, will void the warranty. The product must be delivered to or shipped freight prepaid to Weston Products LLC for warranty services, in either its original packaging or similar packaging affording an equal degree of protection. Damage due to shipping is not the responsibility of the company. Weston Products LLC charges a $35.00 per hour bench charge. NOTE: No repairs will be started without the authorization of the customer. The return shipping cost to the customer will be added to the repair invoice. Weston Products LLC will repair (or at its discretion, replace) the product free of charge, if in the judgment of the company, it has been proven to be defective as to seller’s labor and material, within the warranty period.

O T S

R E

W O P

A E S

U U C

TA S

New or rebuilt replacements for factory defective parts will be supplied for one (1) year from the date of purchase. Replacement parts are warranted for the remainder of the original warranty period. For non-warranty repairs, contact Weston Products LLC’s Customer Service at 1-800-814-4895 M-F 8am-5pm EST (outside of the United States 440-638-3131) to obtain a Return Merchandise Authorization Number (RMA Number). Weston Products LLC will refuse all returns that do not contain this number. DO

NOT RETURN THE UNIT WITHOUT PROPER AUTHORIZATION FROM WESTON PRODUCTS LLC.

LIMITATIONS: The warranty is void if the product is used for any purpose other than that for which it is designed. The product must not have been previously altered, repaired, or serviced by anyone else other than Weston Products LLC. If applicable, the serial number must not have been altered or removed. The product must not have been subjected to accident in transit or while in the customer’s possession, misused, abused, or operated contrary to the instructions contained in the instruction manual. This includes failure caused by neglect of reasonable and necessary maintenance, improper line voltage and acts of nature. This warranty is not transferable and applies only to U.S. and Canadian sales. Except to the extent prohibited by applicable law, no other warranties whether expressed or implied,

including warranty merchantability and tness for a particular purpose, shall apply to this product. Under no

circumstances shall Weston Products LLC be liable for consequential damages sustained in connection with said product and Weston Products LLC neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than such as is expressly set forth herein. Any applicable implied warranties are also limited to the one (1) year period of the limited warranty.

This warranty covers only the product and its specic parts, not the food or other products processed in it.

CUT ALONG THE DOTTED LINE AND SEND THE WARRANTY CARD ALONG WITH A COPY OF YOUR ORIGINAL PURCHASE RECEIPT TO:

Weston Products LLC

20365 Progress Drive, Strongsville, OH 44149

6 / 11

Pro-Series Vacuum Sealer

Maintenance Kit Sold Separately

Model No. 08-0501-W

Power Cord Port

NOTE: The Vacuum Sealer is ONLY intended to be used with VACUUM BAGS. For best results, only use the recommended vacuum bags with an embossed or mesh lining. DO NOT USE HOUSEHOLD BAGS! Any other uses of the Vacuum Sealer, other than the uses described in this booklet, could potentially damage the appliance and void the warranty!

-2-

WESTON WARRANTY CARD

SEND THIS CARD ALONG WITH A COPY OF YOUR ORIGINAL PURCHASE RECEIPT TO:

WESTON WARRANTY, WESTON PRODUCTS LLC, 20365 PROGRESS DRIVE, STRONGSVILLE, OH 44149

Customer Name: _________________________________

Address: _______________________________________

City/State/Zip: ___________________________________

Telephone Number: (_________) ____________________

E-Mail Address: _________________________________

Original Date of Purchase: ______/________/________

Product Model #: _________________________________

Serial # (if applicable): ______________________

-15-

FOOD SAFETY

There are basic rules to follow when handling food.

They are COOK, SEPARATE, CLEAN, and CHILL.

COOK

It’s crucial to cook food to a safe internal temperature to destroy bacteria that is present. The safety of hamburgers and other foods made with ground meat has been receiving a lot of attention lately, and with good reason. When meat is ground, the bacteria present on the surface is mixed throughout the ground mixture. If this ground meat is not cooked to at least 160oF to 165oF (71oC to 74oC), bacteria will not be destroyed and there’s a good chance you will get sick.

Solid pieces of meat like steaks and chops don’t have dangerous bacteria like E. coli on the inside, so they can be served more rare. Still, any beef cut should be cooked to an internal temperature of at least 145oF (63oC) (medium rare). The safe temperature for poultry is 180oF (82oC) and solid cuts of pork should be cooked to 160oF (71oC). Eggs should be thoroughly cooked too. If you are making a meringue or other recipe that uses uncooked eggs, buy specially pasteurized eggs or use prepared meringue powder.

SEPARATE

Foods that will be eaten uncooked and foods that will be cooked before eating MUST ALWAYS be separated. Cross-contamination occurs when raw meats or eggs come in contact with foods that will be eaten uncooked. This is a major source of food poisoning. Always double-wrap raw meats and place them on the lowest shelf in the refrigerator so there is no way juices can drip onto fresh produce. Then use the raw meats within 1-2 days of purchase, or freeze for longer storage. Defrost frozen meats in the refrigerator, not on the counter.

When grilling or cooking raw meats or sh, make sure to place the cooked meat on a

clean platter. Don’t use the same platter you used to carry the food out to the grill. Wash the utensils used in grilling after the food is turned for the last time on the grill, as well as spatulas and spoons used for stir-frying or turning meat as it cooks.

COMPONENT LIST

DIAGRAM PART PART NO. DESCRIPTION NUMBER

1 Power Cord 08-0402

2 Power Indicator Switch 65-0110

3 Fuse Holder 08-0404

4 10-Amp Buss Fuse 08-0405

5 Rubber Foot (6) 08-0407

6 Seal Bar Heating Element with Screws 08-0427

7 Vacuum Lid Seal Bar Assembly 08-0430

8 Vacuum Lid Handle with Screws 08-0434

9 Internal Cooling Fan 08-0443

10 10mm Upper Seal Bar Tape 08-0425

11 15mm Lower Seal Bar Tape (2)* 08-0426 *NOTE one extra piece of Seal Bar Tape is included

with the original unit as a spare.

12 Oval Vacuum Chamber Seal (2) 08-0429

13 Maintenance Kit -Sold Separately 08-0501-W

(Includes 2 Oval Vacuum Chamber Seals,

(1) 10mm Upper Seal Bar Tape, (1) 15mm Lower Seal Bar Tape)

If any components of this unit are broken or the unit does not operate

Monday thru Friday 8:00am-5:00pm EST. Outside the U.S. call 440-638-3131

properly, call Weston Products LLC Toll Free at

1-800-814-4895

Make sure to wash your hands after handling raw meats or raw eggs. Washing hands with soap and water, or using a pre-moistened antibacterial towelette is absolutely necessary after you have touched raw meat or raw eggs. Not washing hands and surfaces while cooking is a major cause of cross-contamination.

CLEAN

Wash your hands and work surfaces frequently when you are cooking. Washing with soap and warm water for at least 15 seconds, then dry with a paper towel.

CHILL

Chilling food is very important. The danger zone where bacteria multiply is between 40oF and 140oF (4oC and 6oC). Your refrigerator should be set to 40oF (4oC) or below; your freezer should be 0oF (-17oC) or below. Simple rule: serve hot foods hot, cold foods

cold. Use chang dishes or hot plates to keep food hot while serving. Use ice water

baths to keep cold foods cold. Never let any food sit at room temperature for more than 2 hours - 1 hour if the ambient temperature is 90oF (32oC) or above. When packing for a picnic, make sure the foods are already chilled when they go into the insulated hamper. The hamper won’t chill food - it just keeps food cold when properly packed with ice. Hot cooked foods should be placed in shallow containers and immediately refrigerated so they cool rapidly. Make sure to cover foods after they are cool.

NOTE: Special considerations must be made when using venison or other wild game,

since it can become heavily contaminated during eld dressing. Venison is often held

at temperatures that could potentially allow bacteria to grow, such as when it is being transported. Refer to the USDA Meat and Poultry Department for further questions or information on meat and food safety.

-14-

ADDITIONAL ACCESSORIES AVAILABLE

Pint 6” x 10” 100 Count Vacuum Bags 30-0106-W Quart 8” x 12” 100 Count Vacuum Bags 30-0101-W Gallon 11” x 16” 100 Count Vacuum Bags 30-0102-W Extra Large 15” x 18” 100 Count Vacuum Bags 30-0105-W (3 Rolls) 8” x 22’ Rolls Vacuum Bags 30-0201-W (3 Rolls) 11” x 18’ Rolls Vacuum Bags 30-0202-W Multi-Pack Vacuum Bags 50 Count 30-0107-W

These products and many more products can be ordered by visiting

Monday thru Friday 8:00am-5:00pm EST. Outside the U.S. call 440-638-3131

WestonSupply.com or by calling

Weston Products LLC Toll Free at 1-800-814-4895

-3-

WARNING! Before cleaning, assembling or disassembling the Vacuum

Sealer, make sure the Vacuum Sealer is OFF and the PLUG IS REMOVED FROM THE OUTLET/POWER SOURCE!

IMPORTANT SAFETY RULES

READ AND FULLY UNDERSTAND ALL INSTRUCTIONS AND WARNINGS PRIOR TO USING THIS UNIT. YOUR SAFETY IS MOST IMPORTANT! FAILURE TO COMPLY WITH PROCEDURES AND SAFEGUARDS MAY RESULT

WARNING!

1. ALWAYS DISCONNECT Vacuum Sealer from power source before servicing, changing accessories or cleaning the unit.

2. Plug the Vacuum Sealer into a standard 120 Volt, 60 Hz wall outlet. Avoid using extension cords.

3. DO NOT USE the Vacuum Sealer if the Power Cord, Plug or any other parts are damaged. If the Power Cord or the Vacuum

Sealer is damaged, call Customer Service. DO NOT ATTEMPT TO REPLACE THE CORD.

Be sure to not allow the Power Cord to drape into your work area. Check that all parts are operating properly, and perform the intended functions. Check for any other conditions that may affect the operation.

4. NEVER use any accessories or parts from other manufacturers. Doing so will VOID YOUR

WARRANTY and may cause re, electrical

shock or injury.

5. Reduce risk of unintentional starting. Make sure the Power Switch is in the “OFF” position before attaching to the power source.

6. KEEP FINGERS CLEAR of the Heat Sealing Bar and Seal Bar Tape AT ALL TIMES, these areas become HOT. Doing so

may cause serious injury.

7. DO NOT take this appliance apart; doing so will VOID YOUR WARRANTY and may result in personal injury.

SAVE THESE INSTRUCTIONS!

IN SERIOUS INJURY OR PROPERTY DAMAGE.

REMEMBER: YOUR PERSONAL SAFETY IS YOUR RESPONSIBILITY!

8. TO PROTECT AGAINST RISK OF ELECTRICAL SHOCK: DO NOT SUBMERGE THE VACUUM SEALER INTO WATER OR LIQUID. BE SURE THE VACUUM SEALER IS DISCONNECTED FROM THE POWER SOURCE BEFORE CLEANING. Follow the “Cleaning Instructions” in this booklet. NEVER rinse appliance Vacuum Sealer under tap.

9. NEVER LEAVE THE VACUUM SEALER

UNATTENDED. Be safe, DISCONNECT the Vacuum Sealer from power source before

leaving the work area. Close supervision is necessary when any appliance is used near children. This appliance is NOT to be used by children.

10. DO NOT let the Power Cord hang over edge of work surface.

11. Be sure the Vacuum Sealer is on a stable work surface. Be sure all the Vacuum Sealer Feet are stable.

12. DO NOT use the Vacuum Sealer outdoors.

13. DO NOT use the Vacuum Sealer while

under the inuence of drugs, medications or

alcohol.

14. The Vacuum Sealer is ONLY intended

to be used with VACUUM BAGS. For best results, only use the recommended vacuum bags. DO NOT USE HOUSEHOLD

BAGS! Any other uses of the Vacuum Sealer, other than the uses described in

this booklet, could potentially damage the appliance and void the warranty!

Refer to them often and use them to instruct others.

VACUUM PACKAGING GUIDELINES

Very Moist Foods: It is best to freeze very moist food items, like sh, before vacuum

sealing them. The excessive moisture can interfere with the Sealing Bar’s ability to completely fuse the layers of the bag together.

Powdery Items: When vacuum sealing powdery items, like our, it is best to keep them in their original packaging before putting them into the vacuum bags. The ne

powder may get sucked into the 2-Piston Vacuum Pump and cause enough damage to shorten the life of your Vacuum Sealer. Powdery items may also interfere with the bag sealing function.

Sharp or Pointed Items: When vacuum sealing sharp or pointy items, it is best to cushion the edges so they do not puncture the bag during the vacuum process.

YEAST & BACTERIA

For best results in extending the life of foods, it is important to vacuum package foods that are fresh. Once food has begun to deteriorate, vacuum packaging may only slow the deterioration process. Vacuum sealing cannot completely prevent the growth of mold. Other disease causing microorganisms can still grow in low oxygen environments and may require further measures to be eliminated.

Yeast: The development of yeast can be slowed by refrigeration and completely stopped by freezing food at 0oF (-18oC). Yeast causes fermentation, which will give food

an identiable smell.

Bacteria: Freezing cannot eliminate bacteria, but their growth can be stopped. The

growth of bacteria can be easily identied by an offensive odor and sometimes a slimy

texture. Some bacteria, like the one that causes botulism, can grow in low oxygen environments and cannot be detected by smell, taste or color. Botulism is very rare, but dangerous. Be sure that all foods are stored and cooked properly before eating.

COOKING & HEATING

Before microwaving vacuum-packed foods, puncture or open the bag to allow hot air

to escape while heating.

Vacuum-packed foods can be thawed or cooked in boiling water.

Vacuum-packed perishable foods like meats, vegetables and cheeses must

be refrigerated (at or below 34oF (1.1oC)) or frozen, especially acid-free or low-acid foods.

This is important because although vacuum packaging removes most air from the bag, bacteria like Clostridium Botulinum, which produces a toxin that causes the illness botulism, is anaerobic and grows in the absence of oxygen. Refrigeration and freezing slow the growth of bacteria. It is also important to maintain a clean working area to reduce the likelihood of packaging harmful bacteria with the food.

NOTE: The Vacuum Sealer is ONLY intended to be used with VACUUM BAGS. For best results, only use the recommended vacuum bags. DO NOT USE HOUSEHOLD BAGS! Any other uses of the Vacuum Sealer, other than the uses described in this booklet, could potentially damage the appliance and void the warranty!

-4- -13-

STORAGE LIFESPAN GUIDELINES

IMPORTANT NOTE: Vacuum packaging is NOT a substitute for refrigeration.

Vacuum packed perishable foods still require refrigeration.

NEVER thaw frozen foods at room temperature. Thaw frozen foods in a refrigerator

or microwave oven.

In general, the colder the temperature at which foods are stored, the longer the

shelf life.

Handle vacuum sealer bags with care. Avoid damaging them. A damaged bag

will not hold a seal.

Only use information in the following chart as a guideline! Refer to the “Vacuum Packaging Guidelines” and “Food Safety” sections of this manual. Actual storage life spans may vary. Check all food for spoilage before use.

PROTECTIVE TAPE

There are two (2) factory installed

strips of Seal Bar Tape on the Vacuum Sealer.

DO NOT REMOVE THE TAPE!

Figure 1

FOOD STORAGE NORMAL VACUUM

TYPE LOCATION LIFE PACKED LIFE

LARGE CUTS OF MEAT Freezer 6 months 2-3 years GROUND MEAT Freezer 4 months 1 year FISH Freezer 6 months 2 years

For best results, freeze meats & sh for 1-2 hours before vacuum packing to help prevent moisture

COFFEE BEANS Room temperature 4 weeks 16 months COFFEE BEANS Freezer 6-9 months 2-3 years FLOUR, RICE, SUGAR Room Temperature 6 months 1-2 years

For best results, powder or grainy substances should be kept in their original container or bag, then placed in a

BERRIES strawberries, raspberries, blackberries Refrigerator 1-3 days 1 week BERRIES cranberries, huckleberries, blueberries Refrigerator 3-6 days 2 weeks

To prevent berries from being crushed by the vacuum sealer, it is best to freeze item before packing. Spread the berries out on a

cookie sheet to allow them to freeze individually. Berries frozen in a large block will be difcult to vacuum seal due to the

CHEESE Refrigerator 1-2 weeks 4-8 months

If vacuum packed cheese is used often, make sure the vacuum bag is long enough to allow for repeated sealing. For shredded

cheese, place a paper towel inside the vacuum bag, on top of the cheese to prevent the cheese from being

COOKIES, CRACKERS, BREADS with periodical opening Room Temperature 1-2 weeks 3-6 weeks

PASTA, GRAINS, DRIED BEANS Room Temperature 6 months 1-1/2 years NUTS Room Temperature 6 months 2 years

Dried foods with sharp edges should be wrapped in a paper towel or other matter to prevent the sharp edges from puncturing the vacuum bag.

LETTUCE Refrigerator 3-6 days 2 weeks

VEGETABLES Freezer 8 months 2 1/2 years

To maximize the taste of vegetables, blanch them before vacuum packaging. Blanching cooks the vegetables very briey, sealing

in the avor, color and texture, leaving the vegetables cooked but still crisp. Vegetables can be blanched in boiling water in the microwave,

most vegetables only require 2-3 minutes (corn on the cob requires 6-11 minutes). Then immerse the vegetables in cold water to

and juices from interfering with the seal of the vacuum bag.

vacuum bag for sealing to prevent interfering with the seal of the vacuum bag.

many small air pockets that would form between the berries.

sucked into the Vacuum Sealer or interfering with the sealing of the bag.

Freeze soft airy foods for 1-2 hours prior vacuum packing, to retain shape & texture.

Wash & thoroughly dry leafy vegetables before vacuum packaging.

stop the cooking process. Dry the vegetables, then vacuum pack.

Table adapted from Dr. G.K.York, Dept. of Food Science & Tech, U of California, Davis.

SEAL BAR TAPE

DO NOT

REMOVE!

OVAL VACUUM CHAMBER SEALS

DO NOT REMOVE!

The Seal Bar Heating Element and Vacuum Lid Seal are each covered with Seal Bar Tape to protect vacuum bags during sealing Figure 1. DO NOT remove the Seal Bar Tape. See the “Service Instructions” section of this manual for information on replacing the Seal Bar Tape, if necessary.

*NOTE one extra piece of Seal Bar Tape is included with the original unit as a spare.

CLEANING INSTRUCTIONS

WARNING! Before cleaning, assembling or disassembling the Vacuum

Sealer, make sure the Vacuum Sealer is OFF and the PLUG IS REMOVED FROM THE OUTLET/POWER SOURCE!

NEVER IMMERSE the Vacuum Sealer in water or other liquid.

Make sure the Vacuum Sealer has completely cooled before cleaning it.

Wipe clean all outside surfaces including the Plastic Vacuum Chamber and

Vacuum Lid with a damp cloth or paper towel. Most household spray cleaners are safe to use. Avoid spraying directly into the vent on the left side of the unit. DO NOT use abrasive cleansers! Abrasive cleansers will spoil the clarity of the Vacuum Lid.

Be careful while cleaning not to peel or damage the strips of Seal Bar Tape

covering the Seal Bar Heating Element and Vacuum Lid Seal.

Dry all surfaces and close the Vacuum Lid before storing the Vacuum Sealer.

-12-

-5-

VACUUM CHAMBER SEALS

There are two factory-installed Oval Vacuum Chamber Seals on the Vacuum Sealer. When the Vacuum Lid is closed and downward force applied, they form an

airtight seal so the Vacuum Chamber can be evacuated.

6. Set a new Oval Vacuum Chamber Seal on the groove in the Plastic Vacuum Chamber. Work the seal into the groove.

7. Position a new Oval Vacuum Chamber Seal near the groove in the Vacuum Lid. Work the seal into the groove.

The Oval Vacuum Chamber Seals may wear over time and require replacement. See the “Service Instructions” section of this manual for information on replacing the Oval Vacuum Chamber Seals, if necessary.

COOLING FAN

The Vacuum Sealer has an Internal Cooling Fan that runs whenever the unit is plugged in and turned on. To save energy, turn the unit “OFF” and unplug the Power Cord when not in use.

THERMAL OVERLOAD PROTECTOR

The Vacuum Sealer will automatically shut down if it overheats. If this occurs, turn the unit off and open the Vacuum Lid. Resume normal operation after the unit cools about 20 minutes.

To help prevent overheating, wait at least 20 seconds between cycles with the Vacuum Lid open. Avoid touching the Seal Bar Tape. The Seal Bar Tape will remain hot for a brief period of time after each sealing cycle.

LIMIT SWITCH

The Vacuum Sealer is equipped with a switch to prevent actuation of the Seal Bar Heating Element in manual mode when the Vacuum Lid is open. When the Vacuum Lid is closed, heat made by the Seal Bar Heating Element is absorbed by the vacuum bag and Vacuum Lid Seal.

REPLACING THE SEAL BAR TAPE:

*NOTE one extra piece of Seal Bar Tape is included with the original unit as a spare.

1. Turn “OFF” the Vacuum Sealer and remove the Power Cord from the electrical outlet.

2. Make sure the unit is completely cool.

3. Open the Vacuum Lid.

4. Pick at either end of the Seal Bar Tape covering the Seal Bar Heating Element until it lifts slightly. Grasp the loose end and slowly pull the Seal Bar Tape back over itself until fully removed.

5. Repeat step 4 for the Seal Bar Tape covering Vacuum Lid Seal. DO NOT remove the Seal.

6. Remove the backing from a new wide strip of Seal Bar Tape for the Seal Bar Heating Element. Be careful not to allow the Seal Bar Tape to contact anything including itself while the adhesive side is exposed.

7. Hold one end of the Seal Bar Tape in each hand. Stick the left end of the Seal Bar

Tape to the at area on the Plastic Vacuum Chamber just left of the Seal Bar Heating Element. Apply the Seal Bar Tape from left to right over the Seal Bar Heating Element

until done. Make sure there are no wrinkles or folds in the Seal Bar Tape once applied. The Seal Bar Tape should fully cover the Seal Bar Heating Element.

8. Remove the backing from a new narrow strip of Seal Bar Tape for the Vacuum Lid

Seal. Stick the left end of the Seal Bar Tape onto the left end of the Seal. The Seal Bar Tape and Seal ends should be ush. Apply the Seal Bar Tape from left to right over the Vacuum Lid Seal until done. Make sure there are no wrinkles or folds in the Seal Bar Tape once applied. The Seal Bar Tape should fully cover the Vacuum Lid Seal.

When the Vacuum Lid is open, there is no means to dissipate the heat and unit damage may occur.

-6-

REPLACING THE FUSE

If the Vacuum Sealer does not operate when it is plugged in and turned on, try any or all of the following:

1. Make sure the Fuse is not blown. The Fuse is located on the right side of the unit directly above the Power Cord Port. Turn “OFF” and unplug the Vacuum Sealer. Twist off and remove the Fuse Cap. Remove and check the Fuse. The thin metal band in the center of the Fuse should be clean and unbroken. If it is burned and/or broken, replace it with a new Fuse (10 Amp). Replace the Fuse Cap.

2. Make sure the Connector at the end of the Power Cord is plugged completely into the Power Cord Port.

3. Make sure the Power Cord is not damaged. DO NOT use a damaged Power Cord. Call the Customer Service line for information on part replacement.

4. Try connecting the Power Cord Plug to another electrical outlet.

-11-

Figure 5

PREPARING VAC BAGS FROM A ROLL

1. Make sure the Vacuum Sealer is in the “OFF” position. Attach the Vacuum Sealer to the power supply.

2. Turn the Vacuum Sealer “ON”.

3. The “POWER” Light on the display, “POWER INDICATOR” Switch both will illuminate and the Internal Cooling Fan will run.

4. Open the Vacuum Lid.

5. Cut a vacuum bag to the length you want from a roll.

6. Place either open end of the bag against the outer face of the Oval Vacuum Chamber Seal in the Vacuum Chamber (not in the Vacuum Chamber).

GROUNDING INSTRUCTIONS

GROUNDING

This appliance must be grounded while in use to protect the operator from electrical shock. The appliance is equipped with a 3-conductor cord and a 3-prong

grounding type plug to t the proper grounding-type

receptacle. The appliance has a plug that looks like Figure A. An adaptor, Figure B, should be used for connecting Figure A plugs to two-prong receptacles. The grounding tab which extends from the adaptor must be connected to a permanent ground such as a properly grounded outlet box as shown in Figure C using a metal screw.

Grounding

Prong

Circuit Grounding Conductor

Figure A

Figure B

7. Close the Vacuum Lid. The bag end should be sandwiched between the Vacuum Lid Seal and Seal Bar Heating Element. Make sure there are no wrinkles or creases

in the bag in the sealing area.

8. Press and hold the Vacuum Lid Handle down. You may need to continue holding the bag.

9. Press the “START” Button (this will engage the Pump and the Heating Element).

Press the Manual Seal Button to seal the vacuum bag.

10. Sealing is complete when the Vacuum Chamber releases after a 3 second cooling period (the “COOL” Light will illuminate). The release is audible.

11. Open the Vacuum Lid and remove the bag. DO NOT try to open the Vacuum Lid before the vacuum has released or unit damage may occur. Wait at least 20 seconds before sealing another bag to avoid overheating the unit.

12. Turn the Vacuum Sealer “OFF” and unplug the Power Cord when you are done.

SERVICE INSTRUCTIONS

WARNING! Before cleaning, assembling or disassembling the Vacuum

Sealer, make sure the Vacuum Sealer is OFF and the PLUG IS REMOVED FROM THE OUTLET/POWER SOURCE!

Some parts of the Vacuum Sealer may need replacing after repeated use. A Vacuum Sealer Maintenance Kit (Sold Separately Model No. 08-0501-W) may be necessary for the

Vacuum Sealer to properly function.

REPLACING THE OVAL VACUUM CHAMBER SEALS:

1. Turn “OFF” the Vacuum Sealer and remove the Power Cord from the electrical outlet.

2. Make sure the unit is completely cool.

EXTENSION CORDS

Use only 3-wire extension cords which have 3-prong grounding-type plugs and a 3-pole cord connector that accepts the plug from the appliance. Use only extension cords having an electrical rating not less than the rating of the appliance. Do not use damaged extension cords. Examine extension cord before using

Grounded

Outlet Box

and replace if damaged. Do not abuse extension cord and do not yank on any cord to disconnect. Keep cord away from heat and sharp edges.

POWER SUPPLY

Insert the connector end of the Power Cord into the Power Cord Port on the right side of the unit. Insert

the Plug on the Power Cord into a standard 120-volt grounded electrical outlet Figure 2. DO NOT modify the plug to t an unsuitable outlet.

Metal

Grounding

Screw

Cover of

Grounding

Means

AA2220

Power Cord

Figure 2

Power

Indicator

Switch

Port

Figure C

Connector

End

3. Open the Vacuum Lid.

4. Remove the Oval Vacuum Chamber Seal from the groove on the underside of the Vacuum Lid.

5. Remove the Oval Vacuum Chamber Seal from the groove in the Plastic Vacuum Chamber.

Plug End

Power

Cord

-7--10-

CONTROL BUTTONS

5. Fill a vacuum bag with the product you want to seal. Leave at least 2” (5 cm) of space between the open end of the bag and product Figure 4.

STOP BUTTON

Press the Stop Button stops to halt the vacuuming process Figure 3.

MANUAL SEAL BUTTON

Press the Manual Seal Button during the vacuuming process to initiate the seal (before the preset vacuum pressure is reached) Figure 3.

START BUTTON

Press the Start Button to initiate the vacuuming process (the Vacuum Sealer will automatically seal the bag when a preset vacuum pressure is reached) Figure 3.

Figure 3

OPERATING INSTRUCTIONS

WARNING! Before cleaning, assembling or disassembling the Vacuum

Sealer, make sure the Vacuum Sealer is OFF and the PLUG IS REMOVED FROM THE OUTLET/POWER SOURCE!

CAUTION: The Seal Bar Heating Element and Vacuum Lid Seal get HOT! Avoid

touching them. Be careful while loading bags into the Vacuum Chamber.

DO NOT try to open the Vacuum Lid before the vacuum has released or unit

damage may occur.

Wait at least 20 seconds between cycles to avoid overheating the unit.

DO NOT allow liquids, powder or other small substances to be sucked into the Vacuum Port or unit damage may occur. Press the “Stop” Button to hault the vacuum process. Use the “Manual Seal” Button when vacuum sealing liquids.

The Vacuum Sealer is ONLY intended to be used with VACUUM BAGS. For best results, only use the recommended vacuum bags. DO NOT USE HOUSEHOLD BAGS! Any other uses of the Vacuum Sealer, other than the uses described in this booklet, could potentially damage the appliance and void the warranty.

1. Make sure the Vacuum Sealer is in the “OFF” position. Attach the Vacuum Sealer to the power supply.

6. Load the open end of the bag into the Lower Vacuum Chamber. Center the bag in the Lower Vacuum Chamber. Place the bag close to, but do not cover, the Vacuum Port. Be careful not to touch either strip of Seal Bar Tape which may be HOT from a previous heating cycle.

7. Close the Vacuum Lid. Make sure there are no folds or creases in the bag in the sealing area.

8. Press down on the Vacuum Lid Handle to form a tight seal.

9. Press the “START” Button to initiate the vacuuming process (the “VACUUM” Light will illuminate). Release the Vacuum Lid Handle at the rst sign of bag collapse. The Vacuum Sealer will automatically seal the bag when a preset vacuum pressure is reached in the Vacuum Chamber. Sealing lasts for 3 seconds (the “SEAL” Light will illuminate).

10. To manually seal a bag press the Manual Seal Button at any time during the vacuuming process.

11. You can stop the vacuuming process at any time by pressing the “STOP” Button.

12. Sealing is complete when the Vacuum Chamber releases after a 3 second cooling period (the “COOL” Light will illuminate). The release is audible.

13. Open the Vacuum Lid and remove the bag. DO NOT try to open the Vacuum Lid before the vacuum has released or unit damage may occur. Wait at least 20 seconds before sealing another bag to avoid overheating the unit.

14. Turn the Vacuum Sealer “OFF” and unplug the Power Cord when you are done.

Figure 4

Leave 2”

(5 cm)

Space

Vacuum

Port

Bag in Center of

Vacuum Chamber

2. Turn the Vacuum Sealer “ON”.

3. The “POWER” Light on the display, “POWER INDICATOR” Switch both will illuminate and the Internal Cooling Fan will run.

4. Open the Vacuum Lid.

-8- -9-

Weston Pro 2300 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual