For the online catalog, log onto www.westonsupply.com.
Exc lusiv ely impo rte d by Pra gotra de LLC S tro ngsvi lle , Ohi o
www.pragotrade.com
MEAT
CUBER/TENDERIZER
GRINDER ATTACHMENT
MODEL # 07-3201-W-A
Grinder Not Included
REV031709
MEAT CUBER/TENDERIZER
GRINDER ATTACHMENT
MODEL # 07-3201-W-A
COMPONENT LIST
DIAGRAM NO. PART DESCRIPTION PART NO.
1 Lower Housing 07-3184-A
2 Top Housing 07-3181-A
3 Shaft Adapter 07-3213
4 Blade Rack Assembly 07-3103
5 Left Comb 07-3119
6 Right Comb 07-3118
7 Housing Thumbscrews (2) 07-3166
8 Electric Grinder Adapter 07-3202
9 Chute 07-3182-A
10 Shaft Adapter Set Screw 07-3187
11 Adapter Mounting Bolt (2) 07-3188
12 Stainless Steel Tongs 07-3151
13 Nylon Bushing 07-3127
14 Screw & Lock Washers for Chute (2) 07-3183
15 Allen Wrench for Set Screws 07-3186
16 Allen Wrench for Chute/Adapter 07-3178
17 Shaft Clip (2) 07-3165
WARRANTY INFORMATION
SAVE THIS WARRANTY INFORMATION FOR YOUR RECORDS!
Pragotrade LLC warrants to the ORIGINAL RETAIL PURCHASER of this product that if operated in accordance
with the printed instruction accompanying it, then for a period of 1 year from the date of purchase, the product shall be
free from defects in material and workmanship.
The Warranty Card, along with a copy of the original receipt, must be received by Pragotrade LLC within 30 days
from purchase date for the warranty to apply. Failure to send the completely lled out Warranty Card, along with a copy
of the original receipt, will void the warranty.
The product must be delivered to or shipped freight prepaid to Pragotrade LLC for warranty services, in either its
original packaging or similar packaging affording an equal degree of protection. Damage due to shipping is not the
responsibility of the company. Pragotrade LLC charges a $35.00 per hour bench charge. NOTE: No repairs will be
started without the authorization of the customer. The return shipping cost to the customer will be added to the repair
invoice.
Pragotrade LLC will repair (or at its discretion, replace) the product free of charge, if in the judgment of the company,
it has been proven to be defective as to seller’s labor and material, within the warranty period.
New or rebuilt replacements for factory defective parts will be supplied for one (1) year from the date of purchase.
Replacement parts are warranted for the remainder of the original warranty period.
For non-warranty repairs, contact Pragotrade’s Customer Service at 1-800-814-4895 M-F 8am-5pm EST (outside of
the United States 440-638-3131) to obtain a Return Authorization Number (RMA Number). Pragotrade will refuse all
returns that do not contain this number. DO NOT RETURN THE UNIT WITHOUT PROPER AUTHORIZATION
FROM PRAGOTRADE LLC.
LIMITATIONS: The warranty is void if the product is used for any purpose other than that for which it is designed.
The product must not have been previously altered, repaired, or serviced by anyone else other than Pragotrade LLC.
If applicable, the serial number must not have been altered or removed. The product must not have been subjected
to accident in transit or while in the customer’s possession, misused, abused, or operated contrary to the instructions
contained in the instruction manual. This includes failure caused by neglect of reasonable and necessary maintenance,
improper line voltage and acts of nature. This warranty is not transferable and applies only to U.S. and Canadian
sales.
Except to the extent prohibited by applicable law, no other warranties whether expressed or implied, including
warranty merchantability and tness for a particular purpose, shall apply to this product. Under no circumstances shall
Pragotrade LLC be liable for consequential damages sustained in connection with said product and Pragotrade LLC
neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than
such as is expressly set forth herein. Any applicable implied warranties are also limited to the one (1) year period of
the limited warranty.
This warranty covers only the product and its specic parts, not the food or other products processed in it.
CUT ALONG THE DOTTED LINE AND SEND THE WARRANTY CARD ALONG WITH A
COPY OF YOUR ORIGINAL PURCHASE RECEIPT TO:
20365 Progress Drive, Strongsville, OH 44149
Pragotrade LLC
If an y compo ne nts of th is un it are br ok en or t he unit d oes n ot operat e
prope rl y, ca ll Pragot ra de LL C Toll Free at
1-800-814-4895
Monday thru Friday 8:00am-5:00pm EST.
Outside the U.S. call 440-638-3131
-2-
WARRANTY CARD
SEND THIS CARD ALONG WITH A COPY OF YOUR ORIGINAL PURCHASE RECEIPT
Original Date of Purchase: _______/_________/__________
Product Model #: __________________________________
Serial # (if applicable): ____________________________
-11-
CLEARING A JAM
WARNING! Before cleaning, assembling or disassembling the Cuber/
Tenderizer Attachment make sure the PLUG of the GRINDER IS REMOVED
FROM THE OUTLET/POWER SOURCE! ALWAYS unplug the grinder when
not in use.
If meat becomes jammed in the Cuber/Tenderizer, turn
•
off the electric grinder and unplug the grinder from the power
source.
Remove the Combs.
•
Unscrew the Housing Screws and remove the Top
•
Housing from the unit.
•
Using the Tongs, remove any meat that may be jammed in
the Blade Racks.
•
DO NOT use your fingers to remove any meat The Blades on the Driven and
Driving Racks are very sharp. Always wear cut-resistant gloves when handling
the Blade assembly.
17
13
6
5
9
2
7
14
4
3
1
8
ADDITIONAL ACCESSORIES AVAILABLE
6” Jerky Slicer Blade 07-3302
Food-Grade Silicone Spray 03-0101-W
Kevlar Gloves Small 34-0101
Kevlar Gloves Medium 34-0102
Kevlar Gloves Large 34-0103
Kevlar Gloves Extra Large 34-0104
#22 Pro-Series Electric Meat Grinder 08-2201-W
#32 Pro-Series Electric Meat Grinder 08-3201-W
Pro-2100 Vacuum Sealer 65-0101
Vacuum Sealer Bags Multi Pack 30-0107-W
These products and many more products can be ordered by visiting
w w w . w e s t o n s u p p l y . c o m or by calling
Pragotrade LLC Toll Free at 1-800- 814-489 5
Monday thru Friday 8:00am-5:00pm EST.
Outside the U.S. call 440-638-3131
3
10
11
WARNING!
Protective/cut-resistant
Kevlar Gloves are
recommended
whenever handling the
Blade assembly!
8
12
15
16
-3--10-
GENERAL SAFETY RULES
DISASSEMBLY & CLEANING INSTRUCTIONS
READ AND FULLY UNDERSTAND ALL INSTRUCTIONS
AND WARNINGS PRIOR TO USING THIS PRODUCT.
YOUR SAFETY IS MOST IMPORTANT! FAILURE TO
COMPLY WITH PROCEDURES AND SAFE GUARDS
MAY RESULT IN SERIOUS INJURY OR PROPERTY
WARNING!
1. NEVER REACH INTO the Cuber/
Tenderizer. Doing so could cause serious injury. ALWAYS USE THE PROVIDED
TONGS.
2. DO NOT push the Tongs or other utensils
into the Blades.
3. NEVER use fingers to scrape food away
from the Cuber/Tenderizer while the grinder
is in operation. SEVERE INJURY MAY
RESULT.
4. KEEP FINGERS CLEAR OF THE BLADES
AT ALL TIMES. Failure to do so may result in personal injury. The Cutting Blades/Blade
Assembly is very sharp. It is recommended
to wear Kevlar, cut resistant gloves when
handling the Blades.
5. DO NOT press or push meat into the Chute
with your fingers or any other object. Doing
so may cause personal injury and/or damage
to the unit.
6. NEVER LEAVE THE Cuber/Tenderizer
UNATTENDED. Be safe, DISCONNECT the
Grinder from power source before leaving the
work area. Close supervision is necessary
when any appliance is used near children. This
appliance is NOT to be used by children.
7. FOLLOW ALL MANUFACTURER’S
INSTRUCTIONS AND SAFETY GUIDELINES
for operating the grinder.
8. NEVER use any accessories or parts from
other manufacturers. Doing so will VOID YOUR
WARRANTY and may cause fire, electrical
shock or injury.
9. Thoroughly clean all parts that will come
into contact with food before using the
Tenderizer/Cuber. Wash all parts by hand
and dry thoroughly. WARNING! Protective/
cut-resistant Kevlar gloves are recommended
when handling the blade assembly.
10. DO NOT attempt to tenderize meat with
bones or other hard items. Damage to the
machine will occur.
DAMAGE. REMEMBER: YOUR PERSONAL
SAFETY IS YOUR RESPONSIBILITY!
11. TIE BACK loose hair and clothing, and roll
up long sleeves before operating the Cuber/Tenderizer. REMOVE ties, rings, watches,
bracelets, or other jewelry before operating the
Cuber/Tenderizer.
12. WEAR EYE PROTECTION. Wear safety
glasses. Everyday eye glasses are not safety
glasses. Safety glasses conform to ANSI Z87.1
requirements. Note: approved safety glasses
have Z87 printed or stamped on them.
13. DO NOT use outdoors.
14. DO NOT use the Cuber/Tenderizer while
under the influence of drugs, medications or
alcohol.
WARNING! Before cleaning, assembling or disassembling the Cuber/
Tenderizer Attachment make sure the PLUG of the GRINDER IS REMOVED
FROM THE OUTLET/POWER SOURCE! ALWAYS unplug the grinder when
not in use.
1. ALWAYS disconnect the grinder from the power source
before attempting to disassemble or clean the Cuber/
Tenderizer.
2. Keep children at a safe distance from unit while cleaning or
operating.
3. Remove the Cuber/Tenderizer from the grinder.
4. Remove the Combs from the Top Housing by lifting up on Combs. Figure 6
5. Remove the two Thumbscrews from the TopHousing. Set aside.
6. Remove the Top Housing. WARNING! This will expose the Cutting Blades.
Always wear cut-resistant gloves when handling the Blade assembly.
7. Using the provided
the Top Housing. Set the Screws and Lock Washers aside.
8. Carefully lift the Blade Rack Assembly from the Lower Housing.
9. Wash all parts thoroughly with warm,
soapy water. Rinse with clear water. A
long bristle brush is recommended for
cleaning the Blade Rack Assembly.
Always wear cut-resistant gloves when
handling the Blade assembly.
10. Dry thoroughly before re-assembling.
NOTE: It is highly suggested to coat all
metal parts with a food-grade silicone spray
(sold separately) to prevent corrosion.
Allen Wrench, remove the Screws to remove Chute from
Figure 6
Combs
Thumbscrew
Blade Rack
Assembly
Chute
Top Housing
Thumbscrew
SAVE THESE INSTRUCTIONS!
Refer to th em oft en an d use them t o inst ruct others .
-4--9-
Lower Housing
Electric Grinder
Adapter
DIRECTIONS FOR USE
ASSEMBLY INSTRUCTIONS
WARNING! Before cleaning, assembling or disassembling the Cuber/
Tenderizer Attachment make sure the PLUG of the GRINDER IS REMOVED
FROM THE OUTLET/POWER SOURCE! ALWAYS unplug the grinder when
not in use.
BE SURE TO FOLLOW ALL SAFETY WARNINGS
AND PRECAUTIONS THAT ARE CONTAINED IN
YOUR GRINDER INSTRUCTION MANUAL BEFORE
USING THE CUBER/TENDERIZER ATTACHMENT
WITH THE ELECTRIC GRINDER! NEVER LEAVE
MACHINE UNATTENDED!
•
Make sure the Cuber/Tenderizer is fully assembled and
correctly attached to the electric grinder.
•
Remove all bones or hard items in the meat before tenderizing or cubing. Damage
to the unit may occur if bones or hard objects are pushed through.
•
Do not cube or tenderize meat that is more than 1” (2.5 cm) thick. Thicker meat
may get lodged in Blades, which may cause damage to the product.
Use Tongs to insert the meat to be tenderized or cubed into the mouth of the
•
Chute until the meat comes in contact with the Blades. The meat will be pulled
through the unit by the Blade movement.
If a piece of meat is too short to reach the Blades, use the provided Tongs to
•
guide the meat to the Blades.
CAUTION! DO NOT press or push the meat into the Chute with your fingers or
•
any other object. Doing so may cause personal injury and/or damage to the unit. DO
NOT push the Tongs or other utensils into the Blades.
It may be necessary to pass the meat through the Cuber/Tenderizer several
•
times to obtain the desired results. You may also pass the meat through at different
angles if a different result is desired.
When finished tenderizing or cubing the meat, turn off the electric grinder and
•
unplug it from the power source.
Clean the unit before and after each use.
•
WARNING! Before cleaning, assembling or disassembling the Cuber/
Tenderizer Attachment make sure the PLUG of the GRINDER IS REMOVED
FROM THE OUTLET/POWER SOURCE! ALWAYS unplug the grinder when
not in use.
BE SURE TO FOLLOW ALL SAFETY WARNINGS
AND PRECAUTIONS THAT ARE CONTAINED
IN YOUR GRINDER INSTRUCTION MANUAL
BEFORE USING THE CUBER/TENDERIZER
ATTACHMENT WITH THE ELECTRIC
GRINDER! NEVER LEAVE THE MACHINE
UNATTENDED!
PRIOR TO FIRST USE: Disassemble the Cuber/
Tenderizer and hand wash each part in warm, soapy
water. Rinse with clear water. Dry thoroughly before
re-assembling. WARNING! This will expose the
Cutting Blades. ALWAYS wear cut-resistant gloves
when handling the Blade assembly.
1. If the Shaft Adapter is not already attached to the
Cuber/Tenderizer attachment, loosen the Set Screw
on the Shaft Adapter using the supplied Allen Wrench.
Slide the Shaft Adapter onto the Driving Blade Rack Shaft and tighten the Set Screw. DO NOT over tighten.
Figure 1
2. To install the Chute onto the Top
Housing, remove the Top Housing from
the Lower Housing. Secure the Chute to
the Top Housing using the two Screws and Lock Washers. DO NOT over tighten.
3. Insert the Driving Blade Rack into the
Lower Housing, guiding the Drive Shaft
into the bearing journals. NOTE: When
installing the Blade Rack Assembly, you
must position the drive shaft with the Shaft
Chute
Adapter through the hole in the Electric
Grinder Adapter before seating into the
Top Housing
bearing journals. Figure 2
4. Install the Driven Blade Rack
Thumbscrew
into the Lower Housing making
sure the teeth on the Driving Blade Rack are properly meshed together
with the teeth on the Driven Blade Rack.
5. Position the Top Housing onto
Blade
Assembly
Driving Blade
the Lower Housing and line up the
screw holes.
6. Secure the Top Housing to the
Lower Housing
Lower Housing using the Housing
Thumbscrews. DO NOT over
tighten.
Electric Grinder
-5--8-
Adapter
Electric Grinder Adapter
Shaft Adapter
Shaft
Adapter
Set Screw
Combs
Adapter Mountig
Thumbscrew
Driven Blade
Figure 1
Bolts
Figure 2
7. Insert the Left Comb and Right Comb into
the Top Housing. Figure 3 NOTE: The Left Comb is marked with an “L” on the upper portion
of the Comb. The Top Housing is marked with
an “L Comb” and “R Comb” to aid in Comb
installation.
Figure 3
ATTACHING TO THE GRINDER
WARNING! Before cleaning, assembling or disassembling the Cuber/
Tenderizer Attachment make sure the PLUG of the GRINDER IS REMOVED
FROM THE OUTLET/POWER SOURCE! ALWAYS unplug the grinder when
not in use.
BE SURE TO FOLLOW ALL SAFETY WARNINGS AND PRECAUTIONS
THAT ARE CONTAINED IN YOUR GRINDER INSTRUCTION MANUAL
BEFORE USING THE CUBER/TENDERIZER ATTACHMENT WITH THE
ELECTRIC GRINDER! NEVER LEAVE MACHINE UNATTENDED!
1. ALWAYS disconnect the grinder from the power source before attaching the
Cuber/Tenderizer.
2. Unscrew the head locking knob (turn counter-clockwise) on the electric grinder
until the end of the threads are no longer protruding into the grinder output housing.
3. Line up the grinder pin with the
Grinder Adapter notch on the Cuber/Tenderizer.
Line up the Shaft Adapter splines with the grinder output housing. Figure 4
NOTE: You may have to reposition the Cuber/Tenderizer Shaft splines so that
they match up with the grinder output shaft. Make sure the grinder head locking knob
lines up with the groove on the electric grinder adapter.
4. Once the Cuber/Tenderizer Attachment is properly positioned on to the electric
grinder, tighten the grinder head locking knob.
Figure 4
Cuber/Tenderizer
Grinder Pin
Output Shaft
Splines
Grinder
Head Locking
Knob of Grinder
Shaft Adapter
Notch
Attachment
Groove
Shaft Adapter
Splines
-7--6-
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.